A car that accelerates harder has to stop harder, and repeated heavy braking heats the whole brake system, fluid included. This page covers the fluid side, which is the part of the system that is easiest to overlook and cheapest to fix. Pads, discs and calipers should be chosen with the brake or vehicle maker; this wiki does not yet cover them. See also power, weight and traction for why traction limits braking as well as acceleration.
How fluid causes fade
Brake fluid transmits pedal force as hydraulic pressure, and a liquid cannot be compressed. If the fluid in a caliper boils, the vapour can be compressed, so the pedal travels further and the caliper receives less pressure, and in the worst case the pedal goes to the floor. This is vapour in the fluid, which is a different cause from fade in the pad material.
Moisture is the problem. Brake fluid is hygroscopic, so it absorbs water over time, and no brake system is perfectly sealed, so every system takes some in ([NASA Speed News: Brake Fluid Basics](https://nasaspeed.news/tech/brakes/brake-fluid-basics-understanding-the-fine-points-can-help-you-select-the-best-fluid-for-your-needs/)). Water lowers the boiling point of the fluid, and a caliper in a hot brake can bring the fluid in it above that lowered temperature.
Dry and wet boiling point
Fluid is described by two boiling points. The dry figure is for fresh fluid from a sealed container. The wet figure is for fluid that has absorbed moisture, and is closer to what is in a car that has been on the road for a year or two. A fluid's wet boiling point is the more useful number for judging a margin against boiling in service.
Typical minimum figures for the common grades, in degrees Fahrenheit, from the same source:
| Grade | Dry boiling point | Wet boiling point | Base |
|---|---|---|---|
| DOT 3 | 401 | 284 | Glycol ether |
| DOT 4 | 446 | 311 | Borate ester |
| DOT 5 | 500 | 356 | Silicone |
| DOT 5.1 | 500 | 356 | Borate ester |
Those are grade minimums. Individual fluids can exceed them, and the figures that matter are the ones on the product's own data sheet. Use the grade the vehicle maker specifies for the system.
Mixing and compatibility
- DOT 3, DOT 4 and DOT 5.1 can be mixed with each other. DOT 5 mixes only with DOT 5, and a silicone DOT 5 fluid should not be put into a system built for a glycol or borate fluid.
- Silicone fluid is not suited to hard use. It does not absorb moisture, so any water that gets in can collect and boil, and it can hold dissolved air.
- Glycol-based fluids damage paint, so wipe up spills.
How often to change it
The rule of thumb for DOT 4 is a 24-month life. For performance driving, a full flush and refill each year is recommended, and some competition teams flush after each session, while amateurs more often bleed between events or when the pedal feels soft (NASA Speed News). A spongy pedal after hard use is a warning to stop and investigate, not a setting to adjust.
Checking the system
- Note the age of the fluid and the grade in the reservoir before any power upgrade.
- Flush the whole system, not only the reservoir, and bleed in the order the vehicle maker specifies.
- Check the pedal feel after a test of repeated hard braking, in a safe place, and again once the brakes have cooled.
- Look at hoses, calipers and fittings for leaks or swelling.
The brake system is a safety system. Brake work should be done to the maker's procedure by a competent person, and the diagnostic page on ABS failures and warning lights covers faults that appear in the electronic side of the system.
Sources
- Brake Fluid Basics. Rob Krider, NASA Speed News, 1 November 2012. Hygroscopic behaviour, boiling points by DOT grade, compatibility and change intervals. Accessed 2026-11-19.