Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Renault Tuning
Parent
Section level
Applies to
Sagem S3000
Tool groups
None
Manufacturers
Renault

Changes from revision 1 to revision 3

Removed text is struck through; added text is highlighted.

SummaryFor the turbocharged Megane II RS 225 and R26 (Sagem S3000), the clutch is the component most often named as the first limit on a remap, followed by the stock intercooler and turbo. The evidence is mostly anecdotal and some of it concerns other Megane generations, which is noted where it applies. No logged boost data for a remapped 225 has been found. This page supplements F4R and F4RT Sagem remap expectations; the upgrade sequence is on exhaust, downpipe and turbo upgrade path.Condition checks before mappingBuying guides are the best available guide to what should be sound before extra torque is requested:Cambelt and auxiliary belt: evo advises confirming replacement at about 72,000 miles because a failure can destroy the engine, with the job costing over £1,000 at a dealer. Check service stamps and oil grade (semi-synthetic 5W-30 for road use). Fuel: use 98 RON; cheaper fuel can cause pinking. Engine wear and remaps: a specialist quoted by Fast Car links piston ring land failure to causes including failing injectors and bad remaps, and calls thermostat failures extremely common. Clutch and gearbox: the clutch should last past 60,000 miles; a sloppy shift suggests abuse. The R26's limited-slip differential has held up well. Brakes and suspension: Brembo discs wear faster than expected (budget for discs about every 20,000 miles with standard pads), and bushes begin to knock around 60,000 miles. Trophy and Cup cars received front springs about 25% stiffer and rear springs about 77% firmer than the original 225 with revised damping. Evidence of earlier tuning: evo notes to check for chipping or tuning, since an unknown map is a risk.ScopeThis adds forum and vendor evidence to F4R and F4RT Sagem remap expectations for the turbocharged Megane II RS 225 and R26 (Sagem S3000). Most of it is anecdotal and several sources concern other Megane generations; where so, it is stated.

Clutch

The prevailing view is that the standard clutch loses holding capacity before the software becomes the limit, but experience varies widely.One account has a car at about 280 hp on a dyno with the clutch still fine after 40,000 km, and another reports a stock clutch lasting 96,000 miles. Both are old and anecdotal. The dual-mass flywheel is not generally regarded as a problem while it remains original; owners who prefer a single-mass flywheel are mostly those who have fitted one. K-Tec sells organic and cerametallic kits for the 225, R26 and R26.R, claiming 35% more torque holding for the organic kit. Fitment depends on the flywheel on the car, and 225, R26 and R26.R pressure plates and flywheels are not interchangeable. A SEAT Cupra owner reports that some remaps deliver power less aggressively to avoid clutch slip. That is another model and is only an anecdote.A Digital Kaos thread (reached only through search summary; the page itself returned 403) argues the stock clutch loses holding ability before software is the limit, while one poster reports a car on a dyno at about 280 hp with the clutch fine after 40,000 km. It is old and anecdotal. An RSM forum poster reports a stock clutch lasting 96,000 miles and says the dual mass flywheel is not a problem if it has not been replaced, while those who prefer a single mass flywheel are the ones who fitted one. K-Tec sells organic and cerametallic kits for the 225, R26 and R26.R, claiming 35% more torque holding for the organic kit. Fitment depends on the flywheel on the car, and 225, R26 and R26.R pressure plates and flywheels are not interchangeable. A SEAT Cupra forum poster says some remaps deliver power less aggressively so the clutch does not slip. That is another model's forum and only an anecdote.

