Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Prop Shafts
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

A prop shaft, or propeller shaft, carries torque along the vehicle. In a typical rear-wheel-drive layout it connects the gearbox output to the rear final drive. A four-wheel-drive transfer box may drive separate front and rear prop shafts. The joints accommodate movement and operating angles between the connected units. Dana uses the term driveshaft for this assembly in its manuals. Dana prop shaft installation manual

Main types

One-piece shaft. A single shaft spans the distance between the units.Two-piece or multi-piece shaft. A centre support bearing locates the intermediate section. Its rubber support can degrade separately from the bearing.Joints and sliding sections. Depending on the design, the shaft may use single universal joints, a paired double-Cardan joint or CV joints. A slip spline or sliding joint can accommodate changes in installed length.

Dana prop shaft service manual

Common faults and clues

Take-up clunk or squeak. Inspect universal joints for looseness or binding, along with the flange fixings and slip splines. Differential backlash and mounts can also contribute to a clunk.Vibration or rumble. Check the centre bearing and its rubber support on multi-piece shafts. A dented tube, missing balance weight, excessive runout, poor joint angles or incorrect phasing can all produce vibration.Vibration after work. Check the vehicle’s alignment and phasing marks, shaft seating and specified joint angles. Phasing is the rotational relationship between the yokes. Correct the installation before assuming the shaft needs balancing.

Dana universal-joint service guide · Dana shaft balance guidance

Browse the related subjects in Drivetrain.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Prop shafts: layouts, joints and common faults

A prop shaft, or propeller shaft, carries torque along the vehicle. In a typical rear-wheel-drive layout it connects the gearbox output to the rear final drive. A four-wheel-drive transfer box may drive separate front and rear prop shafts. The joints accommodate movement and operating angles between the connected units. Dana uses the term driveshaft for this assembly in its manuals. Dana prop shaft installation manual

Main types

  • One-piece shaft. A single shaft spans the distance between the units.
  • Two-piece or multi-piece shaft. A centre support bearing locates the intermediate section. Its rubber support can degrade separately from the bearing.
  • Joints and sliding sections. Depending on the design, the shaft may use single universal joints, a paired double-Cardan joint or CV joints. A slip spline or sliding joint can accommodate changes in installed length.

Dana prop shaft service manual

Common faults and clues

  • Take-up clunk or squeak. Inspect universal joints for looseness or binding, along with the flange fixings and slip splines. Differential backlash and mounts can also contribute to a clunk.
  • Vibration or rumble. Check the centre bearing and its rubber support on multi-piece shafts. A dented tube, missing balance weight, excessive runout, poor joint angles or incorrect phasing can all produce vibration.
  • Vibration after work. Check the vehicle’s alignment and phasing marks, shaft seating and specified joint angles. Phasing is the rotational relationship between the yokes. Correct the installation before assuming the shaft needs balancing.

Dana universal-joint service guide · Dana shaft balance guidance

Browse the related subjects in Drivetrain.

Revision 1: Prop shafts: layouts, joints and common faults

A prop shaft, or propeller shaft, carries torque along the vehicle. In a typical rear-wheel-drive layout it connects the gearbox output to the rear final drive. A four-wheel-drive transfer box may drive separate front and rear prop shafts. The joints accommodate movement and operating angles between the connected units. Dana uses the term driveshaft for this assembly in its manuals. Dana prop shaft installation manual

Main types

  • One-piece shaft. A single shaft spans the distance between the units.
  • Two-piece or multi-piece shaft. A centre support bearing locates the intermediate section. Its rubber support can degrade separately from the bearing.
  • Joints and sliding sections. Depending on the design, the shaft may use single universal joints, a paired double-Cardan joint or CV joints. A slip spline or sliding joint can accommodate changes in installed length.

Dana prop shaft service manual

Common faults and clues

  • Take-up clunk or squeak. Inspect universal joints for looseness or binding, along with the flange fixings and slip splines. Differential backlash and mounts can also contribute to a clunk.
  • Vibration or rumble. Check the centre bearing and its rubber support on multi-piece shafts. A dented tube, missing balance weight, excessive runout, poor joint angles or incorrect phasing can all produce vibration.
  • Vibration after work. Check the vehicle’s alignment and phasing marks, shaft seating and specified joint angles. Phasing is the rotational relationship between the yokes. Correct the installation before assuming the shaft needs balancing.

Dana universal-joint service guide · Dana shaft balance guidance

Browse the related subjects in Drivetrain.