Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Performance
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Engine oil separates the moving surfaces, carries heat and helps seal the rings. Higher output means higher bearing loads and more heat to move, so the oil system is one of the limits on how much of a gain the engine can keep. The coolant loop is on engine cooling for higher output.

What the oil does

Engine oil reduces friction and wear with a separating film, cleans through dispersants and detergents, neutralises acids, improves piston-ring sealing, carries heat away from moving parts and coats metal to keep oxygen off it (Wikipedia: Motor oil).

Viscosity and temperature

A multigrade such as 5W-30 has a winter grade, which specifies viscosity at cold temperatures, and a second grade, which specifies viscosity at operating temperature. Multigrade oils need polymeric viscosity index improvers. A higher viscosity index means viscosity changes less with temperature. Synthetics generally have a higher index and need fewer improvers, which are the part of the oil most vulnerable to thermal and mechanical degradation. Heat and mechanical shear reduce viscosity and the oil's reserve alkalinity. Lower viscosity weakens lubrication and raises wear and overheating risk. If reserve alkalinity reaches zero, acids form and corrode the engine. Oil near the top piston ring is exposed to about 160 °C in petrol engines and over 315 °C in diesels.

Thinner oil flows more easily but builds pressure less readily. Low pressure can cause loss of hydrodynamic lubrication and metal-to-metal contact, while excessive pressure wastes energy and can damage seals (EngineLabs: wet sump oiling systems). Use the viscosity the engine maker specifies, and discuss any change with the maker or an engine builder.

Oil temperature and coolers

Oil leaves heat through airflow over the sump, an oil cooler and, in some engines, piston-cooling oil sprays. Its thermal capacity means it takes longer to reach design temperature than the coolant does. Because viscosity breakdown is tied to temperature, a cooler can reduce those problems, and cooler lines must match in size throughout the system to hold pressure and flow.

Wet-sump capacity, baffles and the pickup

These design points apply to harder use (EngineLabs, with Canton Racing Products):

Capacity. More oil reduces the chance of starvation and helps stabilise oil temperature. Overfilling causes windage. A deeper sump is limited by ground clearance, and a T-sump can add capacity without much depth. Windage trays. A tray directs oil away from the crankshaft and back to the sump, reducing drag. The benefit is most apparent around 5,000 rpm and, for engines spending much time above that, can free up to 15 hp. Screens perform slightly better on a dyno; louvred trays are stronger and are suited to aggressive road racing. Baffles. The right layout depends on use: stationary walls and trap doors for drag racing, four trap doors for road courses, and one-sided baffling for circle track. Pickup. A tube too small can cause cavitation that damages the pump, and a tube too large is also wrong for the engine. With a baffled pan a gap of about 3/8 inch between the pan and pickup is a common target. Match the pickup to the pump. Accumulators. An accumulator supplies reserve oil when pressure drops and refills when it recovers. In one sample race engine, logged data showed far fewer low-pressure events at high rpm with one fitted.

A problem that appears after a few laps usually points to slow oil return, and adding capacity can help. These details come from V8 and race engines, so treat the dimensions as examples rather than specifications for other engines.

Forced induction

A turbocharger needs its own oil supply, and the turbocharger maker specifies the feed and drain arrangement. Follow it, because the oil feed and drain are part of any turbo installation: see turbocharger upgrades and modifications and balancing and rebuilding a turbocharger.

Checking the oil system

Log oil pressure and, where fitted, oil temperature under sustained load, not only at idle, and compare against a baseline. Look at oil level and condition, check for a restricted pickup, a failing pump or relief valve, and recheck after a track day or dyno session. Pistons, rods and bearings rely on the oil film to survive the loads described on pistons, connecting rods and rod bolts. A new or rebuilt engine has its own oil routine: engine break-in after a rebuild.