Turbo, intercooler and fuel

A tuning guide written for the Mk3 RS250 states that the stock turbo is good for about 320 bhp and that the standard intercooler restricts flow as boost rises. Its applicability to the Mk2 is unchecked. A generic F4Rt page lists a Mitsubishi twin-scroll turbo for the F4Rt family and cautions that the airflow sensor can restrict torque on larger builds. It gives no boost figure and is not specific to the Sagem car.Boost dataNo logged boost for a remapped 225 has been found. The only measured boost is from a Megane 3 RS265 owner thread: about 1.3 bar in 4th and 5th gear on the RS Monitor and OBD, about 1 bar in normal mode, and a dyno result of 253 hp and 393 Nm at around 30 °C. The owner concluded the car was unmapped. That thread says nothing about the 225 or its ECU. For the Mk2 car the Renault service text summarised on the S3000 page remains the only boost reference: a baseline of about 1,350 to 1,400 mbar and a stated 1,800 mbar ceiling.Claimed gainsClaimSource typeNote Stage 1: +30 bhp and +60 Nm (225 to 255 bhp, 300 to 360 Nm)Tuner pagesNot dyno-verified Stage 2: about +47 hp and +82 NmOne chiptuning resellerCompression ratio quoted as 9.0:1 Level 1: 240 to 250 bhp, about 270 lb ftOne UK dyno shopDepends on modifications R26 build at 273 bhp and 300 lb ft (torque capped)Single forum buildOne carNot establishedNo confirmed turbo failures on remapped 225s have been found, and there is no logged boost for the 225 on a remap.One tuning guide (fastcar.co.uk, written for the Mk3 RS250) says the stock turbo is good for around 320 bhp and the standard intercooler restricts flow as boost rises. Check applicability to the Mk2 before relying on it. A generic F4Rt page lists a Mitsubishi twin-scroll turbo for the F4Rt family, and cautions that the airflow sensor can restrict torque on bigger builds. It states no boost figure, and it is a generic page, not Sagem-specific.Logged boost: nothing for the 225The only boost data I found is an RSM forum thread on a Megane 3 RS265 (not the 225): about 1.3 bar in 4th and 5th gear on the RS Monitor and OBD, about 1 bar in normal mode, and a dyno result of 253 hp and 393 Nm at around 30 C. The poster concluded the car was unmapped. The thread says nothing about the 225 or its ECU. For the Mk2 car, the Renault service text on the S3000 page remains the only boost reference: about 1350 to 1400 mbar baseline and a stated 1800 mbar ceiling.Claims to treat carefullyClaimSource typeNote Stage 1: +30 bhp and +60 Nm (225 to 255 bhp, 300 to 360 Nm)Tuner pagesNot dyno-verified Stage 2: about +47 hp and +82 NmOne chiptuning resellerCompression ratio quoted as 9.0:1 Level 1: 240 to 250 bhp, about 270 lb ftOne UK dyno shopDepends on modifications R26 build at 273 bhp and 300 lb ft (torque capped)Forum buildSingle carI found no confirmed turbo failures on remapped 225s and no logged boost data for the 225 on a remap. Treat those as open questions.

Sources

evo: Renaultsport Megane checkpoints, accessed 2026-11-19. PistonHeads: Renaultsport Megane 2 buying guide (rolling chassis section), accessed 2026-11-19. fastcar.co.uk: Megane RS buyers guide, via search summary 2026-11-19. Digital Kaos: Megane 2.0t 225 sagem 3000, search summary only 2026-11-19 (page returned 403). RSMegane: Quick question (Megane 3 RS265), accessed 2026-11-19. RSMegane: 225 new clutch discussion, search summary only 2026-11-19. K-Tec Racing: RTS clutch kits for Megane 2RS 225 / R26, search summary 2026-11-19. fastcar.co.uk: Megane RS250 tuning guide, search summary only 2026-11-19. TorqueCars: Renault F4Rt tuning, accessed 2026-11-19. Chiptuningreseller: Megane 2 RS 2.0T, search summary 2026-11-19.Digital Kaos: Megane 2.0t 225 sagem 3000, search summary only 2026-11-19. RSMegane: Quick question (Megane 3 RS265), accessed 2026-11-19. RSMegane: 225 new clutch discussion, search summary only 2026-11-19. K-Tec Racing: RTS clutch kits for Megane 2RS 225 / R26, search summary 2026-11-19. fastcar.co.uk: Megane RS250 tuning guide, search summary only 2026-11-19. TorqueCars: Renault F4Rt tuning, accessed 2026-11-19. Chiptuningreseller: Megane 2 RS 2.0T, search summary 2026-11-19.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Megane II RS 225 F4RT remap: clutch, turbo and supporting limits

Scope

This adds forum and vendor evidence to F4R and F4RT Sagem remap expectations for the turbocharged Megane II RS 225 and R26 (Sagem S3000). Most of it is anecdotal and several sources concern other Megane generations; where so, it is stated.

Clutch

  • A Digital Kaos thread (reached only through search summary; the page itself returned 403) argues the stock clutch loses holding ability before software is the limit, while one poster reports a car on a dyno at about 280 hp with the clutch fine after 40,000 km. It is old and anecdotal.
  • An RSM forum poster reports a stock clutch lasting 96,000 miles and says the dual mass flywheel is not a problem if it has not been replaced, while those who prefer a single mass flywheel are the ones who fitted one.
  • K-Tec sells organic and cerametallic kits for the 225, R26 and R26.R, claiming 35% more torque holding for the organic kit. Fitment depends on the flywheel on the car, and 225, R26 and R26.R pressure plates and flywheels are not interchangeable.
  • A SEAT Cupra forum poster says some remaps deliver power less aggressively so the clutch does not slip. That is another model's forum and only an anecdote.

Turbo, intercooler and fuel

  • One tuning guide (fastcar.co.uk, written for the Mk3 RS250) says the stock turbo is good for around 320 bhp and the standard intercooler restricts flow as boost rises. Check applicability to the Mk2 before relying on it.
  • A generic F4Rt page lists a Mitsubishi twin-scroll turbo for the F4Rt family, and cautions that the airflow sensor can restrict torque on bigger builds. It states no boost figure, and it is a generic page, not Sagem-specific.

