Tuning Wiki
Browse Bosch

What this listing covers

Bosch designs the integrated circuits that sit around the microcontroller in an engine or transmission control unit. They make the regulated supplies, watch the processor, measure lambda and knock, and switch injectors, ignition stages, valves and relays. The processor itself is a separate chip. Families and examples are on the ECU microcontrollers page.

The rows below are Bosch's own description of each device, taken from the Spring 2011, Spring 2015 and Autumn 2016 Semiconductors and sensors catalogues and from the current Bosch Semiconductors product pages. A catalogue row is the intended job of that part. It does not say which ECU hardware number is fitted with it. Read the marking on the unit in front of you.

The letter prefix is not a function code. CC195 evaluates knock sensors, while CC770 is a CAN controller. CG124 supplies a transmission controller, while CG904 is an airbag system IC. Airbag, radar and parking parts are other control units and are left out of the tables. Alternator regulators such as the CR665 sit in the alternator; some speak LIN to the engine controller, and they are not ECU-board parts either.

A Bosch ECU board also carries chips from other makers. Those parts stay out of the catalogue tables. When a Bosch house number or a B-prefix marking is sold for one of them, the repair section records the shop's cross beside the industry datasheet.

System supplies

Bosch calls these system-basis and power-supply ICs. They feed the microcontroller and the sensors, and they add a watchdog, a reset, a main-relay driver and sometimes CAN or LIN. The Spring 2011 catalogue introduces the group as power for the CPU together with communication channels and the necessary inputs and outputs.

PartPurpose
CJ910Engine-management system-basis IC in a PSO36 package. 5 V system, standby and two sensor supplies, an ISO interface, a main-relay low-side driver, four signal low-sides, an ignition input and an RPM input. The 2011 and 2015 catalogues also list a flash-EPROM enable and a 28 µs RPM glitch filter.
CJ911The companion system-basis IC, also PSO36, with a switched-battery high-side and the same class of relay and signal drivers. The catalogues print a 12.5 µs RPM glitch filter and do not list the flash-EPROM enable that they print for the CJ910. A repair-shop identification of house number 30343 with this part is in the listings section.
CY310System-basis IC with 5 V and 3.3 V system rails, a 3.3 V standby rail and three 5 V sensor supplies. CAN, two ISO lines and SPI. Four low-side switches and one high-side. HIQUAD64. Spring 2011 and Spring 2015.
CY317System-basis IC adding a 2.6 V rail, ignition and wake inputs, a switched-battery high-side, a main-relay driver, four signal drivers, reverse-polarity protection and a digital watchdog. HIQUAD64. 2011 and 2015.
CY320System-basis IC for an engine or transmission controller. Rails at 5 V, 3.3 V, 2.6 V and 1.5 V, plus three sensor supplies programmable to 3.3 V or 5 V. CAN, an ISO line and SPI. Main-relay low-side, two pre-regulator modes, a three-level watchdog, and separate microcontroller and system resets. PSO36. Listed from 2011 through the current product page. Rutronik sells the CY320E under Bosch order code 1 267 379 284.
CY325System-basis IC marked new in Spring 2011. Rails at 5 V, 3.3 V, 2.6 V and 1.5 V, with 1.2 V optional, a 1 V standby rail and two 5 V sensor supplies. Buck, boost and linear pre-regulators. The catalogue describes the watchdog for Infineon TriCore and Freescale SNAKE microcontrollers. The 2015 and 2016 catalogues used here do not repeat this part number.
CY326System-basis IC in the 2015 and 2016 catalogues. Close to the CY325 description: optional 1.2 V or 1.3 V, a 1 V standby rail, two 5 V sensor supplies, CAN wake-up and a main-relay driver. The catalogues do not say that the CY326 replaced the CY325, so both rows stand.
CY324System-basis IC for an engine or transmission controller. 5 V, 3.3 V and a third rail of 5 V or 3.3 V, a switch-mode core from 1.125 V to 1.3 V, and three 5 V sensor supplies. SPI, CAN up to 2 Mbit/s and LIN. The current product page gives the core range; the Autumn 2016 catalogue also lists the part. Bare die, with other packages on demand.
CY327System-basis IC for an engine or transmission controller. 5 V, 3.3 V and a third rail of 5 V or 3.3 V, a switch-mode core from 0.9 V to 1.525 V, and three 5 V sensor supplies. CAN and LIN. A buck/boost pre-regulator is specified down to a 3 V battery. TQFP64 or TQFP100 with an exposed pad. 2015, 2016 and the current page.
CY329System-basis IC for an engine controller on the current product page. Two 5 V system rails, rated 550 mA and 950 mA, and three 5 V sensor supplies. MSC and a CAN FD physical layer. A main-relay low-side, seven further low-sides and one high-side. This part is not in the 2016 catalogue extract used here.
CY141Pre-regulator for a 24 V to 42 V board net, described as a main-relay substitute. It steps that input to 5.5 V–14 V and drives the gates of external main-relay switches. PSO36. 2011 through 2016.
CA510Combined 5 V microcontroller supply, rated 200 mA, and a CAN transceiver, with a 5 V I/O rail, a watchdog reset, current limit and undervoltage and overtemperature protection. QFN28. 2011 through 2016.
CA500Combined microcontroller supply and CAN transceiver. 5 V for the microcontroller and 5 V for analogue circuitry, three line inputs, three low-side line drivers and a reset output. The 2011 and 2015 tables give the package as PS020.

