Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Injectors
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
BMW

The M57 family uses Bosch common-rail injectors, but the injector actuator changes by engine version. The original M57 and first technical update use electromagnetic solenoid injectors. The later M57TU2 high-output OL and twin-turbo TOP use piezoelectric injectors. The lower-output 3.0-litre TU2 UL is the important exception: examples are listed with solenoid injectors, although some broad parts catalogues conflict. Always identify the actual engine, VIN and fitted injector number.

“Mk1”, “Mk2” and “Mk3” are informal workshop labels used here for the original M57, M57TU/M57N and M57TU2/M57N2. They are not BMW's complete engine codes. A 325d or 525d badge alone does not establish a 2.5-litre engine: some later 25d-badged M57s displace 2,993 cc. BMW training describes the original M57 solenoid injector, the M57TU solenoid injector and a 730d M57TU2 piezo system.

Injector type by generation and engine

Workshop generationEngine / outputTypical applicationsInjector actuatorEvidence and limits
Mk1: original M57M57D25, 2,497 cc; 110/120 kWE39 525d 120 kW; Opel Omega 2.5 DTI 110 kWSolenoidBMW original-M57 training describes a solenoid actuator. Bosch 0 445 110 048 is a separately catalogued E39 525d example; do not assume the Opel uses that same part number.
Mk1: original M57M57D30, 2,926 cc; 135/142 kW examplesE39 530d, E46 330d, E38 730d, E53 X5 3.0d in corresponding versionsSolenoidOriginal-generation M57 common rail; Bosch 0 445 110 047 is a listed example for selected applications, not all engines.
Mk2: M57TU / M57NM57D25TU, 2,497 cc; 120/130 kWE60/E61 525d 2.5SolenoidSecond-generation common-rail family. Confirm build and injector number; an injector from a different 2.5 or 3.0 variant is not automatically compatible.
Mk2: M57TU / M57NM57D30TU, 2,993 cc; 150/160 kW examplesE46 330d, E60/E61 530d and other specified 3.0d modelsSolenoidBMW M57TU training explicitly shows a solenoid-operated injector. 0 445 110 131 and 0 445 110 216 are separately listed examples; confirm by VIN.
Mk2: M57TU TOPM57D30TU TOP, 2,993 cc; 200 kW / 272 PSEarly E60/E61 535d twin turboSolenoidBosch 0 445 110 219 is an example identified by a diesel specialist for 2004–07 535d 200 kW. It is not the same actuator type as the later 210 kW 535d.
Mk3: M57TU2 ULM57D30TU2 UL, 2,993 cc; 145 kW / 197 PSSelected E90/E91 325d and E60/E61 525dSolenoid in documented examples; verify the individual carInjector specialist catalogues list Bosch 0 445 110 209 on selected 325d/525d, and an E91 325d M57 306D3 dismantled example is recorded with it. Some broad catalogues list piezo references under the same 325d heading, so engine code, production date and installed part number take precedence; do not treat this row as proof for every market or replacement engine.
Mk3: M57TU2 OLM57D30TU2 OL, 2,993 cc; 170/173 kW examplesSelected E90/E91 330d, E60/E61 530d, E65 730d and E70 X5 3.0dPiezoBMW specifically documents piezo injectors for the 170 kW M57TU2 730d. Verify each individual model and part number.
Mk3: M57TU2 TOPM57D30TU2 TOP, 2,993 cc; 210 kW / 286 PS European specificationM57 335d, later E60/E61 535d, X5 3.0sd/xDrive35d and X6 xDrive35dPiezoBMW identifies piezo injectors in the US M57D30T2 Advanced Diesel. European M57TU2 TOP examples also use piezo. US 335d/X5 ratings differ from European ones.

There is no separately established 2,497 cc M57D25TU2 row in this guide. Distinguish the genuine 2.5-litre M57D25/TU from the later 2,993 cc 325d/525d UL before ordering.

