Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Modded Cars
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Jaguar

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Overview

This white 2012 Jaguar XFR has been modified in three stages: a Mina supercharger pulley and Mina exhaust, then a RICA ECU tune. Owner-reported Dynocom dynamometer runs in Calgary show the car rising from about 453–458 wheel horsepower at baseline to up to 567.9 hp after the final calibration. All figures are owner-reported.

Pulley, exhaust and calibration

Three baseline pulls ranged from 453.4 to 457.5 wheel horsepower. After the Mina pulley and exhaust were fitted, a second dyno session was run; the owner noted tyre slip on a subsequent pull and a stronger low-speed throttle response. A RICA ECU tune followed.

Final dyno results

The final graph shows three runs of 529.4, 559.7 and 567.9 hp. The highest run lists 492.2 lb-ft, while another run peaked at 494.4 lb-ft. Separate graphs compare the baseline, the pulley and exhaust, and the final calibration.

Car photograph and dyno graph posted by H.Jones on Jaguar Forums, reproduced with permission. Car photograph · Dyno graph

Sources

Jaguar Forums tuning thread: baseline dyno runsJaguar Forums tuning thread: pulley and exhaust dyno updateJaguar Forums thread: final modifications listJaguar Forums tuning thread: final dyno graphs and comments

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: H.Jones’s 2012 Jaguar XFR pulley and tune build

Overview

This white 2012 Jaguar XFR has been modified in three stages: a Mina supercharger pulley and Mina exhaust, then a RICA ECU tune. Owner-reported Dynocom dynamometer runs in Calgary show the car rising from about 453–458 wheel horsepower at baseline to up to 567.9 hp after the final calibration. All figures are owner-reported.

H.Jones’s white 2012 Jaguar XFR after its modifications

Pulley, exhaust and calibration

Three baseline pulls ranged from 453.4 to 457.5 wheel horsepower. After the Mina pulley and exhaust were fitted, a second dyno session was run; the owner noted tyre slip on a subsequent pull and a stronger low-speed throttle response. A RICA ECU tune followed.

Final dyno results

The final graph shows three runs of 529.4, 559.7 and 567.9 hp. The highest run lists 492.2 lb-ft, while another run peaked at 494.4 lb-ft. Separate graphs compare the baseline, the pulley and exhaust, and the final calibration.

Dynocom graph showing three final XFR dyno runs and their peak figures

Car photograph and dyno graph posted by H.Jones on Jaguar Forums, reproduced with permission. Car photograph · Dyno graph

Sources

Revision 3: H.Jones’s 2012 Jaguar XFR pulley and tune build

Overview

This white 2012 Jaguar XFR has been modified in three stages: a Mina supercharger pulley and Mina exhaust, then a RICA ECU tune. Owner-reported Dynocom dynamometer runs in Calgary show the car rising from about 453–458 wheel horsepower at baseline to up to 567.9 hp after the final calibration. All figures are owner-reported.

H.Jones’s white 2012 Jaguar XFR after its modifications

Pulley, exhaust and calibration

Three baseline pulls ranged from 453.4 to 457.5 wheel horsepower. After the Mina pulley and exhaust were fitted, a second dyno session was run; the owner noted tyre slip on a subsequent pull and a stronger low-speed throttle response. A RICA ECU tune followed.

Final dyno results

The final graph shows three runs of 529.4, 559.7 and 567.9 hp. The highest run lists 492.2 lb-ft, while another run peaked at 494.4 lb-ft. Separate graphs compare the baseline, the pulley and exhaust, and the final calibration.

Dynocom graph showing three final XFR dyno runs and their peak figures

Car photograph and dyno graph posted by H.Jones on Jaguar Forums, reproduced with permission. Car photograph · Dyno graph

Sources