Wideband lambda interfaces

These chips run a wide-range oxygen sensor and return a lambda signal to the microcontroller. Which sensor matches which chip, and why two controllers can turn the same pump current into different voltages, is set out on the wideband oxygen sensor types page. The heater power transistor is external on the CJ125; the chip diagnoses that stage.

PartPurpose
CJ110Analogue interface for a Bosch LSU sensor. The 2011 and 2015 catalogues list lambda measurement in an SOIC16 package. The 2016 engine section no longer lists it.
CJ120SPI interface for a Bosch LSU, with lambda, probe-temperature measurement and diagnostics. Spring 2011 says new applications should use the CJ125. SOIC24. The 2015 engine section does not repeat it.
CJ125SPI control and amplifier for a Bosch wide-range LSU. Pump-current control, a lambda output amplifier, a Nernst reference, internal-resistance measurement for temperature control, programmable reference pump current, and diagnosis of the sensor lines and the external heater. The current product page names LSU 5.2, LSU 4.9, LSU ADV and LSU 4.2. Published in SOIC24 and LQFP32; those pinouts belong to different packages. Rutronik and Micros sell the LQFP32 part as 1 267 379 413. Micros also lists CJ125B as 0 272 230 522. AliExpress listings pair the SOP-24 part with house number 30481.
CJ135Later SPI interface. Bosch product information names the LSU 4.9 and LSU ADV, and the NTK ZFAS-U2, and states that the housing differs from the CJ125, so the two do not share a footprint. The current page adds LSU 5.2, ZFAS-U3 and Denso Plus 5 and Plus 6, and a regulation window from lambda 0.65 to free air. TQFP32 with an exposed pad.
CJ136The Autumn 2016 catalogue lists this with the CJ135 sensor set, LSU 4.9, LSU ADV and NTK ZFAS-U2, and adds a UART for cylinder-imbalance measurement. Same package family as the CJ135. Further product-information claims are on the wideband page.
CJ138Current wide-range interface with pin-pointing diagnosis. Pump-current control, results on SPI and UART, and detection of an open sensor pin or a short to ground or battery. The product page names LSU 5.2, NTK ZFAS-U3 and Denso Plus 6.1. TQFP32 with an exposed pad.

Injector drivers

The catalogues describe these as gasoline direct-injection power stages. They include the boost converter used for the high-voltage opening pulse, and they report faults over SPI.