Sources

Motor oil. Wikipedia. Functions, SAE grades, viscosity index, thermal breakdown and oil cooling. Accessed 2026-11-19. Everything You Ever Wanted To Know About Wet Sump Oiling Systems. Jefferson Bryant, EngineLabs, 12 August 2025, with Canton Racing Products. Capacity, windage trays, baffles, pickups, pressure, coolers and accumulators. Accessed 2026-11-19.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Engine oil, oil coolers and lubrication under load

Engine oil separates the moving surfaces, carries heat and helps seal the rings. Higher output means higher bearing loads and more heat to move, so the oil system is one of the limits on how much of a gain the engine can keep. The coolant loop is on engine cooling for higher output.

What the oil does

Engine oil reduces friction and wear with a separating film, cleans through dispersants and detergents, neutralises acids, improves piston-ring sealing, carries heat away from moving parts and coats metal to keep oxygen off it (Wikipedia: Motor oil).

Viscosity and temperature

  • A multigrade such as 5W-30 has a winter grade, which specifies viscosity at cold temperatures, and a second grade, which specifies viscosity at operating temperature.
  • Multigrade oils need polymeric viscosity index improvers. A higher viscosity index means viscosity changes less with temperature. Synthetics generally have a higher index and need fewer improvers, which are the part of the oil most vulnerable to thermal and mechanical degradation.
  • Heat and mechanical shear reduce viscosity and the oil's reserve alkalinity. Lower viscosity weakens lubrication and raises wear and overheating risk. If reserve alkalinity reaches zero, acids form and corrode the engine.
  • Oil near the top piston ring is exposed to about 160 °C in petrol engines and over 315 °C in diesels.

Thinner oil flows more easily but builds pressure less readily. Low pressure can cause loss of hydrodynamic lubrication and metal-to-metal contact, while excessive pressure wastes energy and can damage seals (EngineLabs: wet sump oiling systems). Use the viscosity the engine maker specifies, and discuss any change with the maker or an engine builder.

Oil temperature and coolers

Oil leaves heat through airflow over the sump, an oil cooler and, in some engines, piston-cooling oil sprays. Its thermal capacity means it takes longer to reach design temperature than the coolant does. Because viscosity breakdown is tied to temperature, a cooler can reduce those problems, and cooler lines must match in size throughout the system to hold pressure and flow.

Wet-sump capacity, baffles and the pickup

These design points apply to harder use (EngineLabs, with Canton Racing Products):

  • Capacity. More oil reduces the chance of starvation and helps stabilise oil temperature. Overfilling causes windage. A deeper sump is limited by ground clearance, and a T-sump can add capacity without much depth.
  • Windage trays. A tray directs oil away from the crankshaft and back to the sump, reducing drag. The benefit is most apparent around 5,000 rpm and, for engines spending much time above that, can free up to 15 hp. Screens perform slightly better on a dyno; louvred trays are stronger and are suited to aggressive road racing.
  • Baffles. The right layout depends on use: stationary walls and trap doors for drag racing, four trap doors for road courses, and one-sided baffling for circle track.
  • Pickup. A tube too small can cause cavitation that damages the pump, and a tube too large is also wrong for the engine. With a baffled pan a gap of about 3/8 inch between the pan and pickup is a common target. Match the pickup to the pump.
  • Accumulators. An accumulator supplies reserve oil when pressure drops and refills when it recovers. In one sample race engine, logged data showed far fewer low-pressure events at high rpm with one fitted.

A problem that appears after a few laps usually points to slow oil return, and adding capacity can help. These details come from V8 and race engines, so treat the dimensions as examples rather than specifications for other engines.

Forced induction

A turbocharger needs its own oil supply, and the turbocharger maker specifies the feed and drain arrangement. Follow it, because the oil feed and drain are part of any turbo installation: see turbocharger upgrades and modifications and balancing and rebuilding a turbocharger.

Checking the oil system

Log oil pressure and, where fitted, oil temperature under sustained load, not only at idle, and compare against a baseline. Look at oil level and condition, check for a restricted pickup, a failing pump or relief valve, and recheck after a track day or dyno session. Pistons, rods and bearings rely on the oil film to survive the loads described on pistons, connecting rods and rod bolts. A new or rebuilt engine has its own oil routine: engine break-in after a rebuild.

