Tuning Wiki
Browse AiM

EVO5 is an out-of-production standalone logger that remains relevant when identifying and servicing installed motorsport systems. For the range overview see AiM in-car dataloggers.

AiM EVO5
AiM EVO5. Image: AiM, reproduced with permission; AiM product picture library.

Specifications

ItemSpecification
StatusOut of production
ECUCAN, RS232 or K-Line; second CAN
InputsEight configurable analogue inputs at up to 500 Hz each; four speed and coil RPM
Motion / GPSThree-axis accelerometer and gyro; GPS09c supplied in listed kits
Storage / enclosure4 GB internal; SD up to 128 GB; IP65

Specifications and kit contents: AiM AiM EVO5 technical documentation. Check hardware generation and exact kit.

Pinout

AiM's EVO5 sheet shows 37-pin and 22-pin Deutsch male connectors in external device view. RS232 on this EVO5 sheet is pin 21 TX and pin 22 RX; do not substitute the MXG 1.3 assignments.

Main 37-pin

PinFunction
19–15 V power input
2Battery ground
3CAN+ expansion
4Ground
5+Vbattery CAN
6CAN− expansion
7+Vb external
8CAN1+ ECU
9CAN1− ECU
10Ground
11K-Line ECU
12USB D+
13USB D−
14Ground
15RPM
16Ground
17+Vbattery
18Optical lap
19Speed 1
20Ground
21+Vbattery
22Analogue input 1
23Analogue ground
24+Vbattery
25+Vreference
26Analogue input 2
27Analogue ground
28+Vbattery
29+Vreference
30Analogue input 3
31Analogue ground
32+Vbattery
33+Vreference
34Analogue input 4
35Analogue ground
36+Vbattery
37+Vreference

Additional 22-pin

PinFunction
1Analogue input 5
2Analogue ground
3+Vbattery
4+Vreference
5Analogue input 6
6Analogue input 7
7Analogue ground
8+Vbattery
9+Vreference
10Analogue input 8
11Speed 2
12Ground
13+Vbattery
14Speed 3
15Speed 4
16Ground
17CAN2+ ECU
18CAN2− ECU
19Digital output 1
20Digital output 2
21RS232 TX
22RS232 RX

Wiring and installation

EVO5 example ECU and power wiring
EVO5 example ECU and power wiring; original Tuning Wiki illustration based on AiM documentation. Schematic diagrams do not show physical connector positions unless explicitly labelled.

AiM lists 37-pin harness V02586020 and 22-pin harness V02586030; kit and accessory contents vary. Configure the ECU protocol in Race Studio 3 before connecting CAN, serial or K-Line, as AiM's installation instructions specify.

Choose the correct model-specific lead and configure the ECU protocol in Race Studio 3. A connector shape alone does not establish vehicle compatibility. Confirm every cavity number, signal level, ground, power source and electrical limit in the linked AiM documentation before wiring; diagrams are from the device view or a conceptual schematic as stated. Secure the loom and make connections with power disconnected.

Software and further reading

Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors
Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors. Image: AiM, reproduced with permission; manufacturer source.

Analysis and download: AiM documents downloading EVO5 recordings by USB, Wi-Fi or by inserting its SD card into the PC. Select a recorded session in Race Studio 3 to review and compare the available channels. AiM model guidance. Download the Windows software from AiM Race Studio 3 software downloads. For capabilities and compatibility see AiM data-log analysis software.

Use AiM Race Studio 3 to configure supported devices and analyse recorded sessions. Check the specific ECU protocol and cable before connection; not every source exposes every channel. Manufacturer references: model documentation; product and installation guidance.