PartPurpose
CJ840Four-cylinder GDI power stage. Two battery high-sides, two booster high-sides and four injector low-sides. One- or two-bank operation, parallel or double injection, current-level control and a selective valve disable. HIQUAD64. 2011, 2015 and 2016.
CJ841The same four-cylinder GDI arrangement. The catalogues' distinction is a higher current capability than the CJ840.
CY335Six-channel GDI driver for external power stages and shunts, with battery and booster high-sides on the chip. Current levels and boost voltage are set over SPI. TQFP64. 2015 and 2016.

Low-side switches

Port-fuel injectors, purge and boost valves, relays and heater loads are usually low-side switches: the ECU grounds the load. Channel counts below are the catalogue totals. A 14-channel part is not reserved for 14 injectors; the current ratings are mixed so that valves, relays and injectors can share one chip.

PartPurpose
CJ406Four low-side switches, each 2.2 A with a 70 V clamp, and a serial diagnostics interface. MultiWatt15. Spring 2011.
CJ420Four low-side switches, each 2.2 A with a 70 V clamp, with overtemperature detection and serial diagnostics. PSO20. 2011 and 2015.
CJ450Four smaller low-side switches, each 0.6 A with a 46 V clamp, with open-circuit and overtemperature detection. PLCC28. Spring 2011.
CJ920Fourteen low-side switches: six 2.2 A channels clamped at 70 V, two 2.2 A and two 2.7 A channels at 45 V, and four 0.6 A channels at 40 V. Open-circuit and overtemperature detection. HIQUAD64. 2011 and 2015. Repair shops sell this silicon under house number 30344, and Codecard prints order code B140593 for that number.
CJ945Eighteen low-side switches, mixing 1.1 A, 2.2 A and 3 A channels at 45 V or 70 V clamps. SPI and a microsecond bus. Open-circuit and overtemperature detection. HIQUAD64. 2011, 2015 and 2016.
CJ950 and CJ950PEighteen low-side switches, including two 8 A channels. The 2011 CJ950 feature list includes two channels for lambda-probe heaters, open-load and short diagnosis, 5 V monitoring and a second shutdown path. PSO36. Spring 2015 lists a CJ950P with the same outline and different on-resistances, so the suffix is kept in the name. Autumn 2016 lists a CJ950 again.
CJ960Eight low-side switches: four 3.0 A and four 1.0 A, clamped at 55 V. Controlled by SPI or by the microsecond channel (MSC), with a separate shutdown path for the first four outputs. TQFP64. 2015, 2016 and the current page.
CJ970Multi-channel power switch for a powertrain controller, including combustion-engine and fuel-cell units. Ten MOSFET drivers can be tied as half-bridges, H-bridges or a B6 bridge, and fourteen further low-side switches are integrated. MSC. TQFP100. Current product page.

Ignition-stage drivers

The catalogues call these inverting drivers for external ignition stages, with monitoring of the ignition wiring and the coil. The power transistor that switches the coil primary is the external stage, typically in the coil. The CK110 is the six-channel member of that family; CK200 and CK260 are six-channel SPI parts, and CK240 is the four-channel SPI part.

PartPurpose
CK110Six-channel ignition-stage interface with short-circuit protection and serial diagnosis. The catalogue row does not list SPI. SOIC20. 2011 and 2015. A board trace below associates house number 30397 with this part. Codecard sells 30397 in an HSOP20 package for VW, Audi and Seat ECUs.
CK200Six-channel SPI ignition driver with wiring and coil diagnosis. Bare die. 2011 and 2015.
CK240Four-channel SPI ignition driver with short-circuit and wiring diagnosis. Bare die or SOIC16. 2011, 2015, 2016 and the current page.
CK260Six-channel SPI ignition driver with short-circuit and wiring diagnosis. SOIC20. 2011, 2015 and 2016.

Knock, speed and analogue inputs

Knock chips filter the piezoelectric knock-sensor signal and pass a result to the microcontroller. The CY30 is the crank or cam interface in the same catalogue section. The CY100 is a separate analogue-to-digital converter for voltages the processor does not read itself.

