This page summarises the service intervals, tightening torques and injection-control-unit tester checks in the factory Biturbo workshop manual, as reproduced on an enthusiast site (see References). They describe the 18-valve and 2.24v cars; confirm the exact model and market against the manual. Torques are given in both kgm and Nm as printed (1 kgm is about 9.8 Nm), with the manual's page number for tracing.
Maintenance schedule (manual page 0-57)
The chart lists a first service at 1,500 km (1,000 miles) and then services every 10,000 km (6,000 miles) up to 100,000 km (66,000 miles). The dot chart gives:
| Item | When |
|---|---|
| Engine oil and filter | At every service, including the first |
| Gearbox oil change | At 10,000, 40,000 and 80,000 km; level checked at most other services |
| Differential oil change | At 1,500 and 40,000 km; level checked at most other services |
| Valve clearance and ignition advance | Checked at every service, including the first |
| Spark plugs | Replaced at the services from 10,000 km as marked on the chart |
| Fuel filter and air cleaner | Replaced at the services from 10,000 km as marked on the chart |
| Idle speed adjustment | At 1,500 km and every other service thereafter (20,000, 40,000, 60,000, 80,000 and 100,000 km) |
| Timing belt replacement | At 40,000 km (about 24,000 miles) and 80,000 km; belt tension checked at the other services |
| Auxiliary drive belts | Checked at every service |
| Cooling system and antifreeze | Checked at every service |
| Brake and clutch fluid | Checked at every service; brake fluid replaced at least every two years |
The notes add that severe use (high speed on long trips, hot climates, short urban journeys in low temperatures) calls for engine oil changes every 5,000 km. The 40,000 km belt change matches the 24,000 mile figure given by specialists; the commonly quoted two-year or four-year age limit is not on this chart, so age should be treated as an additional limit.
Engine and driveline torques (manual pages 0-51 and 0-52)
| Fastener | Torque (kgm) | Torque (Nm) |
|---|---|---|
| Cylinder head nuts (16 off, 12 × 1.25) | 10 | 98 |
| Engine block coupling nuts (8 off) | 10 | 98 |
| Engine block Allen screws, inner and outer | 2.6–2.8 | 25.5–27.5 |
| Connecting rod cap screws (12 off, 10 × 1) | 6.5 | 63.7 |
| Flywheel to crankshaft (6 off, 12 × 1.25) | 10 | 98 |
| Toothed pulley to crankshaft | 8.5 | 83.4 |
| Toothed pulleys to camshafts (2 off) | 8.5 | 83.4 |
| Cam box cover Allen screws (16 off, 8 × 1.25) | 2.6 | 25.5 |
| Timing belt tensioner Allen screws (2 off) | 2.6 | 25.5 |
| Belt tensioner adjusting nut | 6 | 58.8 |
| Oil pump to block (Allen screws) | 2.6 | 25.5 |
| Intake manifold Allen screws (12 off) | 2.6 | 25.5 |
| Exhaust manifold special nuts (28 off) | 3 | 29.4 |
| Auxiliary pulley capscrews (4 off) | 3 | 29.4 |
| Starter motor (3 off) | 2.4 | 23.5 |
| Air-conditioning compressor screws / bracket | 5 / 7 | 49 / 68.7 |
| Alternator bolts (3 off) | 5 | 49 |
| Engine mount to rubber mount / to front frame | 8.6 / 6–6.5 | 84.3 / 58.8–63.7 |
| Clutch pressure plate to flywheel (6 off) | 3–3.5 | 29.4–34.3 |
| Wheel bolts (16 off wheel screws in the list, 12 × 1.5) | 8–8.5 | 74.8–83.3 |
The manual gives further chassis torques (differential, propeller shaft, suspension, steering) on page 0-52 that are not repeated here.
Injection control unit identification and tester checks (manual pages 1-34 to 1-38)
- The workshop tester pages name the injection control unit as a Weber IAW 04C and describe two test routes: a Unitest TMF 5000 with a dedicated injection card, and a Magneti Marelli Multitest. The tester plugs into the cigarette lighter socket and a lead to the connector near the control unit.
- The Unitest checks, shown with indicator lights, cover: tester power, wiring contact, starter signal, engine running or off, throttle extremes (full open or closed), manifold pressure below about 400 mmHg, air-conditioning on or off, top-dead-centre pick-up line fault, phase (cam) pick-up line fault, sequence error, air temperature sensor short or open circuit, water (coolant) temperature sensor short or open circuit, and manifold pressure sensor outside limits.
- Faults on the top-dead-centre or phase pick-up lines (short or open circuit) prevent starting, or shut the engine down if it is running; the manual shows the indicator-light pattern for each case in a second table.
- The injection control unit therefore uses these sensors: crank (TDC) pick-up, cam (phase) pick-up, air temperature, coolant temperature, manifold absolute pressure, throttle position.
Other practical items from the manual
- The main fuse box is behind the left glovebox, reached by prying the glove compartment loose; the relay fuse boxes are at the front right of the engine compartment; a 12 A / 15 V thermal switch for the front seat motors sits under the door-lock control unit in the glovebox.
- Headlights use four H4 60/50 W bulbs; the instrument and warning lights use 1.2 W wedge bulbs.
Not established
- ECU connector pin lists and part numbers.
- Service data for the later 24-valve 2.8 (222 4v, 430 4v) and the Shamal V8.
References
Related: factory service data, common faults and repair, Maserati Biturbo hub.