Sources

Revision 3: Engine oil, oil coolers and lubrication under load

Engine oil separates the moving surfaces, carries heat and helps seal the rings. Higher output means higher bearing loads and more heat to move, so the oil system is one of the limits on how much of a gain the engine can keep. The coolant loop is on engine cooling for higher output.

What the oil does

Engine oil reduces friction and wear with a separating film, cleans through dispersants and detergents, neutralises acids, improves piston-ring sealing, carries heat away from moving parts and coats metal to keep oxygen off it (Wikipedia: Motor oil).

Viscosity and temperature

  • A multigrade such as 5W-30 has a winter grade, which specifies viscosity at cold temperatures, and a second grade, which specifies viscosity at operating temperature.
  • Multigrade oils need polymeric viscosity index improvers. A higher viscosity index means viscosity changes less with temperature. Synthetics generally have a higher index and need fewer improvers, which are the part of the oil most vulnerable to thermal and mechanical degradation.
  • Heat and mechanical shear reduce viscosity and the oil's reserve alkalinity. Lower viscosity weakens lubrication and raises wear and overheating risk. If reserve alkalinity reaches zero, acids form and corrode the engine.
  • Oil near the top piston ring is exposed to about 160 °C in petrol engines and over 315 °C in diesels.

Thinner oil flows more easily but builds pressure less readily. Low pressure can cause loss of hydrodynamic lubrication and metal-to-metal contact, while excessive pressure wastes energy and can damage seals (EngineLabs: wet sump oiling systems). Use the viscosity the engine maker specifies, and discuss any change with the maker or an engine builder.

Oil temperature and coolers

Oil leaves heat through airflow over the sump, an oil cooler and, in some engines, piston-cooling oil sprays. Its thermal capacity means it takes longer to reach design temperature than the coolant does. Because viscosity breakdown is tied to temperature, a cooler can reduce those problems, and cooler lines must match in size throughout the system to hold pressure and flow.

Wet-sump capacity, baffles and the pickup

These design points apply to harder use (EngineLabs, with Canton Racing Products):

  • Capacity. More oil reduces the chance of starvation and helps stabilise oil temperature. Overfilling causes windage. A deeper sump is limited by ground clearance, and a T-sump can add capacity without much depth.
  • Windage trays. A tray directs oil away from the crankshaft and back to the sump, reducing drag. The benefit is most apparent around 5,000 rpm and, for engines spending much time above that, can free up to 15 hp. Screens perform slightly better on a dyno; louvred trays are stronger and are suited to aggressive road racing.
  • Baffles. The right layout depends on use: stationary walls and trap doors for drag racing, four trap doors for road courses, and one-sided baffling for circle track.
  • Pickup. A tube too small can cause cavitation that damages the pump, and a tube too large is also wrong for the engine. With a baffled pan a gap of about 3/8 inch between the pan and pickup is a common target. Match the pickup to the pump.
  • Accumulators. An accumulator supplies reserve oil when pressure drops and refills when it recovers. In one sample race engine, logged data showed far fewer low-pressure events at high rpm with one fitted.

A problem that appears after a few laps usually points to slow oil return, and adding capacity can help. These details come from V8 and race engines, so treat the dimensions as examples rather than specifications for other engines.

Forced induction

A turbocharger needs its own oil supply, and the turbocharger maker specifies the feed and drain arrangement. Follow it, because the oil feed and drain are part of any turbo installation: see turbocharger upgrades and modifications and balancing and rebuilding a turbocharger.

Checking the oil system

Log oil pressure and, where fitted, oil temperature under sustained load, not only at idle, and compare against a baseline. Look at oil level and condition, check for a restricted pickup, a failing pump or relief valve, and recheck after a track day or dyno session. Pistons, rods and bearings rely on the oil film to survive the loads described on pistons, connecting rods and rod bolts. A new or rebuilt engine has its own oil routine: engine break-in after a rebuild.

Sources