Tuning Wiki

The first-generation Audi R8 offered R-tronic, an electronically controlled electrohydraulic automated manual transmission, alongside a manual-shifted version. The documented 2008 R8 has a six-speed gearbox and a dry double-disc clutch; a double-disc friction clutch does not make the transmission a dual-clutch gearbox. Identify the VIN, transmission, controller and software before applying a test. Audi of America 2008 R8 self-study programme 99B703; Audi R8 owner's manual.

Documented no-shift and pressure case

Audi of America bulletin 35 17 26 / 2027842/2, dated June 2017, concerns the 2008 R8 with R-tronic. It describes reports of gears not being selectable, basic settings failing, the pump running continuously or pressure failing to build, with fault 06079 / P17BF stored in the transmission controller. The conditions and fault do not prove that every R-tronic pump or actuator complaint has the same cause.

The bulletin separates three hydraulic possibilities: an external leak, an internal leak with loss of hydraulic fluid and an internal leak with apparently correct fluid level. It describes damaged valve sealing elements as a possible cause for the last case in the covered application. A normal reservoir level or the absence of an external leak therefore does not, on its own, establish that the circuit maintains pressure.

Separate gear-recognition and paddle-switch faults

Gear recognition: Audi of America TSB 37 12 51 / 2029694/1 describes a transmission warning and failure to select a gear with P172E and/or P17BB on 2008 R8 R-tronic cars. Loss of gear recognition can prevent shifts. Audi identifies sensor defects, mismatched contact materials and poorly routed prior harness repairs as possible causes; its diagnostic branch checks gear-recognition sensors G604 and G616 and the sensor terminals, harness contacts and repair routing. Confirm the fault codes and follow the current VIN-specific test plan; neither the warning nor either code alone proves a sensor or hydraulic unit is defective.

Steering-wheel switch: Audi TSB 37 12 41 / 2028845/1 covers specified 2008–2012 R8 R-tronic vehicles up to the bulletin’s VIN cutoff where a steering-wheel shift switch does not work but manual shifting otherwise operates. Audi describes a switch contact tab that can break and calls for testing each switch and the relevant repair. This is a different diagnostic branch from a gearbox unable to select any gear; match the exact vehicle and reproduce the symptom before replacing parts.

Diagnostic evidence

  1. Record exact vehicle and gearbox identification, fault codes and status, warning, pump behaviour, selected and reported gear and conditions before clearing faults or initiating basic settings.
  2. Using current Audi procedures, distinguish pump command, electrical supply and pressure feedback. Inspect the hydraulic circuit and level in the specified system state, and determine whether fluid loss is external or an internal branch requires investigation. Check the sensor and wiring as directed; a running pump is not proof of correct pressure.
  3. Audi's bulletin describes different service branches for its three observed leak conditions, including guided system depressurisation before inspecting specific valves and seals. It is a targeted repair path for the cited symptom and 2008 application, not a general instruction to remove valves or replace an actuator on every R8. Use the current VIN-specific guided test.
  4. For an incomplete shift with adequate pressure, compare clutch and selector command and feedback and inspect the electrical, actuator, clutch and mechanical branches directed by the appropriate repair plan. An inability to run basic settings can result from an underlying fault and is not in itself a diagnosis.

Service and safety

The hydraulic accumulator may remain pressurised and active diagnostic functions can move the clutch and selector. Follow current Audi isolation, depressurisation, fluid and basic-setting procedures before opening the circuit or activating components. Audi's bulletin notes different repair actions depending on the leak path, including a main-gearbox oil change in one specific internal-leak branch; do not assume the actuator hydraulic fluid and gearbox lubricant are interchangeable.

For other automated-manual systems see the electronic gearbox guide and automated clutch and shift control.