Tuning Wiki
Browse Maserati

This article covers Biturbo factory changes by year, differences between markets, and diagnostic guidance for carburettor 425-type cars. Figures come from a translated Italian magazine dossier and owner question-and-answer pages on an enthusiast reference site, and where they contradict other pages on this wiki the difference is stated.

Factory changes by year

YearChange
1981Biturbo previewed (14 December). 1,996 cc V6 with one belt-driven cam per bank, three valves per cylinder (a small and a larger inlet valve for swirl, and one exhaust valve operated through a single cup, a De Tomaso patent), one twin-choke Weber under a sealed plenum, two IHI turbos, five-speed ZF. 180 bhp at 6,000 rpm, 1,086 kg.
1982First cars delivered in April; public presentation at Geneva in March.
1983Export 2,491 cc engine, made by raising the bore to 91.6 mm; the dossier says it had cast-iron liners and different valve diameters and gear ratios. Swiss and Swedish cars had a cold-start aid and a system to remove fuel vapour from the plenum; US cars had exhaust air injection and two-way catalysts. MABC from engine number 3001.
1984Biturbo S (two air-to-air intercoolers beside the carburettor, bonnet NACA ducts, re-mapped boost controller, 205 bhp); four-door 425 with 2.5 litre engine and Sensitork differential (built under licence by Gleason) replacing the Salisbury unit.
1985Biturbo II: Nikasil-type aluminium liners (a Moto Guzzi-patented process), water cooling replacing oil cooling for the turbos, Sensitork differential. Biturbo S II rated 210 bhp. A US-market official recall addressed catalytic converter heat insulation after vehicle fires. 3-speed ZF automatic optional.
1985 (US)A limited run of about 500 US-market Biturbo E cars was modified by the West Coast distributor with Spearco air-to-water intercoolers to reach 205 bhp despite emissions equipment.
1986US cars needed a Weber 34 carburettor instead of the 36 to meet emissions rules. Injected Biturbo i and 420i introduced with an IAW (Weber-Marelli) system; larger inlet and exhaust valves from the 2.5 litre heads gave a small power rise and fixed the cold-start problem of the carburettor cars.
1987Biturbo Si and 420 Si with injection, equal-diameter inlet valves, 223 bhp, intercoolers moved behind the grille (bonnet ducts became cosmetic).
1988–89222/422 replace the Si cars; 2.24v (1989) with four cams and four valves per cylinder, 245 bhp.
1991Racing: 283 bhp 24-valve V6 with a Getrag gearbox. 222 SR, 430 4v and 222 4v followed; Ghibli (306 bhp 2.0) launched.

The dossier credits the water-cooled turbo system to the 228 first, then adopted across the range. Other sources date it to the 1985 Biturbo II or the 1983 S, so the exact start per model is unconfirmed.

Resolved points

  • The "36 or 34" carburettor question: the 36 is the normal fitment and the 34 is reported on US-emissions cars. A later 34 DAT on 1986 2.5 litre cars is also reported elsewhere, so the carburettor plate should be checked.
  • MABC began from engine number 3001, which is a more precise marker than "June 1983" or "1984".
  • The 2.5 litre export engine's liner material is given in the dossier as cast iron, whereas other sources describe wet Nikasil-type liners throughout; the 1985 Biturbo II is the documented switch to Nikasil.

Carburettor 425 figures and diagnosis

  • Ignition timing: European-specification cars are quoted at 13° BTDC; US versions differ, so the manual for the market should be checked.
  • Hot idle speed: about 1,000 rpm. A carburettor car stuck near 2,000 rpm is abnormal.
  • High idle checklist: check the throttle cable and carpet first; confirm the choke is fully off (the warning light is unreliable, and the car starts without choke after a couple of throttle prods); disconnect the throttle cable at the carburettor to separate cable faults from carburettor faults; lift the plenum to test the carburettor itself. The plenum cap-head bolts should be undone carefully, starting with the right-hand corner bolt, which can snap the corner off the casting. Persisting high idle then points to an internal carburettor fault needing overhaul, or wrong ignition timing.
  • Engine swaps: a 2.24v engine and gearbox bolt into a 425i, but the injection loom and both ECUs must come with it or it will not run.
  • Cold or hot start spitting on a reassembled carburettor car: the vacuum hoses are unlikely to cause a non-start; the fuel lines should be checked for correct connection.
  • Rough idle with the plenum off points to a partly blocked idle jet.

Other faults reported on 425-type cars

  • Loose power steering pump: an unsecured pump pulley or bracket threw off the cam belt on one car, causing internal engine damage. Pump bolts should be re-tightened after any work.
  • Gearbox layshaft bearings: a knock at idle that vanishes with the clutch pressed, or at about 1,000 rpm, is the layshaft bearings. It worsens with mileage and need not be fixed immediately; renewing them needs the gearbox out (about £1,000 at a specialist at the time). A zinging noise through the gear lever is normal on five-speed dog-leg ZF boxes and is worse on injected cars.
  • Power steering leaks: usually the reservoir-to-pump hose (a superseded Ghibli hose is better) or the rack pinion seal; pump leaks are rare.
  • Green fluid in the passenger footwell: a heater hose through the bulkhead or the heater matrix (dashboard removal needed); also check for a blocked air-conditioning drain.
  • Oil leaks from the engine, gearbox, steering and axle are common; the rear axle was the weak point of early cars.
  • Hot idle test: let the engine idle for ten minutes; the cooling fans should cut in and out, and puffs of blue smoke after a long idle suggest failed turbo bearings.
  • Belt interval: every 24,000 miles or four years is advised here; another page says 25,000 miles or two years. The mileage agrees; the age differs, so the shorter should be used.
  • Boost check: the gauge should reach the start of the orange band; below that suggests a boost controller fault, and into the red suggests modification or a seized wastegate. Oil in the air filter indicates a breathing engine from excess boost.
  • Wheels: original carburettor and Italian injection cars use four-stud wheels (Lancia Delta pattern is reported to match); 7 × 16 is the largest seen, and rubs the front track rod ends on lock.
  • Body: corrosion shows on lower doors, front wing and bonnet leading edges, bootlid edge and outer sills; the rear door apertures, windscreen corners and front chassis legs should be checked for accident damage.

Not established

Jet sizes, float level, firing order and injected-car ignition timing are not given in the sources.

References

Back to the Maserati Biturbo hub.