Tuning Wiki
Browse MBE
Applies to

Check the hardware and software limits stated in this article.

Connectors covered

The MBE 912 is an early MBE Systems engine-management controller. Its main connector assignments are documented for the 912-C version in a pinout sheet from SBD Motorsport, an MBE specialist and distributor, dated January 2014; a separate SBD wiring instruction for the 912 to 956 series describes a four-way Sure Seal harness interface. This article lists the 15 main-connector positions and the four interface positions. Both are specialist rather than manufacturer documents, so the assignments are graded as suspected, and the 912-C table may not apply to other 912 versions.

912-C main connector

Position 1 is the electronics ground, which also serves as the return for the throttle potentiometer and the coolant and air temperature sensors; positions 4 and 9 are braided power grounds, and position 2 is the ECU +12 V supply. Ignition drives are on 3 and 10 and the injector drive on 11. The crank (speed) sensor connects to 6 (signal) and 12 (return); with a GM sensor its screen goes to 4. Position 5 supplies the 5 V throttle reference and 15 receives the throttle signal; 7 and 8 are the air and coolant temperature signals; 13 is the tacho output and 14 drives the fuel pump relay or a gearshift light. The sheet lists the positions without a face drawing, so the diagram gives them as a pin index.

Harness interface

The four-way Sure Seal interface carries permanent +12 V on pins 1 (purple) and 2 (white), both fed from a relay whose contact is wired directly to the battery positive post with 2.5 mm cable; pin 3 (grey) is the earth trigger for a gearshift light and pin 4 (green) the rev counter signal. The wiring instruction draws the interface face but does not state the viewing side.

MBE 912-C main connector pin index and four-way harness interface
MBE 912-C main connector (pin index) and the 912/956 four-way harness interface. Diagram redrawn by Tuning Wiki from SBD Motorsport documentation.

Sources

Connector pinout

Applicability

MBE 912 standalone ECU: main connector of the 912-C as listed in the SBD Motorsport MBE912 pinout sheet (January 2014), and the four-way Sure Seal harness interface from SBD's 912-956 series wiring instructions (January 2014). Specialist distributor documentation, graded suspected. The 912-C table may not apply to other 912 versions; the main connector face layout is not given, so it is drawn as a pin index. The interface viewing side is not stated.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

912-C main ECU connector (15 positions)

Redrawn connector face
View: Pin index only; face layout not shown in the source
912-C main ECU connector (15 positions) — Redrawn connector face. Pin index only; face layout not shown in the source

Select a pin in a photograph or the index to highlight it.

912-C main ECU connector (15 positions) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Electronics ground
Cavity: Populated
Suspected

SBD MBE 912 documentation

Also the throttle potentiometer, coolant and air temperature sensor return.
ECU supply +12 V
Cavity: Populated
Suspected

SBD MBE 912 documentation

Ignition drive 1
Cavity: Populated
Suspected

SBD MBE 912 documentation

Power ground 2 (braid)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Also crank sensor screen for a GM sensor.
Throttle reference (5 V out)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Speed signal (crank sensor signal)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Air temperature signal
Cavity: Populated
Suspected

SBD MBE 912 documentation

Coolant temperature signal
Cavity: Populated
Suspected

SBD MBE 912 documentation

Power ground 1 (braid)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Ignition drive 2
Cavity: Populated
Suspected

SBD MBE 912 documentation

Injector drive
Cavity: Populated
Suspected

SBD MBE 912 documentation

Speed return (crank sensor return)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Tacho signal
Cavity: Populated
Suspected

SBD MBE 912 documentation

Fuel pump relay or gearshift light
Cavity: Populated
Suspected

SBD MBE 912 documentation

Throttle signal
Cavity: Populated
Suspected

SBD MBE 912 documentation

912/956 four-way Sure Seal harness interface

Redrawn connector face
View: As drawn in the wiring instructions; viewing side not stated
912/956 four-way Sure Seal harness interface — Redrawn connector face. As drawn in the wiring instructions; viewing side not stated

Select a pin in a photograph or the index to highlight it.

912/956 four-way Sure Seal harness interface — complete pin index
PinFunction / cavityConfidence / sourceNotes
Permanent +12 V via relay (purple)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Relay 87 output; relay 30 wired directly to battery positive with 2.5 mm wire.
Permanent +12 V via relay (white)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Paired with pin 1 from the same relay.
Gearshift light earth trigger (grey)
Cavity: Populated
Suspected

SBD MBE 912 documentation

Tachometer (rev counter) signal (green)
Cavity: Populated
Suspected

SBD MBE 912 documentation