Tuning Wiki
Browse MaxxECU Nissan
Applies to

Check the hardware and software limits stated in this article.

Connectors covered

The MaxxECU GEN1 plug-in adapter for the Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) fits MaxxECU STREET, RACE and PRO units. Besides the factory-loom plug, the adapter carries a 16-pin extra connector and a 3-pin connector for analogue input 4; the wideband lambda sensor is wired through a pre-wired 6-pin connector for a Bosch LSU 4.2 sensor. This article covers 25 pins: 16 on the extra connector, 6 on the sensor connector and 3 on the analogue input connector. The factory ECU connector is not covered.

16-pin extra connector

The manufacturer's guide draws the 16-pin connector from the wire side of the pre-wired harness, with pins 1 to 8 on the upper row and 9 to 16 on the lower row; the cavities also carry letters (H to A on the upper row, S to J on the lower). Pins 1, 2, 3, 4, 9 and 10 carry the wideband lambda signals. The other assignments are pin 5, GPO 7 / DIN 3 (output or digital input); pin 8, INJ 8 (output); pin 11, +12 V output; pin 12, +12 V output; pin 13, engine ground; pin 14, AIN 1 (temperature input); pin 15, AIN 2 (temperature input); pin 16, AIN 3 (0-5 V analogue input). Pins 5 and 8 are not available with the MaxxECU STREET. The guide lists no function for pins 6 and 7.

Wideband sensor and analogue input connectors

The 6-pin LSU 4.2 sensor connector, also seen from the wire side, carries VS on pin 1, RCAL on 2, heater +12 V on 3, heater H- on 4, VREF on 5 and IP on 6. The 3-pin connector has sensor ground on pin 1, analogue input 4 (0-5 V) on pin 2 and the +5 V sensor supply on pin 3; the guide does not draw its face, so the diagram gives it as a pin index only.

The guide is manufacturer documentation, last updated in 2017. Pin assignments should be checked against the adapter revision and the MaxxECU unit before wiring.

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in adapter extra connectors
Extra connectors of the MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) adapter. Diagram redrawn by Tuning Wiki from the MaxxECU installation guide.

Sources

Connector pinout

Applicability

MaxxECU GEN1 plug-in adapter for Nissan Skyline R32/33 GT-R/GTS-T (RB25/26), for MaxxECU STREET, RACE and PRO. Covers the adapter's 16-pin extra connector, the pre-wired 6-pin Bosch LSU 4.2 wideband sensor connector and the 3-pin analogue input 4 connector, from the manufacturer's installation guide (last updated 15 March 2017). The factory ECU connector pinout is not covered. Connectors viewed from the wire side; the 3-pin connector is a pin index only.

View orientation is stated beside each photograph. Unknown functions remain in the pin index.

16-pin extra connector (adapter)

Redrawn connector face
View: Wire side of the pre-wired adapter harness connector, as drawn by the manufacturer
16-pin extra connector (adapter) — Redrawn connector face. Wire side of the pre-wired adapter harness connector, as drawn by the manufacturer

Select a pin in a photograph or the index to highlight it.

16-pin extra connector (adapter) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Wideband lambda VREF
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Wideband lambda VS
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Wideband lambda shield
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Wideband lambda heater H-
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

GPO 7 / DIN 3 (output or digital input)
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Not available on MaxxECU STREET.
Unknown function
Cavity: Unknown
Unknown No function listed in the manufacturer table.
Unknown function
Cavity: Unknown
Unknown No function listed in the manufacturer table.
INJ 8 (output)
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Not available on MaxxECU STREET.
Wideband lambda IP
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Wideband lambda RCAL
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

+12 V output
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

+12 V output
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Engine ground
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

AIN 1 (temperature input)
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

AIN 2 (temperature input)
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

AIN 3 (0-5 V analogue input)
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Wideband sensor connector (Bosch LSU 4.2, 6-pin)

Redrawn connector face
View: Wire side of the pre-wired connector
Wideband sensor connector (Bosch LSU 4.2, 6-pin) — Redrawn connector face. Wire side of the pre-wired connector

Select a pin in a photograph or the index to highlight it.

Wideband sensor connector (Bosch LSU 4.2, 6-pin) — complete pin index
PinFunction / cavityConfidence / sourceNotes
VREF
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

IP
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Heater +12 V
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

Heater H-
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

VS
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

RCAL
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

3-pin extra connector (analogue input 4)

Redrawn connector face
View: Pin index only; face layout not shown in the source
3-pin extra connector (analogue input 4) — Redrawn connector face. Pin index only; face layout not shown in the source

Select a pin in a photograph or the index to highlight it.

3-pin extra connector (analogue input 4) — complete pin index
PinFunction / cavityConfidence / sourceNotes
Sensor ground
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

AIN 4 analogue input (0-5 V)
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)

+5 V sensor supply
Cavity: Populated
Confirmed

MaxxECU Nissan Skyline R32/33 GT-R/GTS-T (RB25/26) plug-in guide (manufacturer documentation)