Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Modded Cars
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Toyota

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

This is a white Toyota GR Yaris, bought in April 2021 and initially run with a DTUK Stage 2 module and breathing modifications. A later Litchfield build and mapping session produced approximately 380 bhp and 450 Nm (owner-reported; a Litchfield printout was posted by the owner).SayonaraLicense bought this white GR Yaris in April 2021 and initially used a DTUK Stage 2 module with breathing modifications. A later Litchfield build and mapping session produced approximately 380 bhp and 450 Nm, according to the owner. Owner’s introduction and specification

Engine and calibration

The build uses Kelford A-profile camshafts, springs and retainers, an HKS head gasket, Lamspeed H13 head studs and Syvecs management. The original turbo is retained. A Wagner intercooler, charge pipes and turbo elbow complement an Eventuri intake and C-Tech three-inch exhaust.The build used Kelford A-profile camshafts, springs and retainers, an HKS head gasket, Lamspeed H13 head studs and Syvecs management. The owner retained the original turbo for this setup. A Wagner intercooler, charge pipes and turbo elbow complemented an Eventuri intake and C-Tech three-inch exhaust. Engine and intake specification · Camshaft and valvetrain installation photos

The owner says SRD Tuning remapped the car in August 2023. The 380 bhp figure belongs to the earlier Litchfield session, not to the SRD remap.Chassis and interiorEibach springs and camber bolts, wheel spacers and a fast-road alignment form part of the chassis setup. Later additions are Recaro Profi SPG seats on Cobra bases, and the owner lists Powerflex engine and gearbox mounts.Chassis and later updatesEibach springs and camber bolts, wheel spacers and a fast-road alignment formed part of the chassis setup. The owner later fitted Recaro Profi SPG seats on Cobra bases and listed Powerflex engine and gearbox mounts. Seat installation · Updated equipment list

Photos by SayonaraLicense, reproduced with permission.SourcesGR-Zoo build thread: introduction, engine and intake specificationGR-Zoo build thread: camshaft and valvetrain installation photosGR-Zoo build thread: seat installationGR-Zoo build thread: updated equipment listGR-Zoo build thread: Litchfield printout and mapping chronologyGR-Zoo build thread: reason for the later remapThe owner says SRD Tuning remapped the car in August 2023. The 380 bhp figure belongs to the earlier Litchfield session, whose printout was posted alongside that update. Photos by SayonaraLicense, reproduced with permission. Litchfield printout and mapping chronology · Reason for the later remap

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: SayonaraLicense’s 380 bhp Toyota GR Yaris

SayonaraLicense bought this white GR Yaris in April 2021 and initially used a DTUK Stage 2 module with breathing modifications. A later Litchfield build and mapping session produced approximately 380 bhp and 450 Nm, according to the owner. Owner’s introduction and specification

SayonaraLicense’s white Toyota GR Yaris on a country road

Engine and calibration

The build used Kelford A-profile camshafts, springs and retainers, an HKS head gasket, Lamspeed H13 head studs and Syvecs management. The owner retained the original turbo for this setup. A Wagner intercooler, charge pipes and turbo elbow complemented an Eventuri intake and C-Tech three-inch exhaust. Engine and intake specification · Camshaft and valvetrain installation photos

GR Yaris cylinder head during the camshaft and valvetrain work

Chassis and later updates

Eibach springs and camber bolts, wheel spacers and a fast-road alignment formed part of the chassis setup. The owner later fitted Recaro Profi SPG seats on Cobra bases and listed Powerflex engine and gearbox mounts. Seat installation · Updated equipment list

Recaro bucket seat installed in the GR Yaris

The owner says SRD Tuning remapped the car in August 2023. The 380 bhp figure belongs to the earlier Litchfield session, whose printout was posted alongside that update. Photos by SayonaraLicense, reproduced with permission. Litchfield printout and mapping chronology · Reason for the later remap

Revision 2: SayonaraLicense’s 380 bhp Toyota GR Yaris

This is a white Toyota GR Yaris, bought in April 2021 and initially run with a DTUK Stage 2 module and breathing modifications. A later Litchfield build and mapping session produced approximately 380 bhp and 450 Nm (owner-reported; a Litchfield printout was posted by the owner).

SayonaraLicense’s white Toyota GR Yaris on a country road

Engine and calibration

The build uses Kelford A-profile camshafts, springs and retainers, an HKS head gasket, Lamspeed H13 head studs and Syvecs management. The original turbo is retained. A Wagner intercooler, charge pipes and turbo elbow complement an Eventuri intake and C-Tech three-inch exhaust.

GR Yaris cylinder head during the camshaft and valvetrain work

The owner says SRD Tuning remapped the car in August 2023. The 380 bhp figure belongs to the earlier Litchfield session, not to the SRD remap.

Chassis and interior

Eibach springs and camber bolts, wheel spacers and a fast-road alignment form part of the chassis setup. Later additions are Recaro Profi SPG seats on Cobra bases, and the owner lists Powerflex engine and gearbox mounts.

Recaro bucket seat installed in the GR Yaris

Photos by SayonaraLicense, reproduced with permission.

Sources