Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Reference
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Maserati

This page records factory changes by year, differences between markets, and diagnostic guidance for carburettor 425-type cars. Sources are a translated Italian magazine dossier and owner question-and-answer pages on an enthusiast reference site. Figures are as published there; where they contradict other pages on this wiki the difference is stated.

Factory changes by year

YearChange
1981Biturbo previewed (14 December). 1,996 cc V6 with one belt-driven cam per bank, three valves per cylinder (a small and a larger inlet valve for swirl, and one exhaust valve operated through a single cup, a De Tomaso patent), one twin-choke Weber under a sealed plenum, two IHI turbos, five-speed ZF. 180 bhp at 6,000 rpm, 1,086 kg.
1982First cars delivered in April; public presentation at Geneva in March.
1983Export 2,491 cc engine, made by raising the bore to 91.6 mm; the dossier says it had cast-iron liners and different valve diameters and gear ratios. Swiss and Swedish cars had a cold-start aid and a system to remove fuel vapour from the plenum; US cars had exhaust air injection and two-way catalysts. MABC from engine number 3001.
1984Biturbo S (two air-to-air intercoolers beside the carburettor, bonnet NACA ducts, re-mapped boost controller, 205 bhp); four-door 425 with 2.5 litre engine and Sensitork differential (built under licence by Gleason) replacing the Salisbury unit.
1985Biturbo II: Nikasil-type aluminium liners (a Moto Guzzi-patented process), water cooling replacing oil cooling for the turbos, Sensitork differential. Biturbo S II rated 210 bhp. A US-market official recall addressed catalytic converter heat insulation after vehicle fires. 3-speed ZF automatic optional.
1985 (US)A limited run of about 500 US-market Biturbo E cars was modified by the West Coast distributor with Spearco air-to-water intercoolers to reach 205 bhp despite emissions equipment.
1986US cars needed a Weber 34 carburettor instead of the 36 to meet emissions rules. Injected Biturbo i and 420i introduced with an IAW (Weber-Marelli) system; larger inlet and exhaust valves from the 2.5 litre heads gave a small power rise and fixed the cold-start problem of the carburettor cars.
1987Biturbo Si and 420 Si with injection, equal-diameter inlet valves, 223 bhp, intercoolers moved behind the grille (bonnet ducts became cosmetic).
1988–89222/422 replace the Si cars; 2.24v (1989) with four cams and four valves per cylinder, 245 bhp.
1991Racing: 283 bhp 24-valve V6 with a Getrag gearbox. 222 SR, 430 4v and 222 4v followed; Ghibli (306 bhp 2.0) launched.

The dossier credits the water-cooled turbo system to the 228 first, then adopted across the range. Other sources date it to the 1985 Biturbo II or the 1983 S; treat the exact start per model as unconfirmed.

What this resolves and what it does not

  • The "36 or 34" carburettor question: the 36 is the normal fitment and the 34 is reported on US-emissions cars. A later 34 DAT on 1986 2.5 litre cars is also reported elsewhere, so check the carburettor plate.
  • MABC began from engine number 3001, which is a more precise marker than "June 1983" or "1984".
  • The 2.5 litre export engine's liner material is given here as cast iron, whereas other sources describe wet Nikasil-type liners throughout; the 1985 Biturbo II is the documented switch to Nikasil.
  • Still not given: jet sizes, float level, firing order, injected-car ignition timing.

Carburettor 425 figures and diagnosis

  • Ignition timing: European-specification cars are quoted at 13° BTDC; US versions differ, so check the manual for the market.
  • Hot idle speed: about 1,000 rpm. A carburettor car stuck near 2,000 rpm is abnormal.
  • High idle checklist: check the throttle cable and carpet first; confirm the choke is fully off (the warning light is unreliable, and the car starts without choke after a couple of throttle prods); disconnect the throttle cable at the carburettor to separate cable faults from carburettor faults; lift the plenum to test the carburettor itself. Undo the plenum cap-head bolts carefully, starting with the right-hand corner bolt, which can snap the corner off the casting. Persisting high idle then points to an internal carburettor fault needing overhaul, or wrong ignition timing.
  • Engine swaps: a 2.24v engine and gearbox bolt into a 425i, but the injection loom and both ECUs must come with it or it will not run.
  • Cold or hot start spitting on a reassembled carburettor car: the vacuum hoses are unlikely to cause a non-start; check the fuel lines are connected the right way round.
  • Rough idle with the plenum off points to a partly blocked idle jet.

Other faults reported on 425-type cars

  • Loose power steering pump: an unsecured pump pulley or bracket threw off the cam belt on one car, causing internal engine damage. Re-tighten pump bolts after any work.
  • Gearbox layshaft bearings: a knock at idle that vanishes with the clutch pressed, or at about 1,000 rpm, is the layshaft bearings. It worsens with mileage and need not be fixed immediately; renewing them needs the gearbox out (about £1,000 at a specialist at the time). A zinging noise through the gear lever is normal on five-speed dog-leg ZF boxes and is worse on injected cars.
  • Power steering leaks: usually the reservoir-to-pump hose (a superseded Ghibli hose is better) or the rack pinion seal; pump leaks are rare.
  • Green fluid in the passenger footwell: a heater hose through the bulkhead or the heater matrix (dashboard removal needed); also check for a blocked air-conditioning drain.
  • Oil leaks from the engine, gearbox, steering and axle are common; the rear axle was the weak point of early cars.
  • Hot idle test: let the engine idle for ten minutes; the cooling fans should cut in and out, and puffs of blue smoke after a long idle suggest failed turbo bearings.
  • Belt interval: this source advises every 24,000 miles or four years; another page says 25,000 miles or two years. The mileage agrees; the age differs, so use the shorter.
  • Boost check: the gauge should reach the start of the orange band; below that suggests a boost controller fault, and into the red suggests modification or a seized wastegate. Oil in the air filter indicates a breathing engine from excess boost.
  • Wheels: original carburettor and Italian injection cars use four-stud wheels (Lancia Delta pattern is reported to match); 7 × 16 is the largest seen, and rubs the front track rod ends on lock.
  • Body: corrosion shows on lower doors, front wing and bonnet leading edges, bootlid edge and outer sills; check the rear door apertures, windscreen corners and front chassis legs for accident damage.

References

Back to the Maserati Biturbo hub.