ADU5 Autosport is a five-inch dashboard/logger variant with a circular Autosport connector. ECUMASTER's ADU manual v120.2.4 shows ADU5 AS dimensions and lists IP65 for this version manufactured from 2025. The manufacturer’s ADU AS connector diagram lists 37 numbered positions; check the exact hardware and mating connector.

Data analysis software

Record the configured channels to the ADU's USB drive, then open the file in ECUMASTER Data Master to compare laps, graph channels and analyse logged data. Video synchronisation requires a suitable recording. Download Data Master and the manual; ADU USB logging instructions. Configure the ADU using its separate ADU software package. Available channels depend on the configured logger, sensors and ECU data.
See the ECUMASTER analysis software overview.
Specifications and logging
The ADU combines a configurable TFT dashboard, alarms and 15 RGB LEDs with acquisition of vehicle and sensor data. Its inputs include eight 0–5 V analogue channels, eight digital/frequency channels, two low-side outputs, a 0–5 V analogue output, CAN 2.0 A/B and RS232. GPS lap timing requires a suitable external GPS source. The manufacturer’s specification gives an operating range of 6–22 V and 3-axis accelerometer and gyroscope.
Channels can be logged to an external USB flash drive at up to 500 Hz, subject to channel and source rates. Configure channels, trigger and storage using the USB logging guide. Data Master analyses compatible recordings. An ECU's CAN message list and rate are separate limitations: confirm protocol, baud rate and channel availability.
Documentation discrepancy: ECUMASTER's product page states 800 × 480 pixels; its catalogue states 800 × 600. Verify the resolution for the exact product and revision with ECUMASTER.
Connector and pinout
ADU5 Autosport has the 37-position AS connector. ECUMASTER's ADU AS pinout identifies mating connector Deutsch AS614-35SN. Match the cavity numbers and drawing view to the actual component. The standard ADU5/ADU7 35-position pinout is different.
| Pin | Function |
|---|---|
| 1 | Battery 12V |
| 2 | Frequency/digital in D1 |
| 3 | Frequency/digital in D2 |
| 4 | +5V output |
| 5 | +5V output |
| 6 | AUX2 |
| 7 | Power ground |
| 8 | AUX1 |
| 9 | Analog in A2 |
| 10 | Analog in A1 |
| 11 | Analog in A3 |
| 12 | Analog in A5 |
| 13 | Analog in A7 |
| 14 | USB.VBUS |
| 15 | CAN1.H |
| 16 | CAN2.H |
| 17 | CAN2.L |
| 18 | Analog output |
| 19 | RS232.RXD |
| 20 | Frequency/digital in D3 |
| 21 | Frequency/digital in D4 |
| 22 | Frequency/digital in D5 |
| 23 | Frequency/digital in D7 |
| 24 | Analog in A4 |
| 25 | Analog in A6 |
| 26 | Analog in A8 |
| 27 | USB.DM |
| 28 | USB.DP |
| 29 | CAN1.L |
| 30 | RS232.TXD |
| 31 | Switched 12V |
| 32 | Frequency/digital in D6 |
| 33 | Frequency/digital in D8 |
| 34 | Sensor ground |
| 35 | USB.GND |
| 36 | Sensor ground |
| 37 | Ground |
Wiring and commissioning
Selected connections include battery supply 1, switched 12 V 31, power ground 7 and CAN1 high/low 15/29. USB uses VBUS 14, ground 35, data minus 27 and data plus 28. Follow the manufacturer's receptacle and connector views, power protection, ECU-specific CAN protocol and sensor requirements. The illustration is a functional schematic: grouped USB conductors are separate wires, and no connector-face geometry is implied. Configure and verify a short recording before use.
Manufacturer overview: ECUMASTER dataloggers and displays. Confirm revision, loom, connector and options before installation.