PartPurpose
CY30Single-channel rotation-speed interface. Differential input, selectable thresholds and an open-drain output. SOIC8. 2011 through 2016.
CY100Eight-channel, 10-bit analogue-to-digital converter. 5 V conversion range, about 120 µs, ISO SPI, plus two open-drain digital outputs. LQFP32. 2011 through 2016.
CC195Knock evaluation with an analogue output. Two symmetric inputs or four asymmetric inputs. Programmable gain and a switched-capacitor band-pass. PLCC28. 2011 through 2016.
CC196Knock evaluation with an SPI result. Programmable gain and a digital FIR band-pass. SOIC16. 2011 through 2016.
CC650Knock evaluation combined with a 16-channel, 8-bit analogue-to-digital converter, a reset module and a post-run module. Digital I/O. MQFP80. Spring 2011, where it is the only device listed in that package. The 2015 and 2016 knock tables do not repeat it.

Throttle and motor bridges

The Autumn 2016 catalogue heads this group as smart bridges for throttle-valve drives, pumps and other motor-driven actuators.

PartPurpose
CJ220Full H-bridge, about 150 mΩ and 6.6 A, switching to 30 kHz. Integrated free-wheel diodes, current limit, undervoltage lockout, overtemperature protection, short-circuit shutdown and diagnosis. PSO20 in 2011 and 2015; the 2016 table says Power SO-20. Codecard sells house number 30348 as this class of motor driver and describes it as a substitute for the Motorola MC33186.
CJ260Monolithic B6 bridge for a brushless motor up to 60 W. SPI and direct inputs, 3 A RMS, 20 kHz, with current limit and diagnosis. Power SSO-36. Autumn 2016 and the current page.
CY146Gate pre-driver for six external high-side or low-side MOSFETs. The 2016 catalogue allows a B6 bridge, an H-bridge, three half-bridges or other arrangements, with an integrated PWM generator and SPI. LQFP44. Also listed under engine management in 2011 and under electric drives in 2015.

Transmission control

Transmission parts supply the controller, watch it, and regulate the current in hydraulic valves. The 2016 catalogue describes the CG124 and CG130 pair as the supply, the starter-disable path and the monitoring, split across two chips so that a fault in one does not remove the other.

PartPurpose
CG124Transmission system-basis IC. Microcontroller supplies, speed and position inputs, high-side switch drivers and a starter-disable switch. SPI and ISO/LIN. The catalogues say the pair suits a Renesas SH7. TQFP64. 2011, 2015, 2016 and the current page, which presents it with the CG130.
CG130Monitoring companion to the CG124. Question-and-answer watchdog, microcontroller-core voltage monitoring, peripheral clock monitoring and a reset. LQFP32.
CG135A later monitoring IC for a transmission controller. It watches supply voltages, high-side switches and the microcontroller, and it can reset the processor or disable the high-side switches. SPI. The current page describes it for ASIL D systems. It is a different part from the CG130.
CG202Single-channel current regulator for an inductive transmission valve. The power switch, shunt and free-wheel diode are external. Range about 0 to 1,200 mA with a 1 Ω shunt. SOIC16. 2011 through 2016.
CG207Two-channel current regulator with the switches, shunts and diodes integrated, for low-side valves. Range 0 to 1,023 mA, accuracy stated below 2.5%. SPI. Bare die or PSO36. Spring 2011.
CG208Two-channel integrated current regulator, 0 to 1,200 mA, accuracy stated below 1%, with dither and overcurrent and overtemperature protection. SPI. Bare die or TQFP44. 2011, 2015, 2016 and the current page, which titles it as a two-channel magnetic-valve current regulator for an automatic transmission.
CG211Four-channel shunt measurement for low-side, high-side or bridge currents, with bit-stream outputs and diagnosis. LQFP32. Spring 2011.
CG240Six-channel integrated current regulator for low-side inductive loads. 1.2 A channels that can be paralleled, current-control or switch mode on each channel, and dither. SPI. Bare die or TQFP100. 2015 and 2016.

CAN controllers and transceivers

Later system-basis ICs include a CAN physical layer, so a separate transceiver is not always present. Where the microcontroller has no CAN controller of its own, Bosch offered a stand-alone controller as well. The catalogue protocol for the CC750 and CC770 is CAN 2.0 A and B. The transceivers are ISO 11898 physical layers.

