A compression tester measures pressure developed in a cylinder while an engine is cranked. A cylinder leak-down tester supplies regulated compressed air to a stationary cylinder and helps identify where air escapes. Both support mechanical diagnosis; neither result alone proves which component must be replaced. Use the vehicle manufacturer's procedure and specifications for the exact engine.
Compression testing
A conventional tester connects through a suitable spark-plug, glow-plug or injector adapter. Its check valve retains the peak pressure reached during cranking; a release valve resets the gauge for the next test. Digital testers can record results. Diesel engines often need higher-range equipment and engine-specific dummy glow-plug or injector adapters: a petrol kit's gauge, hose and fittings must not be assumed suitable.
The result depends on cranking speed, battery condition, engine temperature, throttle and valve operation, adapter and hose, number of compression strokes and the test procedure. Variable valve timing and engine design also matter. Record each cylinder, use the same prescribed conditions, and compare with the vehicle's specified limits and cylinder-to-cylinder variation rather than a universal pressure figure. OTC: digital compression tester.
Low readings can arise from valve sealing, rings, piston or cylinder damage, head gasket leakage, valve timing or test setup. A wet compression test is sometimes used to investigate ring sealing, but only when the vehicle manufacturer's procedure allows it: adding oil can affect the result and is not appropriate to assume for every petrol or diesel engine. Follow with further testing rather than treating the pattern as conclusive.
Cylinder leak-down testing
A leak-down tester uses a regulator and a calibrated restriction with gauge or percentage indication. With the engine stopped, the cylinder is positioned as prescribed, commonly at top dead centre on the compression stroke with both valves closed. Regulated air enters through a suitable adapter, and the technician reads the tester as instructed and listens for leakage. Setup and interpretation vary by tester; a percentage is not automatically comparable between devices with different restrictions or procedures. OTC 5609 instructions.
- Intake tract: air heard at the intake can suggest leakage past an intake valve or its seating.
- Exhaust: air at the exhaust outlet can suggest leakage past an exhaust valve or its seating.
- Crankcase: air at the oil filler or breather can indicate leakage past the rings, cylinder or piston; some leakage is normal and its significance depends on the engine and test.
- Cooling system or neighbouring cylinder: bubbles or air transfer can indicate a gasket, head or block sealing problem, but require confirmation. Do not open a hot or pressurised cooling system.
Repeat the test if positioning, adapter sealing or air supply is uncertain. Compare cylinders under consistent conditions and use the applicable manufacturer's limits. A leak-down test identifies a leakage path at the test condition; it does not by itself establish how the engine behaves under load. Sealey VSE2020 instructions.
Practical procedure and safety
- Identify the exact engine and obtain its test procedure, specifications and adapter. Inspect the tester, gauge, hose, seals and threads; a loose or leaking adapter can give misleading readings or be expelled.
- Secure the vehicle, select the required transmission position, ventilate the work area and follow the manufacturer's precautions for high voltage, moving components and fuel. Disable fuel and ignition only by the prescribed method. Engine temperature and throttle requirements are vehicle-specific.
- For compression, fit the correct adapter without cross-threading, crank as specified, record the peak and reset the gauge between cylinders. Restore the vehicle after testing.
- For leak-down, use clean regulated air, set up the tester as its instructions require and position the cylinder correctly. Applying air can rotate the engine. Keep clear of moving parts and use the manufacturer's approved method to hold or secure the engine; do not rely on the gearbox alone.
- Release pressure before disconnecting, account for all parts and verify the repair. Follow special procedures for glow plugs and injectors; incorrect removal or sealing can cause damage.
Diesel and direct-injection equipment can present fuel pressure and heat hazards. Do not loosen a high-pressure fuel line to disable injection. Use equipment and adapters rated for the expected cylinder pressure and do not exceed the lowest-rated component. Sealey diesel test kit instructions.
Complementary tests
A current clamp and oscilloscope can show relative compression by comparing starter-current variations between cylinders. This is a screening comparison, not a direct cylinder pressure measurement. A suitable pressure transducer can display a pressure waveform, while a borescope can show visible damage. Each has limits and needs its own rated equipment and procedure.
Tester and adapter directory
Part numbers identify the documented kits or accessories, not guaranteed vehicle fitment. Verify spark-plug thread, reach, seat, diesel adapter and gauge range for the exact engine. Kit contents and availability can change.
- OTC 5606 / 5605 — petrol compression: analogue 0–300 psi kits. OTC lists 10, 12, 14 and 18 mm options in the 5606; the deluxe 5605 adds a deep-well connector and a Ford 16 mm adapter. 5607 and 5608 are separately listed Ford 16 mm and 12 mm adapters. OTC engine-service catalogue.
- OTC 5605-DG — petrol compression: digital deluxe kit displaying multiple pressure units and recording readings for up to 12 cylinders. It includes standard and specialty adapters; consult the current kit list. OTC 5605-DG.
- OTC 5609 — leak-down: twin 0–100 psi gauges, regulator and 14 mm hose with 10, 12 and 18 mm thread adapters. The manufacturer's chart explains how to interpret its two gauge readings. OTC 5609; instructions and repair parts.
- OTC 5021 / 5020 — diesel compression: OTC identifies 5021 as a diesel compression gauge, up to 1,000 psi, with check and release valves; 5020 is listed as a diesel tester with adapters. Confirm the separate adapters required for the engine. OTC 5021; OTC catalogue search.
- Snap-on EEPV500 / EEPV509: EEPV500 is an automotive compression set; its parts list identifies EEPV5-300G gauge and boot and EEPV5G10S 10 mm adapter. EEPV509 is a leakage tester with an input gauge, percentage leakage gauge and 14 mm standard/long adapters; EEPV5G12L is a listed 12 mm accessory. EEPV500 parts; EEPV509 dealer listing.
- Sealey VSE2020 — petrol leak-down: two-gauge tester for the listed 10, 12 and 14 mm spark-plug applications; Sealey lists VS200/A or VS200/B long-reach adapters for some recessed plugs. Verify the revision and exact adapter. Sealey VSE2020.
- Sealey VSE204 / VS2044 — diesel compression: diesel kits with different glow-plug and dummy-injector adapter selections. The VS2044 instructions identify the VS2042/01 gauge/hose assembly, 0–1,000 psi, as the core of that range. Adapter inclusion and fitment differ between kits. VSE204; VS2044 instructions.
- Bosch FIX 7828 — compression: professional kit for petrol-engine compression diagnosis; Bosch notes that adapters must be secured to the hose to prevent separation on removal. Check its adapter list for the application. Bosch FIX 7828.
- Innova 3612 / 3614 — compression: respectively four- and six-piece kits in Innova's listing. The 3612 has a 0–300 psi gauge and release valve; the manual lists adapter and hose differences between kits. Innova 3612; 3612/3614 instructions.
- Motion Pro/K&L MTP08-0126 — four-stroke leak-down: a Harley-Davidson dealer equipment catalogue lists a regulator, gauge and 10, 12 and 14 mm hoses. Its listed replacement hoses are MTP08-0126X, Y and Z respectively. This is a historical catalogue entry; verify current availability. dealer equipment catalogue.
Older Snap-on equipment
MT308M is an earlier compression gauge set listed as discontinued and superseded by EEPV500 in an Acura dealer catalogue. Its documented M14 standard- and long-reach adapters are MT26J200R and MT26J300R. A 1999 Snap-on parts supplement separately documents the earlier MT308L set and its components. Check the exact model and replacement part rather than assuming every MT308 version is identical. MT308M dealer listing; MT308L parts supplement.
See also burnt valves and on-board and off-board diagnostics.