Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Flash chips
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
AMD, Case, Sisu

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

AMD's Am29F040B is a 4 Mbit parallel NOR flash organised as 512K × 8 (512 KiB). The AMD datasheet specifies a single 5 V supply for read and write and eight uniform 64 KiB sectors. Its 32-pin package options include PLCC, TSOP and PDIP; the complete order code determines the package, speed and temperature range.

Reported controller applications

An Engine Coders service listing identifies AM29F040 with a Case EEM2 controller labelled EEM-S002, 5533710 and 3799306. That listing does not establish the full chip suffix or that every EEM2 board uses this part. Separately, ECUfile's procedure catalogue names 29F040 flash in its SISU EMM engine-controller entry without specifying a manufacturer or suffix. Treat these as service listings and confirm the marking on the actual board.

Identification and programming

Do not confuse the byte-wide 29F040 with the 29F400 boot-block family: both have 4 Mbit nominal capacity, but the Am29F040B is organised ×8 with uniform 64 KiB sectors, while the Am29F400B supports byte or word organisation and has a different boot-block sector map. Capacity alone does not establish interchangeability.

The exact part marking, package pinout, operating temperature, sector layout and programmer algorithm should be checked against the board and datasheet. A full device read is nominally 512 KiB; a diagnostic calibration file may cover a different range. Record the read method and preserve the original data.

Related: EPROM-pinout flash.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Am29F040 flash in engine controllers

AMD's Am29F040B is a 4 Mbit parallel NOR flash organised as 512K × 8 (512 KiB). The AMD datasheet specifies a single 5 V supply for read and write and eight uniform 64 KiB sectors. Its 32-pin package options include PLCC, TSOP and PDIP; the complete order code determines the package, speed and temperature range.

Reported controller applications

An Engine Coders service listing identifies AM29F040 with a Case EEM2 controller labelled EEM-S002, 5533710 and 3799306. That listing does not establish the full chip suffix or that every EEM2 board uses this part. Separately, ECUfile's procedure catalogue names 29F040 flash in its SISU EMM engine-controller entry without specifying a manufacturer or suffix. Treat these as service listings and confirm the marking on the actual board.

Identification and programming

Do not confuse the byte-wide 29F040 with the 29F400 boot-block family: both have 4 Mbit nominal capacity, but the Am29F040B is organised ×8 with uniform 64 KiB sectors, while the Am29F400B supports byte or word organisation and has a different boot-block sector map. Capacity alone does not establish interchangeability.

The exact part marking, package pinout, operating temperature, sector layout and programmer algorithm should be checked against the board and datasheet. A full device read is nominally 512 KiB; a diagnostic calibration file may cover a different range. Record the read method and preserve the original data.

Related: EPROM-pinout flash.

Revision 1: Am29F040 flash in engine controllers

AMD's Am29F040B is a 4 Mbit parallel NOR flash organised as 512K × 8 (512 KiB). The AMD datasheet specifies a single 5 V supply for read and write and eight uniform 64 KiB sectors. Its 32-pin package options include PLCC, TSOP and PDIP; the complete order code determines the package, speed and temperature range.

Reported controller applications

An Engine Coders service listing identifies AM29F040 with a Case EEM2 controller labelled EEM-S002, 5533710 and 3799306. That listing does not establish the full chip suffix or that every EEM2 board uses this part. Separately, ECUfile's procedure catalogue names 29F040 flash in its SISU EMM engine-controller entry without specifying a manufacturer or suffix. Treat these as service listings and confirm the marking on the actual board.

Identification and programming

Do not confuse the byte-wide 29F040 with the 29F400 boot-block family: both have 4 Mbit nominal capacity, but the Am29F040B is organised ×8 with uniform 64 KiB sectors, while the Am29F400B supports byte or word organisation and has a different boot-block sector map. Capacity alone does not establish interchangeability.

The exact part marking, package pinout, operating temperature, sector layout and programmer algorithm should be checked against the board and datasheet. A full device read is nominally 512 KiB; a diagnostic calibration file may cover a different range. Record the read method and preserve the original data.

Related: EPROM-pinout flash.