PartPurpose
CF150CAN transceiver with a 5 V microcontroller interface. The Spring 2015 catalogue says new applications should use the CF151.
CF151CAN transceiver with high-speed and low-speed modes and slew-rate control. SOIC8. Spring 2015.
CF160CAN transceiver for up to 1 Mbaud, 5 V microcontroller interface, slew rate set for that rate. SOIC8. 2015 and 2016.
CF163The 3.3 V-interface counterpart of the CF160. SOIC8. 2015 and 2016.
CF1733.3 V CAN transceiver with standby and wake-up. The catalogue also marks it for truck use. SOIC8. 2015 and 2016.
CF1755 V CAN transceiver with standby and wake-up, also marked for truck use. SOIC8. 2015 and 2016.
CC750Stand-alone CAN 2.0 controller on SPI. Fifteen message objects of eight data bytes and a programmable bit rate. SOIC16. 2011, 2015 and 2016.
CC770Stand-alone CAN 2.0 controller with SPI, a parallel CPU bus and two 8-bit I/O ports. Same message memory as the CC750, plus a programmable clock output. LQFP44 or PLCC44. 2011, 2015 and 2016.

Numbers printed on the package

The catalogues use names such as CJ920. Older ECU packages are often marked with a short house number such as 30344. Bosch's public catalogues do not print the cross-reference. Repair shops and AliExpress sell the chip under that short number. Markings and order codes that start with B are recorded in the next section.

One trace of a single Bosch ME7.5, from a 2001 Audi A4 1.8T with engine code AWM, was published on Nefarious Motorsports. The author matched package and supply pins against Bosch product sheets. The table is that comparison. It belongs to the board that was examined.

MarkingIdentification from that traceWhat the author found it doing
30397CK110Ignition-coil paths. Six-channel ignition-stage interface in the catalogue. Codecard sells the same number in HSOP20 for VW, Audi and Seat ECUs. Inovauto sells 30637 and 30490 beside it as SOP-20 ignition drivers. Those two numbers were not on the traced board, so the CK110 identification stays with 30397.
30348CJ220Drive-by-wire throttle motor. H-bridge in the catalogue. Codecard sells it as a motor and solenoid driver and as a substitute for the Motorola MC33186.
30381CJ420BVariable-cam solenoid and idle valve. The public catalogues list the CJ420 quad low-side family and do not print a CJ420B row. The author cited a CJ406/CJ420B product sheet. Auto-chips instead lists 30381 as an ME7.5 fuel-injection driver, which is a different job from the one this trace found.
30344CJ920Fuel injectors and the N75 valve. Fourteen-channel low-side switch in the catalogue. Codecard and Inovauto print order code B140593 for this number.
30345CJ110Wideband-sensor leads. Analogue LSU interface in the catalogue.
30380CC650Identified because the semiconductors brochure listed one MQFP80 device, the CC650: knock evaluation, a 16-channel converter, reset and post-run. The same trace also followed barometric and leak-detection connections to this package. Inovauto lists a 30380 in QFP-64 as a generic ECU driver. That is a different package, so it is not combined with this identification.
30343CJ911, in a later traceThe original ME7.5 trace left this PSO36 part unidentified and named the CJ910 and CJ911 as candidates. A rusEFI post identifies it as the CJ911 and, on ME7.5 hardware 8E0 909 557D, follows 5 V, standby, K-line and the main-relay driver to the package. Repair shops sell it as an HSSOP-36 voltage regulator.

A Bosch 30098 removed from a Motronic M1.7.3, Bosch number 0 261 203 661, is described by Silicon Prawn as knock-signal processing. That reading comes from the die and the board, and the catalogue name is not established here.

A later thread on the same forum guessed at MED9.1 markings from package shape and position. Those guesses are not listed.

