Page organisation in this revision
- Page type
- Technical article
- Subject
- Modded Cars
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- BMW, Jeep
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
This is a 1988 Jeep Comanche pickup rebuilt with a BMW M57N diesel engine driving the Jeep AW4 automatic transmission through an adaptor. The engine was collected in March 2024, trial-fitted and then installed with fabrication and wiring work.Comanche Club member colthrax documented rebuilding a 1988 Jeep Comanche and fitting a BMW M57N diesel. In March 2024 the builder collected the engine and recorded the trial fit, fabrication and wiring in a multi-page diary. Read the engine swap diary.The M57 during trial fitting in March 2024. Photograph by colthrax, reproduced with permission.
Engine and transmission
An adaptor joins the M57 to the Jeep AW4 gearbox. The owner describes a sequential shift arrangement using an Arduino and NiftyShifter, built while working out the throttle signal needed by the automatic transmission controller. Cooling combines the M57 mechanical fan with a Jeep 2.5 diesel radiator and fan shroud.The build uses an adaptor between the M57 and Jeep AW4 gearbox. In the May 2024 owner profile, the builder describes a sequential shift arrangement using an Arduino and NiftyShifter while working out the throttle signal needed by the automatic transmission controller. Cooling combines the M57 mechanical fan with a Jeep 2.5 diesel radiator and fan shroud. Read the owner’s build profile.The later installation, shared in the Comanche Club owner profile. Photograph by colthrax, reproduced with permission.
Browse more M57 4×4 builds and the BMW M57 engine guide.
SourcesComanche Club build thread: M57 engine swap, trial fit, fabrication and wiring (March 2024)Comanche Club owner profile (May 2024): shift control and cooling
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Colthrax’s M57 Jeep Comanche pickup
Comanche Club member colthrax documented rebuilding a 1988 Jeep Comanche and fitting a BMW M57N diesel. In March 2024 the builder collected the engine and recorded the trial fit, fabrication and wiring in a multi-page diary. Read the engine swap diary.

The M57 during trial fitting in March 2024. Photograph by colthrax, reproduced with permission.
Engine and transmission
The build uses an adaptor between the M57 and Jeep AW4 gearbox. In the May 2024 owner profile, the builder describes a sequential shift arrangement using an Arduino and NiftyShifter while working out the throttle signal needed by the automatic transmission controller. Cooling combines the M57 mechanical fan with a Jeep 2.5 diesel radiator and fan shroud. Read the owner’s build profile.

The later installation, shared in the Comanche Club owner profile. Photograph by colthrax, reproduced with permission.
Browse more M57 4×4 builds and the BMW M57 engine guide.
Revision 2: Colthrax’s M57 Jeep Comanche pickup
This is a 1988 Jeep Comanche pickup rebuilt with a BMW M57N diesel engine driving the Jeep AW4 automatic transmission through an adaptor. The engine was collected in March 2024, trial-fitted and then installed with fabrication and wiring work.

The M57 during trial fitting in March 2024. Photograph by colthrax, reproduced with permission.
Engine and transmission
An adaptor joins the M57 to the Jeep AW4 gearbox. The owner describes a sequential shift arrangement using an Arduino and NiftyShifter, built while working out the throttle signal needed by the automatic transmission controller. Cooling combines the M57 mechanical fan with a Jeep 2.5 diesel radiator and fan shroud.

The later installation, shared in the Comanche Club owner profile. Photograph by colthrax, reproduced with permission.
Browse more M57 4×4 builds and the BMW M57 engine guide.
Sources