This guide brings together HP Tuners logging and owner experience for the supercharged 6.2-litre Dodge Challenger SRT Hellcat, using specific 2015 and 2016 examples. It is not a calibration file or a universal recipe: verify the vehicle, controller, sensors, software version and modifications before applying any observation.
Engine and gearbox identification
For the US 2016 Challenger SRT Hellcat, FCA specified a 6,166 cc supercharged, pushrod 16-valve V8 with sequential multiport injection, a 9.5:1 compression ratio and separate low-temperature cooling with dual water-to-air intercoolers. Published estimated factory output was 707 bhp and 650 lb-ft. The US specification lists the TR-6060 six-speed manual as standard and TorqueFlite 8HP90 eight-speed automatic as optional; the factory ratios for the automatic are 4.71, 3.14, 2.10, 1.67, 1.29, 1.00, 0.84 and 0.67:1. These are original US 2016 specifications, not proof of the gearbox or current output in a particular modified car. FCA, 2016 Challenger specifications, pp. 3–6.
HP Tuners access and starting point
Identify the PCM and calibration from the actual vehicle and establish whether the fitted transmission is automatic. HP Tuners' Stellantis page describes an upgraded PCM requirement for 2015+ FCA models with stated exceptions, and separate 2018+ Smart Access Cable requirements; its listed ZF8HP transmission controller coverage is distinct from PCM support. Exact access, supported controller, licensing and credits must be confirmed with the current vehicle and controller listing before work; do not infer PCM part number or TCM support from model name alone. HP Tuners Stellantis coverage and access; vehicle lookup.
Read and preserve the vehicle's own original calibration when supported, record controller identification, calibration, fuel, supercharger, pulley, injectors and sensor changes, and diagnose faults before calibration. In VCM Scanner, briefly connect to create a vehicle profile, then select the channels actually exposed by that profile. HP Tuners: scanning configuration.
Boost and MAP: identify what is being measured
A 2015 Challenger Hellcat owner with a 3.8 Whipple and replacement three-bar MAP sensors reported that VCM Scanner showed a MAP reading reaching 255 kPa before dropping, with an estimated boost reading different from the dashboard. This is a report from one modified vehicle, not proof of a universal 255 kPa limit, a faulty sensor or the cause of the disagreement. 2015 owner discussion: VCM Scanner and logging boost. Another owner of a modified 2016 Challenger compared reported MAP, a pressure-ratio calculation and a blower-lid gauge and raised a further discrepancy; the source does not establish a universal fix. 2016 owner discussion: HP Tuners MAP calculations.
Manifold absolute pressure and gauge boost use different references: gauge pressure equals manifold absolute pressure minus local atmospheric absolute pressure, with matching units. For illustration, 200 kPa absolute manifold pressure and 100 kPa barometric pressure correspond to 100 kPa, or about 14.5 psi, gauge. If—and only if—a pressure-ratio channel is defined as manifold absolute pressure divided by atmospheric absolute pressure, gauge pressure also equals (ratio − 1) × atmospheric pressure. Confirm the actual channel definition before using that equation; this example does not establish how a particular HP Tuners channel is calculated.
Compare synchronized RPM, MAP, barometric pressure and pressure ratio where available. Check sensor range and calibration, displayed units, measurement location, timestamps and sample rate, and compare against an appropriately ranged, independently verified gauge. A key-on, engine-off comparison with local barometric pressure can help check the reference, but it cannot validate full boost-range scaling. Do not select a tune target or alter sensor scaling solely to make two unverified displays agree.
Log changes before adjusting the 8HP90
For an identified automatic, record drive mode, requested and actual gear if available, vehicle speed, engine speed, pedal/throttle, commanded and measured lambda, ignition timing and available torque or shift-status channels. Separate engine and transmission changes so any effect can be attributed, and compare like-for-like operating conditions. Not every channel is available or reliable on every controller; limit the channel set enough to capture a shift. Check the wideband's calibration, exhaust location and transport delay before interpreting a brief mixture change during a shift.
Hellcat owners have discussed quicker shifts, fuel cut and torque-management changes, but their individual results and theories are not validated settings for other vehicles. Protect the driveline and engine: investigate the logged event and consult the relevant controller documentation before changing shift torque management or fuel controls. Community discussion: transmission tuning for quicker shifts; Community HP Tuners question and answer thread.
Related: Dodge Challenger generations and engines; Bosch ZF 8HP Gen1 mechatronic TCU identification; HP Tuners MPVI4.