Repair shops and AliExpress

AliExpress, Inovauto, Codecard, ECUdiag, EDF Componentes, Pontedeira and Auto-chips sell these chips as ECU repair parts. The title is usually the word Bosch followed by the short number on the package, such as 30344 or 30481. Two different B-prefix codes turned up. B140593 is the order code Codecard and Inovauto print for house number 30344. B58290 is a marking Codecard identifies as the Infineon TLE4226G, a part fitted to older Bosch boards rather than a Bosch ASIC. Distributor order codes checked at the same time do not use a B prefix. Rutronik's CJ125 is 1 267 379 413 and its CY320E is 1 267 379 284.

Where a shop says one number can substitute for another, that is the shop's repair claim. It is not a Bosch statement that the dice match. The same shops file ST L9651 and the Infineon TLE8209-1E, TLE4226G and TLE6244X under Bosch ECU chips because those parts are fitted to Bosch boards. A repair equivalence table circulated as Tabela Equivalencia groups short numbers by the job a workshop assigns them. It is cited here as a shop table, not as a Bosch cross-reference.

MarkingWhat the listing calls it
30344, order code B140593. Shops also name 30403, 30578, 30579, 30614, 30621 and 48007Injector and valve driver in QFP-64 or HQFP-64. AliExpress titles 30344 and 30614 as fuel-injection drivers. Inovauto names ME7 and EDC15 boards, including ME7.4.4 and ME7.5.20, and also an EDC16 Nissan case. The ME7.5 trace identifies 30344 as the CJ920. The repair table agrees on 30344, 30403 and 30614 as injector, fan and pump drivers for ME7.4.4 and ME7.5.20. The same table instead calls 30578 and 30621 a 5 V regulator and lambda-probe circuit, QFP-64, on ME7.5.30. That job conflicts with the injector-driver substitute list, so those two numbers are not treated as a CJ920.
30343. Shops also name 30402, 30430, 30595, 30604, 30606 and 30639Voltage regulator in HSSOP-36. ECUdiag, Epic and EDF use that description, and the repair table calls the group a 5 V regulator on ME7.4.4 and ME7.9.6. AliExpress calls 30343 and 30430 the supply chip for ME7.5 boards, including an M7.9.7 Golf listing. Codecard lists 30639 as the power supply in an ME7.9.7 ECU. Inovauto titles the same HSSOP-36 group as a relay driver for EDC15C2, and names ME7.4.4, ME7.9.6 and Sprinter. The rusEFI trace identifies 30343 as the CJ911, whose catalogue package is PSO36. That identification is for the traced 30343, not for every number in the shop list. A CJ911 does carry both 5 V supplies and a main-relay driver, which is why a regulator title and a relay title can describe one chip without making the substitute numbers the same silicon.
30481AliExpress and Alitools sell it as CJ125 in SOP-24, a wideband oxygen driver. Inovauto lists the same number as an SOP-24 ECU driver. The catalogue CJ125 was published in SOIC24 and, later, LQFP32. The SOP-24 listing matches the earlier package.
30536, with 30620 and 48017Auto-chips calls 30536 a fuel-injection driver. Inovauto, Epic and Pontedeira sell 30536, 30620 and 48017 as the Infineon TLE6244X, an 18-channel low-side switch in PQFP-64. Inovauto names EDC7, ME7.4.9, MG7.9.8 and EDC16 boards, and also names Mercedes ECU 0 281 912 435. The Infineon datasheet describes that switch. The Bosch numbers are the markings those shops print. No Bosch catalogue name is established for them.
30651Fuel-injection driver on DMEtronic and Auto-chips. No catalogue name or industry cross is established for this number here.
30554Power driver for Mercedes-Benz M272 and M273 ME9.7 boards, QFP-64, on AliExpress and DMEtronic. Codecard adds Mercedes ECU 0 281 912 435. The same hardware number is copied onto other Codecard and Inovauto driver listings, so it is this shop's example ECU, not proof that every grouped chip sits in that unit.