Logged boost: nothing for the 225

The only boost data I found is an RSM forum thread on a Megane 3 RS265 (not the 225): about 1.3 bar in 4th and 5th gear on the RS Monitor and OBD, about 1 bar in normal mode, and a dyno result of 253 hp and 393 Nm at around 30 C. The poster concluded the car was unmapped. The thread says nothing about the 225 or its ECU. For the Mk2 car, the Renault service text on the S3000 page remains the only boost reference: about 1350 to 1400 mbar baseline and a stated 1800 mbar ceiling.

Claims to treat carefully

ClaimSource typeNote
Stage 1: +30 bhp and +60 Nm (225 to 255 bhp, 300 to 360 Nm)Tuner pagesNot dyno-verified
Stage 2: about +47 hp and +82 NmOne chiptuning resellerCompression ratio quoted as 9.0:1
Level 1: 240 to 250 bhp, about 270 lb ftOne UK dyno shopDepends on modifications
R26 build at 273 bhp and 300 lb ft (torque capped)Forum buildSingle car

I found no confirmed turbo failures on remapped 225s and no logged boost data for the 225 on a remap. Treat those as open questions.

Sources

Revision 3: Megane II RS 225 F4RT remap: clutch, turbo and supporting limits

Summary

For the turbocharged Megane II RS 225 and R26 (Sagem S3000), the clutch is the component most often named as the first limit on a remap, followed by the stock intercooler and turbo. The evidence is mostly anecdotal and some of it concerns other Megane generations, which is noted where it applies. No logged boost data for a remapped 225 has been found. This page supplements F4R and F4RT Sagem remap expectations; the upgrade sequence is on exhaust, downpipe and turbo upgrade path.

Condition checks before mapping

Buying guides are the best available guide to what should be sound before extra torque is requested:

  • Cambelt and auxiliary belt: evo advises confirming replacement at about 72,000 miles because a failure can destroy the engine, with the job costing over £1,000 at a dealer. Check service stamps and oil grade (semi-synthetic 5W-30 for road use).
  • Fuel: use 98 RON; cheaper fuel can cause pinking.
  • Engine wear and remaps: a specialist quoted by Fast Car links piston ring land failure to causes including failing injectors and bad remaps, and calls thermostat failures extremely common.
  • Clutch and gearbox: the clutch should last past 60,000 miles; a sloppy shift suggests abuse. The R26's limited-slip differential has held up well.
  • Brakes and suspension: Brembo discs wear faster than expected (budget for discs about every 20,000 miles with standard pads), and bushes begin to knock around 60,000 miles. Trophy and Cup cars received front springs about 25% stiffer and rear springs about 77% firmer than the original 225 with revised damping.
  • Evidence of earlier tuning: evo notes to check for chipping or tuning, since an unknown map is a risk.

Clutch

The prevailing view is that the standard clutch loses holding capacity before the software becomes the limit, but experience varies widely.

  • One account has a car at about 280 hp on a dyno with the clutch still fine after 40,000 km, and another reports a stock clutch lasting 96,000 miles. Both are old and anecdotal.
  • The dual-mass flywheel is not generally regarded as a problem while it remains original; owners who prefer a single-mass flywheel are mostly those who have fitted one.
  • K-Tec sells organic and cerametallic kits for the 225, R26 and R26.R, claiming 35% more torque holding for the organic kit. Fitment depends on the flywheel on the car, and 225, R26 and R26.R pressure plates and flywheels are not interchangeable.
  • A SEAT Cupra owner reports that some remaps deliver power less aggressively to avoid clutch slip. That is another model and is only an anecdote.

Turbo, intercooler and fuel

  • A tuning guide written for the Mk3 RS250 states that the stock turbo is good for about 320 bhp and that the standard intercooler restricts flow as boost rises. Its applicability to the Mk2 is unchecked.
  • A generic F4Rt page lists a Mitsubishi twin-scroll turbo for the F4Rt family and cautions that the airflow sensor can restrict torque on larger builds. It gives no boost figure and is not specific to the Sagem car.

Boost data

No logged boost for a remapped 225 has been found. The only measured boost is from a Megane 3 RS265 owner thread: about 1.3 bar in 4th and 5th gear on the RS Monitor and OBD, about 1 bar in normal mode, and a dyno result of 253 hp and 393 Nm at around 30 °C. The owner concluded the car was unmapped. That thread says nothing about the 225 or its ECU. For the Mk2 car the Renault service text summarised on the S3000 page remains the only boost reference: a baseline of about 1,350 to 1,400 mbar and a stated 1,800 mbar ceiling.

Claimed gains

ClaimSource typeNote
Stage 1: +30 bhp and +60 Nm (225 to 255 bhp, 300 to 360 Nm)Tuner pagesNot dyno-verified
Stage 2: about +47 hp and +82 NmOne chiptuning resellerCompression ratio quoted as 9.0:1
Level 1: 240 to 250 bhp, about 270 lb ftOne UK dyno shopDepends on modifications
R26 build at 273 bhp and 300 lb ft (torque capped)Single forum buildOne car

Not established

No confirmed turbo failures on remapped 225s have been found, and there is no logged boost for the 225 on a remap.

Sources