BMW's September 2005 SMG III training module documents the E60 M5 Getrag 247 seven-speed automated manual. It is a different design from the E46 M3 SMG II. This page is scoped to that documented M5 system; confirm the exact vehicle and current service information before diagnosing a different BMW. The module is in the supplied BMW training file 05_SMG III.pdf, PDF pp. 3–4, 9–14 and 23–25, and in the BMW SMG III training module hosted by PDFCoffee.
Construction and control
The documented Getrag 247 was designed for automated operation, with individual hydraulically moved selector rods and hydraulic gearshift equipment integrated with the gearbox casing. BMW describes a dual-mass flywheel and a two-disc dry clutch connecting the engine to one transmission path: a two-disc clutch is not the same as a dual-clutch transmission with two independently controlled gear paths. The controller coordinates gear selection, clutch position and engine intervention. BMW training, SMG III pp. 4 and 8–10.
Hall sensors monitor the working-piston positions for gear recognition; a Hall sensor measures gearbox input speed. The documented system uses the hydraulic-fluid temperature signal to estimate gearbox-oil temperature for gear-oil pump control. Brake, bonnet, door and engine-speed signals also affect operation. A related fault can therefore originate in electrical inputs or communications, not only the gear mechanism. BMW training, SMG III pp. 9 and 12–13.
Hydraulics and pressure
An electric pump charges an accumulator through a check valve. The unit includes a pressure sensor, pressure limiter, temperature sensor, clutch actuator and valves. For the documented E60 M5, BMW states a normal operating pressure of 75 bar and 90 bar during learn-in or initialisation. These are descriptions of this system, not universal acceptance limits for other SMG generations. Compare pressure and pump command using the current BMW diagnostic plan; do not treat a single reading or pump sound as a complete test. BMW training, SMG III pp. 9 and 14.
Pressure can remain in the accumulator after switching off. Use the manufacturer's safe service and pressure-release procedure and suitable equipment before opening the circuit. Distinguish the actuator hydraulic circuit from gearbox lubrication and use the exact current specification for the vehicle.
Symptoms and diagnostic direction
- Failure to select or move off: record requested and actual gear, brake status, bonnet and door status, clutch position, stored faults and pressure/actuator state. BMW's example requires both bonnet contacts closed for starting off; an indeterminate contact state can prevent gear engagement. Do not bypass an interlock. BMW training, SMG III pp. 12–13.
- Pump or pressure complaint: distinguish pressure feedback from pump command; check supply, relay/control, sensor plausibility, hydraulic leaks and pressure retention with the manufacturer test plan. BMW describes a diagnostic accumulator-preload function based on pressure and timing: it is a guided service function, not proof that a particular accumulator has failed based on pump cycling alone. BMW training, SMG III pp. 14 and 24.
- Harsh shift after repeated slipping: BMW describes a clutch-overload protection strategy based on calculated thermal load. Its first stage can reduce slip and feel harsh; continued overload can trigger further protection and a warning. Record conditions and temperatures and investigate real clutch and control faults too; harshness does not prove this strategy was active. BMW training, SMG III p. 23.
- Adaptation abort or gear-recognition fault: capture the exact test phase, fault and measured states. BMW's clutch learn-in example aborts if input-shaft speed is detected during the fast approach phase and cites an issue such as bleeding as a possible cause. A failed learn-in is not a diagnosis of a specific component. BMW training, SMG III pp. 24–25.
Documented hydraulic and gear-blocking cases
Hydraulic fault group: BMW SI B23 07 06, March 2010 describes E60 M5 and E63 M6 GS7S47BG examples with a transmission warning, failed selection and combinations of 4F42, 4F43 or 4F40; clutch-position deviation 4FA0 may also be present. BMW’s guided sequence distinguishes accumulator precharge, clutch and hydraulic-unit checks. It refers an isolated 4FA0 without the hydraulic faults to a different diagnosis. The codes do not individually establish that the pump or accumulator requires replacement; use the current vehicle-specific test plan.
E60 M5 pump-motor service action: BMW SI B23 01 07, August 2007 describes premature brush wear in the hydraulic-pump electric motor on affected E60 M5 S85 vehicles produced from 25 January 2005 through 23 January 2006. BMW describes loss of hydraulic pressure, a transmission warning and possible 4F42, 4F43 or 4F40 entries; gear selection may become unavailable. Its service action replaced the pump motor on affected vehicles. BMW says the production range alone is not decisive: check the individual vehicle and action status in the current BMW service system. These codes can have other causes and do not establish that an unverified car has the motor defect.
Pump motor versus complete hydraulic unit: BMW’s June 2013 service roundtable, SMG III section discusses the E60 M5/E63 M6 GS7S47BG low-pressure fault group and directs technicians to the SI B23 07 06 diagnostic procedure. When motor replacement is being considered, BMW highlights inspection of the motor output shaft, coupling and pump input shaft; rounded coupling wear or severe pump corrosion can affect whether the entire hydraulic unit is needed. This is a condition-based decision in BMW’s historical service material, not an instruction to replace either assembly from a code alone. Follow the current vehicle-specific diagnostic and repair instructions.
5101 hydraulic-sensor fault with emergency mode: BMW’s SI B61 14 03, September 2006, page 3 lists an E60 M5 case where fault 5101 (“analyze hydraulic sensor”) and emergency-mode operation were addressed by an SMG software correction; BMW refers to SI B23 01 06 for the specific issue. Confirm software level, complete fault context and current guided diagnostics before attributing a stored 5101 to software or replacing a pressure sensor. Real sensor, wiring and pressure faults remain possible; this historical bulletin does not justify a generic update or parts replacement.
Intermittently blocked gear: BMW SI B23 03 08, December 2008 describes E60 M5 and E63/E64 M6 SMG III vehicles in its production and software range where a requested gear flashes, a different gear is selected and a gear is unavailable until an ignition cycle. Its documented cause is an SMG software error with possible 4F82–4F85 gear-blocking codes. Check production date, integration level and current BMW instructions; the same symptoms can have other causes and the bulletin does not cover every SMG.
Service and adaptation
BMW describes distinct service functions for clutch grab point, shift-range midpoints, valve characteristics, transmission characteristics and longitudinal-acceleration sensor offset. Some repairs or programming require new adaptation; the applicable function, vehicle state and sequence depend on the work performed. These routines move components and require the correct diagnostic equipment and current workshop instructions. Record existing faults before clearing them; repair the underlying cause and verify the original symptom afterwards. BMW training, SMG III pp. 24–25.
BMW also documents a wheel-circumference teach-in for this example after changes in rolling circumference. Use the applicable owner's and service instructions and a safe authorised environment; do not infer its sequence applies to other transmissions. The supplied training document is a technical reference, not a replacement for an up-to-date repair plan.
See BMW E46 M3 SMG II operation and diagnosis, F1-style gearbox comparison and automated manual clutch and gearshift control.