Scope. An electronic throttle body uses position feedback and an electrically driven plate. The ECU may learn or check positions during a service basic setting and during other operating phases. This guide concerns throttle-body actuator adaptation and its diagnosis, not pedal-response coding or the separate boost-actuator adaptation. The identifiers are examples from the community SC8S5031_C_OEM Simos 18.1 cross-reference; match ECU ASW/CAL, engine, throttle part, active branch and scan-tool definitions before applying them.
Adaptation, setpoint and pedal response are different
Ross-Tech's throttle-body alignment guide describes a motorised throttle being cycled through positions for relearning on many VW/Audi applications. Its listed prerequisites and group procedures cover multiple controller generations, so the current factory procedure and supported diagnostic function for the exact vehicle should be used; an older group number, voltage or temperature range is not a universal Simos 18 specification.
A throttle adaptation concerns position-system behaviour and checks, while pedal interpretation concerns how the driver requests torque. The ECU may deliberately command a partly open throttle even with high pedal input. Compare pedal request, final plate setpoint and actual feedback in context before judging a calibration. See throttle control and driver torque request.
SC8S5031 condition and timing examples
In the THRO adaptation application reference, the following are calibration scalars, not targets to copy. Their presence alone does not prove a function or selector is active in another ECU file:
c_n_max_tps_adis a maximum engine-speed condition in rpm;c_pv_max_tps_adis a maximum accelerator-pedal condition in percent;c_vs_max_tps_adis a maximum vehicle-speed condition in km/h. The actual conditions and diagnostic procedure can include additional checks.c_tco_min_tps_adandc_tco_max_tps_adare coolant-temperature conditions,c_tia_min_tps_adis an intake-air-temperature condition, andc_vb_min_tps_adis a battery-voltage condition. The source's descriptive examples are not proof of actual values in the vehicle or a substitute for the correct service procedure.c_t_tps_ad_dlyis a waiting period for a delayed request after ignition on, whereasc_t_tps_ad_pwlis a waiting period after entering the power-latch phase; both are in seconds. A requested or delayed operation is not proof the procedure ran successfully.
The THRO adaptation diagnosis reference lists c_crlc_tps_ad as a correlation constant used in determining adaptation values and c_tps_sp_spr_chk_up as a setpoint associated with a return-spring check. These relate to adaptation and checking, not maximum engine output or pedal sensitivity. Source captions and adjacent excerpts can conflict; verify the actual state machine, sensor scaling and implementation. Diagnostic conditions should not be changed merely to force a failed learn to pass.
Runtime signals and interpretation
v_tps_1_basandv_tps_2are throttle-sensor channel voltage measurements;v_tps_ad_el_bol_1andv_tps_ad_el_bol_2are lower-stop adaptation values for the channels. Check channel polarity, conversion, selected ECU and actual sensor wiring; neither channel's numerical range proves the plate is moving correctly. THRO aggregate-adaptation reference.tps_sp_adis a requested plate setpoint during adaptation;state_tps_bol_adis the state of continuous lower-stop adaptation. A state value needs the correct software enumeration and is not automatically a completed scan-tool basic setting. THRO diagnosis reference.tps_ad_cdn_missis described as information about a condition blocking throttle adaptation, andlv_tps_ad_act_enaenables the delayed adaptation path in the cited extraction. Check the enumerations and any fault-reaction inhibition; an enable flag alone is not confirmation of a successful result. Sources: aggregate fields and application fields.
Workshop diagnosis
- Record the full engine/other relevant fault codes and freeze frame, ECU software, original throttle part number, recent work, battery condition and whether the symptom occurs cold, warm, at idle or on load. A clean fault scan does not by itself verify the sensors or rule out mechanical issues.
- Use the manufacturer’s procedure to check the throttle body, connectors, supply/ground and signal plausibility, alongside air leaks and relevant pressure or fuel faults. Perform adaptation only if the current vehicle-specific procedure requires it; keep hands clear of the electrically moving plate and meet the tool’s stated conditions.
- Where available, compare pedal position, final throttle setpoint, both position signals, supply voltage and adaptation state with synchronised timestamps. Inspect requested and actual air charge, manifold and upstream-throttle pressures, engine speed, trims and relevant intervention states. A position error during a transition can also reflect sampling delay, scaling or active limits; a repeated mismatch deserves further testing.
- Record whether basic settings completed, aborted or were unavailable, and investigate any specific blockers and mechanical/electrical faults. Follow the specified post-repair checks. A successful position learn does not by itself prove leak-free intake plumbing, correct fuel delivery or acceptable drivability.
Volkswagen's 2014–2015 CXCA/CXCB scan-tool DTC table lists a throttle actuator performance path and separately lists intake-air correlation checks that include leaks. It is scoped to the documented engine and model years; a fault code or a table threshold from that document is not a universal Simos 18 diagnosis.
Worked example: warm-start stalling
An owner report (2019 GTI) describes warm-start stalling after fitting an aftermarket power module, a temporary improvement after removing it, recurrence after a dealer throttle adaptation, and a later statement that an ECU software update appeared to help the next owner. Exact ECU IDs, fault evidence and the causal chain were not independently verified. The changing report shows why a brief improvement after adaptation is not a conclusive diagnosis.
Related: throttle control · air charge modelling · idle control · torque model · wastegate actuator adaptation. References reviewed 17 November 2026.