Tuning Wiki

Mitsubishi's W6DGA Twin Clutch Sportronic Shift Transmission (TC-SST) is a six-speed automated gearbox with two wet clutch paths. Mitsubishi's TSB 16-22-003 identifies 2008–2015 Lancer Evolution, 2009–2015 Lancer Ralliart and 2009–2011 Lancer Sportback Ralliart TC-SST vehicles in its North American scope. Confirm vehicle, market, transmission, controller and software and consult the current service information; the bulletin was issued in 2016 and is not proof that the same repair policy applies today.

How the transmission works

Mitsubishi describes separate odd- and even-gear shafts with synchronised gears. Wet clutch packs connect the respective shafts, while hydraulic servos operate shift forks. Sensors monitor clutch speeds and fork positions; the transmission control module and valve body form the mechatronic assembly. This is a dual-clutch transmission, not a single-clutch automated manual or a torque-converter automatic. Mitsubishi TSB 16-22-003, operation overview.

Capture the complaint

The Mitsubishi diagnostic worksheet records mode, hot or cold conditions, affected upshifts or downshifts, noise, leaks and fault status. Save engine and transmission faults and freeze-frame data before clearing. Check battery and supply condition and use the correct diagnostic tool to compare requested and actual gear, relevant input speeds, temperature and clutch or shift state where supported. A harsh shift or speed discrepancy alone does not identify a failed mechatronic assembly or clutch pack.

For the covered 2016 bulletin procedure, Mitsubishi distinguishes a service-required message from an over-temperature warning and describes protective actions as temperature increases. Follow the actual vehicle's handbook for warnings and seek the appropriate service support; a temperature warning is evidence to investigate, not a universal temperature or a reason to ignore fluid loss. The bulletin also instructs technicians to check connectors and CAN communication as part of its diagnostic path. Mitsubishi TSB, diagnostic worksheet and pp. 7–8.

Examples of model-specific fault information

Mitsubishi's TSB 13-22-003 diagnostic manual describes P0715 and P0716 as different conditions affecting the first, odd-gear input-shaft speed-sensor system in its TC-SST diagnosis. It warns that network faults can produce misleading fault codes and directs CAN-bus checks before the illustrated diagnosis. The exact monitor, conditions and repair branch must be matched to the model year and controller; a speed code alone is not proof that a specific clutch or gear is defective.

Distinguish a shift request or actuator problem from sensor feedback, hydraulic control, power supply, engine torque delivery and gearbox mechanical issues using the appropriate vehicle-specific plan. Inspect leaks and cooling-system evidence where the current procedure directs. A symptom under only one mode or temperature narrows the test conditions, but does not by itself isolate a component.

Do not infer the failed part from limp mode

Mitsubishi's 2013 TC-SST service-manual revision for the listed 2008–2011 Lancer Evolution and 2009–2011 Lancer Ralliart applications shows different fail-safe responses. For example, P0776 and P0777 are grouped with faults that hold the current gear, while P0715 and P0716 appear in a group that may operate with one odd- or even-gear path. These are documented control strategies, not proof of a particular failed part or permission to continue driving. Save the original codes and observed gear behaviour, then follow the applicable diagnostic tree; the P0776 branch also requires CAN diagnosis. Mitsubishi TSB-13-22-003.

Shift-fork position codes

In the applications covered by Mitsubishi TSB-13-22-003, the fault index distinguishes shift-fork position sensor 1 voltage-low P1820, voltage-high P1821, output-range P1822, neutral P1823 and performance P1824 from the separate P1836 shift-fork 1 malfunction entry. Those labels describe different monitor results, not a diagnosis that the position sensor, fork magnet or mechatronics is necessarily defective. Capture the complete fault report, gearbox identity, request and available position data; follow the matching diagnostic branch, including the manufacturer’s CAN checks, before deciding on a repair.

The bulletin also lists position sensors 2–4 and their own distinct entries. Do not transfer these codes to another dual-clutch transmission or infer that all fork-related faults have the same physical cause. Mitsubishi’s 2013 diagnosis and parts policies are historical: verify the currently applicable service information and repair options for the individual vehicle.

Programming and service boundaries

The 2016 Mitsubishi bulletin describes a service case in which a new mechatronic assembly's controller requires programming and the prescribed teach-in. It treats the 2008 Evolution procedure differently from later cars and warns that some diagnostic functions move the vehicle or raise engine speed. Do not copy a software file, coding sequence, oil quantity or teach-in from a different year; use current Mitsubishi instructions, matching equipment and proper workshop precautions. A reset cannot repair a supply, cooling or mechanical fault.

See Fuso DUONIC commercial-vehicle dual clutch diagnosis for a different transmission, electronic gearbox guide, dual-clutch flywheels and automated clutch control.