Tuning Wiki
Browse MBE
Applies to

Check the hardware and software limits stated in this article.

Scope

The MBE 941 is a serial-interface standalone ECU from MBE Systems with a 55-way main connector. No complete public pinout has been located; the positions documented here come from two sources. MBE Systems' serial interface protocol description for the 941AA35x (manufacturer documentation) gives the serial port and mapping-trim positions on the main connector and on the 9-pin mapping connector inside the 941, whose numbering is also used by the MBE standard harness interface. SBD Motorsport's throttle-potentiometer guide for 941 and 970 ECUs (specialist documentation) gives the throttle sensor positions. All 55 main-connector positions and 9 mapping-connector positions are listed; those not covered by the sources are marked as not established.

Documented positions

On the main connector, position 45 is the ECU serial transmit, 46 the serial receive, 7 the ground for the serial and mapping connections, 47 the fuel trim input and 10 the ignition trim input. On the 9-pin mapping connector the same signals are on pins 2 (transmit), 3 (receive), 1 (ground), 6 (fuel trim) and 7 (ignition trim); for a PC 9-way D connector, transmit, receive and ground go to pins 2, 3 and 5. The serial port is a 5 V interface. Holding the fuel and ignition trim inputs above zero volts, as a 914 mapping box or an MBE comms lead does, selects byte mode for Easimap; with both trims at zero or open and logging enabled, the ECU broadcasts up to 16 parameters at 19200 baud. SBD gives position 30 as the 5 V throttle reference, 12 as the electronic ground and sensor return and 35 as the throttle signal; these are graded as suspected.

The sources list positions without face drawings, so both connectors are drawn as pin indexes. Assignments should be verified against the unit, its part number and harness before connecting power.

MBE 941 55-way main connector and 9-pin mapping connector pin index
MBE 941 main and mapping connectors as pin indexes; shaded positions are documented. Diagram redrawn by Tuning Wiki from MBE Systems and SBD Motorsport documentation.

Sources

Connector pinout

Applicability

MBE 941 (941AA35x) standalone ECU. Serial-port and mapping-trim positions on the 55-way main connector and the 9-pin mapping connector (inside the 941; the same numbering is used by the MBE standard harness interface) are from MBE Systems' serial interface protocol description (manufacturer documentation, dated 10 June 2015). Throttle sensor positions 12, 30 and 35 are from SBD Motorsport's throttle-pot guide for 941/970 ECUs (specialist documentation, graded suspected). All other positions are not documented in these sources. Both connectors are drawn as pin indexes; the face layouts are not given.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

55-way main ECU connector

Redrawn connector face
View: Pin index only; face layout not shown in the sources
55-way main ECU connector — Redrawn connector face. Pin index only; face layout not shown in the sources

Select a pin in a photograph or the index to highlight it.

55-way main ECU connector — complete pin index
PinFunction / cavityConfidence / sourceNotes
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Ground (serial and mapping)
Cavity: Populated
Confirmed

MBE serial interface protocol description

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Ignition trim input
Cavity: Populated
Confirmed

MBE serial interface protocol description

Held above zero volts by a 914 mapping box or MBE comms lead to select byte mode.
Unknown function
Cavity: Unknown
Unknown
Electronic ground / throttle sensor return
Cavity: Populated
Suspected

SBD throttle-pot wiring guide

SBD throttle-pot guide for 941/970.
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Throttle reference (5 V out)
Cavity: Populated
Suspected

SBD throttle-pot wiring guide

SBD throttle-pot guide for 941/970.
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Throttle signal
Cavity: Populated
Suspected

SBD throttle-pot wiring guide

SBD throttle-pot guide for 941/970.
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Serial transmit (ECU TXD)
Cavity: Populated
Confirmed

MBE serial interface protocol description

5 V serial interface.
Serial receive (ECU RCV)
Cavity: Populated
Confirmed

MBE serial interface protocol description

5 V serial interface.
Fuel trim input
Cavity: Populated
Confirmed

MBE serial interface protocol description

Held above zero volts by a 914 mapping box or MBE comms lead to select byte mode.
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown

9-pin mapping connector (inside 941) / MBE standard harness interface

Redrawn connector face
View: Pin index only; face layout not shown in the source
9-pin mapping connector (inside 941) / MBE standard harness interface — Redrawn connector face. Pin index only; face layout not shown in the source

Select a pin in a photograph or the index to highlight it.

9-pin mapping connector (inside 941) / MBE standard harness interface — complete pin index
PinFunction / cavityConfidence / sourceNotes
Ground
Cavity: Populated
Confirmed

MBE serial interface protocol description

PC DB9 pin 5.
Serial transmit (ECU TXD)
Cavity: Populated
Confirmed

MBE serial interface protocol description

PC DB9 pin 2.
Serial receive (ECU RCV)
Cavity: Populated
Confirmed

MBE serial interface protocol description

PC DB9 pin 3.
Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown
Fuel trim input
Cavity: Populated
Confirmed

MBE serial interface protocol description

Ignition trim input
Cavity: Populated
Confirmed

MBE serial interface protocol description

Unknown function
Cavity: Unknown
Unknown
Unknown function
Cavity: Unknown
Unknown