This guide covers a high-pressure fuel pump (HPFP) and rail conversion for BMW N47-family diesel engines, using the larger CP4.2 pump type also used on N57 engines. It uses Darkside Developments' complete kits as a documented example. Confirm the exact engine variant, existing components and kit with the supplier using the VIN; N47, N47N, N47S and N47S1 are not interchangeable descriptions.
Why change the pump and rail?
BMW describes the N47TU's CP4.1 as a single-piston pump and the N57TU's CP4.2 as a two-piston pump. Darkside's N47 kits use a CP4.2 as the upgrade base and replace the rail and high-pressure pipes because the rail-to-injector union size differs. The aim is additional fuel-system capacity for a suitable modified engine; the pump alone does not guarantee a power figure. BMW N57TU training manual, fuel preparation (mirror); Darkside N47 kit.
Donor identification: CP4.2 is an N57 pump type, but the kit descriptions consulted do not identify an exact N57 donor pump or state that their replacement rail is a complete standard N57 six-cylinder rail. Do not assume any N57 pump or rail will fit: confirm pump, rail, mounting, connections and part numbers with the kit supplier. A four-injector installation needs the correct rail and lines for that conversion.
N57 part-number references and pictures
These are identified N57 donor parts, not a verified shopping list for the N47 conversion. The available Darkside kit listings do not specify their supplied pump or rail part numbers, and the sources below establish original N57 application rather than fitment to an N47. Confirm the exact N47 variant, injector type, mounting, pipes and intended rail arrangement with the conversion supplier before ordering.
| Part | Identified number | Evidence and conversion status |
|---|---|---|
| N57 CP4.2 exchange pump | BMW 13 51 8 577 654 (13518577654) | Listed as a CP4.2 exchange pump for selected N57 vehicles including E90 LCI 325d/330d. N47 conversion compatibility and whether Darkside supplies this specific number are unverified. Pump listing and photograph. |
| N57 fuel rail / pressure accumulator | BMW 13 53 7 805 423 (13537805423); Bosch 0 445 216 036 | Listed for an N57 X5 30dX; Bosch's cross-reference links these BMW and Bosch numbers. A complete N57 rail's suitability, port arrangement and required modifications for the four-cylinder N47 are unverified. It is not established as the rail in Darkside's kit. N57 parts catalogue; Bosch diesel catalogue; Rail photographs. |
| Original N47 rail replaced by Darkside kit | BMW 13 53 7 809 127 (13537809127) | Darkside lists this as a rail the N47 kit replaces. It is the original application reference, not the upgrade rail number. Darkside N47 kit. |
Darkside identifies BMW 13537801992 as a standard replacement pressure regulator for its upgraded rail; that is the regulator number, not a rail assembly number. Its N47 listing identifies original pumps 13517797876, 13517812051 and 13518577643 as units the kit upgrades, not the new CP4.2 pump number. Darkside N47 kit listing.

N47D20 common-rail system display; this photograph illustrates the original system, not the N57 conversion or the components identified above. Photograph by Autotir, Wikimedia Commons, CC BY-SA 4.0; unmodified.
Kit and variant differences
- N47: Darkside lists a CP4.2-based kit with a replacement used rail, sensor and regulator, four injector pipes and two pump-to-rail pipes. The supplier states that its kit requires its N47 solenoid injector upgrade and will not fit standard injectors. It lists selected E81/E82/E87N/E88 and E90/E91 116d, 118d, 316d and 318d applications; check its full vehicle list and VIN. N47 kit and fitment list.
- N47N: The separate N47N kit is also specified with Darkside's solenoid injector upgrade. Its listed fitments include selected BMW and MINI models; engine designation and individual vehicle matter. The kit includes a used rail with sensor and regulator, four injector pipes and two pump-to-rail pipes. N47N kit and fitment list.
- N47S / N47S1: Darkside sells separate kits for these piezo-injector variants and says its kits can be used with standard or upgraded injectors. This does not override the different requirement for its N47 and N47N kits. N47S kit; N47S1 kit.
Kit contents and pump condition depend on the selected purchase option. Darkside describes new, tested used and untested used pump options, and used rails removed from running engines. Confirm the actual supply and condition before ordering.
Installation considerations
High-pressure common-rail fuel can cause serious injection injury. Have a qualified diesel specialist depressurise, dismantle and test the system using the applicable BMW repair information and kit instructions; never check for a leak with a hand or loosen a pressurised pipe. Maintain cleanliness and use the correct specified pipes, seals, fasteners and tightening procedures.
For its N47 kit Darkside specifies a special pump removal tool and clearance work to the alternator bracket and inlet manifold. Its listing also says the EGR and cooler must be removed for that kit. This has emissions and road-use implications; check the law and suitability for the intended vehicle before proceeding. For its N47N kit the supplier says no grinding is required, but the pump-to-rail pipes require manipulation and the inlet manifold must be removed. Follow the current supplier instructions for the exact kit; do not extrapolate these details to other variants. N47 fitting notes; N47N fitting notes.
Calibration and verification
Confirm sensor and regulator compatibility, connector configuration, injector type and pressure ratings for every installed component. Darkside says its supplied N47/N47N rail sensor needs upgrading if running above 2,150 bar; this is a supplier-specific threshold, not permission to run that pressure or a rating for the rest of the system. The permitted operating range is limited by the complete installation and its calibration.
Before increasing load, investigate existing fuel-system faults and check the low-pressure supply, fuel quality and any contamination. After installation, prime and leak-check according to the repair procedure, check fault codes and compare requested and actual rail pressure through idle and progressively increasing load. A tuner should validate pressure control and injector calibration for the actual hardware, rather than assuming a larger pump or sensor automatically requires or permits a higher pressure. Stop testing if pressure control is unstable or a leak is found.
Darkside reports over 270 bhp on one 118d with this kit, upgraded injectors, a GTB2260VK turbo kit and other modifications. That is a supplier example of a complete build, not the pump's standalone gain or a guaranteed result. Darkside N47 example.
Related pages and sources
- BMW N47 engines and BMW N57 engines.
- BMW N57TU engine training manual (mirror), fuel preparation and CP4.2 control.
- Darkside Developments: N47, N47N, N47S and N47S1 CP4 upgrade kits, accessed 18 November 2026.