Tuning Wiki

Sealed IP67 GPS logger with integrated storage for installations where a sealed enclosure is required.

Race Technology DL1 WP
Manufacturer comparison: the larger sealed WP is shown beside the PRO. Image: Race Technology, reproduced with permission; manufacturer source.

Specifications and capabilities

The manufacturer describes fixed internal 8 GB storage and USB download via the wiring harness. The WP and PRO share logging features but differ in physical construction, removable-card access and USB access. Manufacturer specifications and documentation.

Data analysis software

Use Device Explorer and the WP’s USB flying lead to retrieve files from its fixed internal storage, then review the recorded runs in Race Technology Analysis. Manufacturer documentation.

Race Technology Analysis showing graphs, lap times, video and a track map
Race Technology Analysis example; the available channels and video depend on the recording and enabled options. Image: Race Technology, reproduced with permission; manufacturer source.

Download Race Technology software for Windows. Check the current version and any licence or hardware requirements; some advanced functions require a unit-linked licence. See the Race Technology software overview for features and licensing.

Pinouts and cabling

Race Technology's shared PRO/WP documentation says it refers to both models as “DL1 PRO” in that section. Its connection page is titled PRO/WP, but the individual 19- and 24-way cable tables are headed PRO. The tables below reproduce those published cable assignments as a reference for the WP, based on that naming convention; a separate WP-specific connector table has not been located. Confirm the assignments and exact unit and loom with Race Technology before wiring. The original illustrates cable connectors; the face orientation of the WP mating connector has not been independently verified.

19-way cable: published PRO/WP reference

Cable contactPublished function
A / 1ADC1
B / 2ADC2
C / 3Sensor GND
D / 4System supply 12 V
E / 5Power GND
F / 6High-level RPM
G / 7RPM GND
H / 8GPS LED
I / 95 V reference 1
K / 10Frequency input 3
L / 11Frequency input 4
M / 12ADC4
N / 13ADC3
O / 14Power LED
P / 15Low-level RPM
R / 16Logging LED
S / 17Status LED
T / 18Frequency input 1
U / 19Frequency input 2

24-way cable: published PRO/WP reference

Cable contactPublished function
1ADC7
2ADC5
3ADC10 / output 2
4ADC9 / output 1
5ADC6
6ADC8
712 V for serial peripherals
85 V reference 2
9ADC12 / output 4
10ADC11 / output 3
11USB GND (PRO table; WP unconfirmed)
12USB 5 V (PRO table; WP unconfirmed)
13USB D− (PRO table; WP unconfirmed)
14CAN1 low
15RS232 port 1 GND
16RS232 port 2 GND
17RS232 port 2 receive
18RS232 port 1 transmit
19CAN2 low
20CAN1 high
21USB D+ (PRO table; WP unconfirmed)
22CAN2 high
23RS232 port 1 receive
24RS232 port 2 transmit

Contacts 11, 12, 13 and 21 are called USB ground, 5 V, D− and D+ in the PRO-labelled table, which explicitly says those USB cable contacts are not connected on the PRO. The WP uses USB on a flying lead. The source does not explicitly confirm the WP USB contact assignments or continuity, so do not treat the PRO “not connected” status or these labels as verified for the WP.

Sources: manufacturer shared-section naming convention; 19- and 24-way cable tables; WP differences.

RS232 [2] harness connector

Race Technology explicitly lists the following pin assignments for the DL1 Club, PRO and WP RS232 [2] harness connector in its ME221/ME442 interface instructions. These are pins on the RS232 harness connector, not the 19- or 24-way connector on the logger. Directions are from the logger's perspective.

RS232 [2] pinSignal
2RS232 receive (Rx)
3RS232 transmit (Tx)
5RS232 signal ground

For the documented ME221/ME442 connection, Race Technology specifies a serial extension lead between the ECU tuning port and the logger's RS232 [2] wiring-harness connector. For the ME221, its pinout lists ECU DB9 pin 2 as Tx, pin 3 as Rx and pin 5 as ground. Verify the connector markings, cable and ECU configuration before connecting; the other harness pins and the mating face orientation have not been verified here. Manufacturer ME221/ME442 connection and pinout.

Main connectors and USB

The WP has 19- and 24-way Binder main connectors at the front, a GPS connection at the rear, and USB on a flying lead. The published PRO/WP connection page identifies its detailed tables as DL1 PRO; it also marks the PRO's USB cable contacts as not connected. Do not assume those USB assignments describe the WP harness. Confirm the full numbered WP main-connector map with Race Technology for the exact unit and loom. WP construction and connections; connector specification.

Manufacturer connection reference.

Check the connector number, version and options on the actual unit against the manufacturer's documentation before wiring. Disconnect power before changing connections.

Wiring overview

Race Technology DL1 WP functional wiring overview
Functional wiring overview; not a connector-face diagram. Confirm actual connections with the manufacturer.

Return to the Race Technology manufacturer page.