Injector-number examples

Bosch numberActuatorDocumented example, not a universal fit
0 445 110 048Solenoid, CRI1E39 525d 2.5 M57D25 120 kW; diesel specialist application.
0 445 110 047SolenoidSelected original M57 3.0 applications, including E39/E46 examples; injector catalogue and BMW original-engine training. Check the individual part.
0 445 110 219Solenoid, CRI2E60/E61 535d 200 kW / 272 PS; specialist injector and application listing.
0 445 110 209SolenoidListed for selected 325d/525d applications, including an identified 145 kW E91 M57 example. Injector family and part listing; dismantled E91 example. An aftermarket dismantled part is not conclusive proof of original factory fitment.
0 445 115 077PiezoSold for specified M57N2 330d/335d and related applications; see Darkside's application listing. Check BMW and Bosch supersession for the actual VIN.

References shown are examples from the listed sources, not a complete interchange list. Manufacturer supersessions, emissions version, coding and previous engine or cylinder-head swaps can change what is actually installed. The number suffix alone is not proof of fitment, nozzle flow or power capability.

Solenoid and piezo: practical differences

A solenoid injector uses an electromagnetic valve to control the hydraulic forces acting on its nozzle needle. A piezo injector uses a piezoelectric actuator and hydraulic control arrangement. Both operate in a high-pressure common-rail system and require the matched DDE driver, harness, injector configuration and calibration. Quicker actuator response can support multiple injection events, but does not make all piezo injectors interchangeable or automatically higher-flowing. BMW service information on M57TU2 piezo injectors.

Manifold and swirl flaps when identifying injectors

The intake manifold and injector system are related to combustion but are separate identifiers. M57 cylinders have separate swirl and tangential inlet ports; where fitted, a manifold flap controls the tangential runner. At selected low-load conditions the DDE restricts that route to favour the swirl-forming passage, then opens it as operating conditions require. The DDE may control flap movement using vacuum or an electric actuator, depending on the application. BMW M57TU training; M57TU TOP vacuum schematic.

Do not identify a 2.5-litre or 3.0-litre engine, solenoid/piezo injector, or its calibration solely by the shape of the manifold or whether it has swirl flaps. Manifold and head versions can differ, parts may have been replaced, and published fitment claims for some 145 kW 325d/525d versions conflict. Record the engine code, VIN, full injector number, manifold part number and actual hardware. For the two very different inlet routes, flap operation, deposits and inspection, see M57 inlet-port and swirl-flap guide.

When removing the manifold for injector or glow-plug work, mark all electrical and vacuum connections, protect open inlet ports against debris and follow the exact procedure for cleaning and new seals. A loose or missing flap or fastener requires investigation before running the engine. BMW's M57Y 335d intake-cleaning bulletin gives model-specific photographs and service steps.

Identification, diagnosis and upgrades

  • Record the VIN, build date, market, engine code, DDE version and full Bosch/BMW injector number. If the engine, head or injectors have been changed, inspect the installed hardware; catalogue the actual engine alongside the chassis.
  • Use the vehicle-specific diagnostic procedure for correction values, rail pressure, return flow and electrical faults. A high correction value or return-flow result alone does not necessarily condemn one injector; compression, air and fuel supply can affect the result.
  • Injector individual correction or calibration codes and adaptation procedures vary by system. Enter the supplied code in the correct cylinder when required, following the DDE service procedure; do not assume that all generations use the same coding scheme.
  • Solenoid and piezo units have different drive requirements and may differ in mounting and hydraulic characteristics. A solenoid 272 PS 535d injector is not a plug-in replacement for a piezo 286 PS 335d injector. Verify mechanical fit, nozzle and spray pattern, rail system, DDE driver and a calibration developed for the combination. Do not apply battery voltage directly to a piezo injector.
  • Upgraded nozzles or injectors should be assembled and flow-tested by an appropriate diesel specialist. Size the pump and low-pressure supply, turbo airflow, cooling and calibration together; quoted percentages and power claims depend on test conditions.
  • Common-rail fuel can remain at high pressure after shutdown. Follow the specified depressurisation, cleanliness and high-pressure-line replacement procedure. Never loosen a live high-pressure line or check for a leak with a hand.

Related: BMW M57 engines, M57 twin-turbo upgrades and fuelling fault diagnosis.