Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Modded Cars
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Alfa Romeo

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

TheStig's Alfa Romeo MiTo is a 135 CV 1.4 MultiAir Distinctive, bought new in October 2009 by its owner Alessio, and converted with a Garrett 1446 turbo. Seven years later it gained 305 mm Brembo brakes, a reinforced clutch and a direct intake. The owner reports a dyno result of about 200 CV and just over 300 Nm (owner-reported, single source).

Turbo and chassis

The first build list paired a Garrett 1446 turbo with a larger Orra Racing intercooler, a Brain 200-cell catalyst in the downpipe, a Ragazzon rear exhaust section and Serial Tuning engine calibration. The chassis ran Eibach springs, 12 mm spacers front and rear, and drilled Zimmermann front discs.Seven-year updateBrakes were upgraded to 305 mm discs with four-piston Brembo calipers, braided lines and Roesch XC4 pads. A reinforced Fiorentini clutch was fitted and the panel filter was replaced with an MTD direct intake. The owner-reported dyno result was about 200 CV and just over 300 Nm.Alessio, posting as TheStig, bought this 135 CV MultiAir Distinctive new in October 2009. His first build list paired a Garrett 1446 turbo with a larger Orra Racing intercooler, a Brain 200-cell catalyst in the downpipe, a Ragazzon rear exhaust section and Serial Tuning engine calibration. The chassis ran Eibach springs, 12 mm spacers front and rear, and drilled Zimmermann front discs.Seven years laterAlessio returned to document 305 mm brakes with four-piston Brembo calipers, braided lines and Roesch XC4 pads. He also fitted a reinforced Fiorentini clutch and replaced the panel filter with an MTD direct intake. The owner reported that the car produced about 200 CV and just over 300 Nm on a dyno.

Photographs by TheStig, reproduced with permission from the ClubAlfa.it posts linked below.

SourcesClubAlfa.it build thread: original turbo and chassis buildClubAlfa.it build thread: seven-year update with brakes, intake, clutch and dyno figuresOwner’s postsAlessio’s original turbo and chassis buildSeven-year update with brakes, intake, clutch and dyno figures

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: TheStig’s Garrett 1446 Alfa Romeo MiTo 1.4 MultiAir

Turbo and chassis

Alessio, posting as TheStig, bought this 135 CV MultiAir Distinctive new in October 2009. His first build list paired a Garrett 1446 turbo with a larger Orra Racing intercooler, a Brain 200-cell catalyst in the downpipe, a Ragazzon rear exhaust section and Serial Tuning engine calibration. The chassis ran Eibach springs, 12 mm spacers front and rear, and drilled Zimmermann front discs.

Seven years later

Alessio returned to document 305 mm brakes with four-piston Brembo calipers, braided lines and Roesch XC4 pads. He also fitted a reinforced Fiorentini clutch and replaced the panel filter with an MTD direct intake. The owner reported that the car produced about 200 CV and just over 300 Nm on a dyno.

Alessio’s red MiTo in the original build post

The red MiTo photographed for Alessio’s seven-year update

Photographs by TheStig, reproduced with permission from the ClubAlfa.it posts linked below.

Owner’s posts

Revision 2: TheStig’s Garrett 1446 Alfa Romeo MiTo 1.4 MultiAir

TheStig's Alfa Romeo MiTo is a 135 CV 1.4 MultiAir Distinctive, bought new in October 2009 by its owner Alessio, and converted with a Garrett 1446 turbo. Seven years later it gained 305 mm Brembo brakes, a reinforced clutch and a direct intake. The owner reports a dyno result of about 200 CV and just over 300 Nm (owner-reported, single source).

Turbo and chassis

The first build list paired a Garrett 1446 turbo with a larger Orra Racing intercooler, a Brain 200-cell catalyst in the downpipe, a Ragazzon rear exhaust section and Serial Tuning engine calibration. The chassis ran Eibach springs, 12 mm spacers front and rear, and drilled Zimmermann front discs.

Seven-year update

Brakes were upgraded to 305 mm discs with four-piston Brembo calipers, braided lines and Roesch XC4 pads. A reinforced Fiorentini clutch was fitted and the panel filter was replaced with an MTD direct intake. The owner-reported dyno result was about 200 CV and just over 300 Nm.

Alessio’s red MiTo in the original build post

The red MiTo photographed for Alessio’s seven-year update

Photographs by TheStig, reproduced with permission from the ClubAlfa.it posts linked below.

Sources