Tuning Wiki
Browse Dodge

This guide concerns the 2013–2016 Dodge Dart 2.0-litre petrol entry on HP Tuners' vehicle list, with a worked identification example for the 2014 North American model. The 1.4 MultiAir turbo and 2.4 MultiAir are different engine applications; do not assume that this 2.0 entry or its calibration definitions extend to them. Identify the exact vehicle, controller, calibration and transmission before buying a licence or editing a file. HP Tuners supported vehicle list; Dodge 2014 specifications.

Engine and transmission identification

Dodge's 2014 sheet describes the 2.0 Tigershark as a 1,995 cc naturally aspirated DOHC four-cylinder with variable valve timing and sequential multiport injection, rated at an estimated 160 bhp and 148 lb-ft. For that year the C635 six-speed manual was standard, and the electronically controlled 6F24 six-speed automatic was optional with the 2.0. The C635 dual dry clutch automatic in the same specification was optional with the 1.4 turbo; the C635 manual and C635 DDCT are not interchangeable descriptions. Dodge 2014 specification sheet; C635 dual-clutch diagnosis.

HP Tuners access and owner discussions

HP Tuners lists Dart 2.0 for 2013–2016. Its general Dodge service information says supported 2015-and-later petrol PCMs require an upgrade before tuning. Confirm the actual PCM, software, service availability, licence cost and interface compatibility with HP Tuners; a listed engine does not establish 6F24 TCM writing or any particular table or PID. Supported vehicles; HP Tuners locked-controller guidance.

In a Dart owner's discussion of a turbo conversion, a separate commenter said they had tuned their 2014 car with HP Tuners and discussed later-year PCM service. The conversion owner described an incomplete tuning arrangement. Neither an independently verified calibration nor a safe boost target was supplied, so the exchange is evidence of a question and an individual claim, not a recipe for a turbo conversion.

In a separate discussion of 2.0 and 2.4 tuning, the same commenter described tuning their own 2.0 using HP Tuners, while other participants discussed different tools and a proposed 2.4 tune. These are unverified individual reports, and a discussion of a 2.4 does not demonstrate HP Tuners support for that engine.

Practical logging and service checks

  • Start with a stable stock-file read, recorded PCM identification, fault codes and a baseline log. Check for intake or exhaust leaks, ignition and fuel-delivery faults before attributing fuel corrections or hesitation to calibration.
  • For warmed, steady and transient operating conditions, compare engine speed, throttle position, manifold absolute and barometric pressures, short- and long-term fuel trims, commanded mixture, oxygen feedback, spark and knock information where correctly defined and available. Compare matched conditions before and after a change; fuel trims alone do not establish wide-open-throttle mixture. Use an appropriately installed independent wideband for high-load mixture validation.
  • On a 6F24 car, note gear selection, vehicle speed and engine speed when a symptom occurs, and check transmission diagnostic data separately. Do not presume that an engine licence provides 6F24 shift calibration or all desired gearbox PIDs.
  • For a modified intake or forced-induction conversion, confirm sensor range and fuel system capacity and validate the actual vehicle on suitable equipment; no safe boost, ignition, or fuel value can be inferred from the forum posts.

Factory calibration context: FCA bulletin 18-067-16 covers 2014 Dart 2.0 vehicles with sales code ECK for specified diagnostic and system improvements. It supersedes 18-075-15, includes specific MIL codes and a generic Mode 6 display correction, and calls for factory wiTECH diagnosis and PCM reprogramming where the stated conditions apply. Check the exact vehicle and current service information first; the bulletin does not establish the cause of an unrelated symptom or an HP Tuners procedure. A factory update can replace a custom calibration, so document the vehicle's current software and tuning state before dealer programming.

Related wiki guides

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.