
The M9T is the 2.3-litre common-rail diesel of the Renault–Nissan M family, designed for light commercial vehicles and first used in the Renault Master. It is also known as the Nissan YS23 and the Mercedes-Benz OM699. This guide covers identifying the engine and controller, health checks before calibration, the calibration areas involved and how to validate the result. It does not give map addresses or values, which depend on the exact ECU software.
Engine identification
The M9T displaces 2,299 cc with an 85 mm bore and 101.3 mm stroke and a 15.4:1 compression ratio. It is a double-overhead-camshaft engine with an aluminium block and head and common-rail direct injection, in production since 2010. Nissan MR engine, Wikipedia. The source is tagged as needing more citations.
- Output range: 102 to 190 PS and 285 to 450 N·m across all versions. At launch in the Master, outputs ran from 75 kW to 110 kW.
- Turbocharging: lower outputs use a single fixed-geometry turbo; higher outputs use a single variable-geometry turbo or twin turbos. The top Navara version is twin-turbo at 190 PS.
- Vehicles: Renault Master and Alaskan, Opel and Vauxhall Movano, Nissan NV400, Navara and Terra, Mercedes-Benz X-Class and Dongfeng Z9.
Establish the turbocharger arrangement first. A single-turbo and a twin-turbo M9T share a family name but not their boost control. Read the engine code from the plate and record the rated output.
ECU identification
Tool listings show four controllers on the 2.3 dCi, from two suppliers:
| Controller | Listed application | Source |
|---|---|---|
| Bosch EDC17C11 | Renault Master 2.3 dCi, 2012 | Abrites |
| Bosch EDC17C42 | Renault Master 2.3 dCi automatic, 2013 | Abrites |
| Continental SID309 | Renault Master 2.3 dCi; OBD read and write | AutoTuner, July 2017 |
| Continental SID310 | Renault Master 2.3 dCi 130 PS; Nissan Navara 2.3 dCi 160 PS | Alientech, July 2021 |
None of these listings gives the engine suffix or a complete build record, and the Master appears with all four. Read the ECU label, the supplier part number and the software identification before choosing a file, definition or tool protocol. A Bosch file does not transfer to a Continental controller, and an EDC17C42 or SID310 file from a 1.5 or 2.0 dCi does not transfer to the 2.3.
Health checks before tuning
- Injectors. Check injector condition and stored correction values before judging fuelling.
- Air, boost and aftertreatment. Check for boost leaks, turbocharger actuator faults and EGR problems. On twin-turbo engines, check both stages and their control. Where a particulate filter or AdBlue system is fitted, check its condition and history.
- Fault memory. Read and understand all stored faults first.
- Use and load. Most M9T applications are vans and pick-ups that run loaded or towing. Check the clutch, dual-mass flywheel, gearbox, four-wheel-drive components and cooling before increasing torque, and calibrate with that duty in mind.
Calibration areas
Both the Bosch EDC17 and Continental SID controllers are torque-based, but their map structures differ. See EDC17 torque fuel and tuning basics. The main areas are:
- Driver demand and torque limits, including gearbox and driveline protection.
- Torque-to-fuel conversion and smoke limits, which tie the injected quantity to measured air mass.
- Boost control, including targets, limits and actuator control; on twin-turbo engines, the switching between stages. Stay within each turbocharger's operating range, particularly under sustained load.
- Rail pressure and injection timing, which affect combustion pressure, noise and exhaust temperature.
- Protection strategies, which should remain active.
Work from a definition matched to the exact software identification; see Choosing ECU definition files.
Reading, writing and validation
Check the current documentation of the tool for the exact ECU and software, keep a verified copy of the original read, and support the battery voltage while programming. Renault's factory diagnostic application is described in Renault CLIP and Alliance Diagnostic Tool.
- Log requested and actual boost, air mass, injected quantity and rail pressure before and after the change, under the same conditions and, where possible, at representative load.
- Check for smoke, high exhaust and coolant temperature, clutch slip or gearbox faults and any new fault codes. Confirm that particulate-filter regeneration and differential-pressure readings remain normal.
Emissions and legal limits
Disabling or removing EGR, particulate-filter, AdBlue or other emissions equipment on a road vehicle can be unlawful and can fail inspection. Calibrate with all emissions equipment working. See Emissions cheating, defeat devices and enforcement cases.
Related pages
- Renault M9R 2.0 dCi tuning guide
- Renault G9U 2.5 dCi tuning guide
- Bosch EDC17C11
- Bosch EDC17C42
- Continental SID310
Sources
- Wikipedia, Nissan MR engine, M9T section: dimensions, outputs, turbocharging and vehicles. Accessed 19 November 2026. Secondary source tagged as needing more citations.
- Abrites, ECU compatibility list, Master 2.3 dCi entries. Accessed 19 November 2026; page numbers may shift. Tool coverage, not a build record.
- AutoTuner, Renault Master 2.3 dCi, Continental SID309, 19 July 2017. Accessed 19 November 2026.
- Alientech ECM Titanium driver update for Continental SID310 and SID307, 13 July 2021, as republished by a tool reseller. Accessed 19 November 2026.