Page organisation in this revision
- Page type
- Technical article
- Subject
- Modded Cars
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Ferrari
Changes from revision 2 to revision 2
Removed text is struck through; added text is highlighted.
This black Ferrari 348 was bought standard and developed over several years with F355 wheels, 360 seats and a 360 Challenge steering wheel. A later project acquired a 348-based race engine associated with a Le Mans programme, with an owner-reported engine-dyno output of 480 bhp, intended for road use with a MoTeC M800 ECU.
Photographs shared by Angelis in the PistonHeads build thread, reproduced with permission.
Chassis, interior and servicing
18-inch F355 magnesium wheels with 15 mm front and 25 mm rear spacers.360 carbon-fibre seats and a 360 Challenge steering wheel.Engine-out service, upgraded ignition leads and silicone hoses.Complete respray from metallic black to solid black.
Le Mans engine project
A 348-based race engine associated with a Le Mans programme was acquired, with an engine-dyno output of 480 bhp reported by the owner (unverified). The plan is to adapt it for road use with a MoTeC M800. The build thread records setbacks, so the purchase and intended installation should be read as a stage of the project rather than a completed conversion.
Sources
PistonHeads build thread: original build and updatesPistonHeads build thread: engine arrival and ECU update
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Angelis’s modified Ferrari 348 and Le Mans engine project
This black Ferrari 348 was bought standard and developed over several years with F355 wheels, 360 seats and a 360 Challenge steering wheel. A later project acquired a 348-based race engine associated with a Le Mans programme, with an owner-reported engine-dyno output of 480 bhp, intended for road use with a MoTeC M800 ECU.


Photographs shared by Angelis in the PistonHeads build thread, reproduced with permission.
Chassis, interior and servicing
- 18-inch F355 magnesium wheels with 15 mm front and 25 mm rear spacers.
- 360 carbon-fibre seats and a 360 Challenge steering wheel.
- Engine-out service, upgraded ignition leads and silicone hoses.
- Complete respray from metallic black to solid black.
Le Mans engine project
A 348-based race engine associated with a Le Mans programme was acquired, with an engine-dyno output of 480 bhp reported by the owner (unverified). The plan is to adapt it for road use with a MoTeC M800. The build thread records setbacks, so the purchase and intended installation should be read as a stage of the project rather than a completed conversion.
Sources
Revision 2: Angelis’s modified Ferrari 348 and Le Mans engine project
This black Ferrari 348 was bought standard and developed over several years with F355 wheels, 360 seats and a 360 Challenge steering wheel. A later project acquired a 348-based race engine associated with a Le Mans programme, with an owner-reported engine-dyno output of 480 bhp, intended for road use with a MoTeC M800 ECU.


Photographs shared by Angelis in the PistonHeads build thread, reproduced with permission.
Chassis, interior and servicing
- 18-inch F355 magnesium wheels with 15 mm front and 25 mm rear spacers.
- 360 carbon-fibre seats and a 360 Challenge steering wheel.
- Engine-out service, upgraded ignition leads and silicone hoses.
- Complete respray from metallic black to solid black.
Le Mans engine project
A 348-based race engine associated with a Le Mans programme was acquired, with an engine-dyno output of 480 bhp reported by the owner (unverified). The plan is to adapt it for road use with a MoTeC M800. The build thread records setbacks, so the purchase and intended installation should be read as a stage of the project rather than a completed conversion.
Sources