Tuning Wiki

Engine swaps and standalone ECU conversions (using controllers such as ECUMaster EMU BLACK/PRO, MaxxECU, CANTCU, or Turbolamik) rely on emulating the exact OEM powertrain CAN frames expected by the transmission control unit (TCU) and gear selector (GWS). If mandatory engine torque/RPM frames or CRC-8 checksums are missing or invalid, modern TCUs will drop into limp mode or refuse to wake up.

BMW F-Series ZF 8HP (8HP45 / 8HP70 / 8HP75) PT-CAN IDs (500 kbit/s)

Compiled from BMW F10 8HP70 PT-CAN1/PT-CAN2 reverse engineering. Byte 0 on critical frames carries an SAE J1850 CRC-8 checksum and Byte 1 carries a rolling alive counter; if 0x0A5 is missing or has an invalid CRC, the 8HP TCU enters sleep/clicking fault mode.

Hex ID Decimal Sender → Receiver Cycle Role & Key Signals
0x0A5165DME → EGS (PT-CAN2)10 msCrankshaft Torque 1 (Mandatory Wake/Run): Byte 0 CRC-8, Byte 1 counter (0x10–0x1F), Engine & Gearbox torque (12b each, ×0.5 − 1023.5 Nm), Engine RPM = ((B6 << 8) | B5) / 4
0x0D9217DME → EGS10–20 msAccelerator pedal % & throttle position % (12-bit each, ÷40)
0x197407GWS → EGS—Gear selector lever position (P/R/N/D/M+/M− & Park button), CRC-8 + counter
0x19D413EGS → DME / DSC—Transmission Status 2 (engaged gear, shift in progress, torque reduction request)
0x1A6422DSC / EGS → GWS—Distance / expected by GWS shifter
0x202514FRM / EGS → GWS—Illumination / expected by GWS shifter
0x3F91017DME → Bus—Drivetrain data: Coolant temp (Byte 4: raw − 48 °C), Oil temp (Byte 5: raw − 48 °C), Gear & Max RPM
0x3FD1021EGS → GWS / Kombi—Transmission Status 1 (5 bytes: CRC-8, counter, P/R/N/D & M/S gear display)
0x55E / 0x65E1374 / 1630GWS → Bus—GWS network heartbeat (0x55E) & UDS diagnostics (0x65E)

BMW E-Series (E46 / E9x) EGS & DKG/DCT CAN IDs (500 kbit/s)

  • BMW E46 / E39 CAN11h (see BMW CAN11h IDs): 0x43F (1087) EGS1, 0x443 (1091) EGS2 (MS45), and 0x43D (1085) AMT1 (SMG); DME replies on 0x316 (RPM/torque), 0x329 (ECT/pedal/kickdown), and 0x545.
  • BMW E9x / E8x BN2000 EGS & M3 DKG/DCT (see BMW E9x IDs): 0x0B5 (181) Torque_request_EGS (gearbox temp Byte 7), 0x0BA (186) TransmissionData (target gear, shifting bit, gear ratio, output shaft speed), 0x1A2 (418) TransmissionData2 (manual mode), 0x1D2 (466) TransmissionDataDisplay (selector pos, actual gear, sport mode), 0x37D (893) Status_DKG, 0x3B1 (945) TransmissionData3 (DKG).

VAG DSG (PQ35/PQ46 & MQB) CAN IDs (500 kbit/s)

  • PQ35 / PQ46 (DQ250 / DQ500) (see VAG PQ IDs): 0x440 (1088) Getriebe_1 (shift active, torque converter, target gear, selector), 0x448 (1096) Waehlhebel_1 (shifter position), 0x540 (1344) Getriebe_2 (engaged gear & display — note: collides with MaxxECU Default CAN v1.3 0x540!).
  • MQB / MQB Evo (DQ250 / DQ381 / DQ500) (see VAG MQB IDs): 0x0AD (173) Getriebe_11 (target clutch torque, GE_Fahrstufe), 0x0AE (174) Getriebe_12 (synchro target RPM), 0x0AF (175) Waehlhebel_03 (shifter), 0x12D (301) Getriebe_13 (input shaft speed, limp-home flag), 0x394 (916) WBA_03 (selector & sailing mode), 0x3C8 (968) Getriebe_14 (launch control bit).

Sources