B58290Codecard sells the Infineon TLE4226G, which it calls an intelligent sixfold low-side switch, under Bosch marking B58290. The Infineon datasheet is a P-DSO-24 part with four 50 mA outputs and two 500 mA outputs. Its Infineon ordering code is Q67000-A9118, not B58290. EDF sells the TLE4216G and the TLE4226G together against B58290, in SOP-24, and says the marking is found on Bosch M1.5.4, M2.10.4, M3.8.3 and EDC15C2 boards, and on Digifant 1.74 and 1.82. The repair table calls B58290 the ignition-coil driver on M1.5.4 and Digifant. The datasheet describes the switch and does not name the coil. The TLE4216G is a different Infineon device, so the combined listing is a shop substitute.
30373, and 30127 on the same Inovauto listingZIP-15 injector driver for Niva, VAG and Nissan, on MP1.5.4, MP7.0 and MP7.1, at Codecard and Inovauto. Both say it may replace a TLE5216 and Bosch 30374. TVSAT sells 30373 in SIP-15 and prints it as a TLE5216. The Siemens TLE5216G is a 20-pin SOP quad low-side switch for valves and relays, so that cross is not a matching package.
30374Codecard: injector driver for BMW DME and Mercedes-Benz ECUs, sold as its own part. The listing does not give a package, and the suggested swap with 30373 is the shop's claim.
30306Codecard: injector-transistor supervisor in EDC15 and EDC16. The listing names Audi A3, Seat Altea and Leon, Skoda Octavia, and VW Caddy, Golf, Jetta, Transporter and Touran 1.9, 2.0 and 2.5 TDI from 2003 to 2007.
30637 and 30490Inovauto sells both with 30397 as SOP-20 ignition drivers for ME7.5, including ME7.5.10 and ME7.5.20. The repair table pairs 30637 with 30397 the same way, for ME7.5.10 and ME7.5.20. The CK110 identification remains the ME7.5 trace of 30397.
30407, 30532 and 30618Pontedeira and the repair table: QFP-64 multi-driver, grouped together, for EDC16. The table names EDC16C9. Pontedeira names an S10 diesel ECU. 12volt-shop lists 30407 as an EDC16 chip in QFP-64. The load on each channel is not named.
30458, 30460 and 30616The repair table groups these as a QFP-64 multi-driver for EDC16C9. 12volt-shop lists 30460 on its own as the driver for EDC16 U1. The channel loads are not named, and the two ECU names are the shops' applications.
30427Pontedeira: SOP-24 ignition driver for Mercedes-Benz ME9.7. One listing. A MED9.1 discussion left this marking unidentified, so the shop title is not a board trace.
40049Codecard calls it an EDC17 power-supply IC. ECU Fix Tool calls it an ME17 injection driver. AliExpress files the number in a mixed lot of drive chips. The descriptions are left side by side.
30057Codecard: Mercedes, VAG and BMW ECU transistor. The listing says clients reported that 30057 can replace 30021 and 30028. Pontedeira sells it in SOT-404. That is a customer report about a discrete transistor.
30591AliExpress calls it an EDC7 diesel power driver in HQFP-64. Inovauto offers 30591 as compatible with 30554, 30592, 40114 and 30622, which is that shop's substitute list. Pontedeira sells 30622 as the motor driver in a VW Golf diesel EDC16, hardware 0 281 222 111, and 12volt-shop sells 30622 as a QFP-64 EDC16 driver for Audi and VW. Those are separate shop applications for one number inside the substitute list.
30529Inovauto: power regulator, SOP-36.
30519AliExpress: HSSOP-36 chip for a Bosch diesel ECU. The listing does not name the load.
30023 and 30046Inovauto: ignition or injector MOSFET, 30046 in TO-220. These listings are discrete transistors, not the multi-channel driver ICs above.
30021Inovauto: voltage-regulator transistor in TO-263.

Inovauto's catalogue runs well past this table. Many further numbers, including 40005, 40055, 40076, 40111, 40176 and 40184, are titled only as an ECU driver, with a package and no load. Those titles are not repeated here until a listing or a board trace names the job. AliExpress describes 40138 as a QFP-100 ECU chip, while Inovauto describes 40138 as an airbag driver and pairs it with 48054, so that number is left without a single function.

Sources

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.