Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Driveshafts
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

A driveshaft in this guide is an axle halfshaft, also called a sideshaft. It carries torque from a transaxle or axle differential to a driven wheel. On independent suspension, constant-velocity (CV) joints allow the shaft to transmit torque while the suspension moves and, at a steered wheel, while the wheel turns. GKN sideshaft overview

Main types

Jointed halfshafts. A common layout uses a fixed ball CV joint at the wheel and a plunging joint inboard. The outer joint allows a high steering angle. The inner joint slides along its axis to accommodate changes in the distance between the differential and the hub. Inner joints may be tripod or ball designs.Live-axle halfshafts. On a conventional non-steering live axle, shafts run inside the axle housing. The differential and wheel ends move with the axle assembly. Steered live axles can still use joints at the wheel ends.

GKN CV joint designs · Dana axle service references

Common faults and clues

Split boot or loose clamp. Grease around the joint or wheel arch can reveal a leak. Water and grit can enter the joint. Inspect joint condition before deciding whether a boot alone is enough.Clicking when turning under power. Inspect the outer CV joint, especially when the noise repeats with wheel rotation. A shudder that appears under acceleration and eases when the throttle is released can point to an inboard joint. Check tyres, wheel bearings and mounts when symptoms overlap.Clunk or visible damage. Inspect the shaft, splines and fixings for wear, impact damage or poor seating. After replacement, verify that shaft length, splines and fixings match the vehicle.

GKN on boot sealing · GKN workshop resources

Browse the related subjects in Drivetrain.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Driveshafts: halfshafts, CV joints and common faults

A driveshaft in this guide is an axle halfshaft, also called a sideshaft. It carries torque from a transaxle or axle differential to a driven wheel. On independent suspension, constant-velocity (CV) joints allow the shaft to transmit torque while the suspension moves and, at a steered wheel, while the wheel turns. GKN sideshaft overview

Main types

  • Jointed halfshafts. A common layout uses a fixed ball CV joint at the wheel and a plunging joint inboard. The outer joint allows a high steering angle. The inner joint slides along its axis to accommodate changes in the distance between the differential and the hub. Inner joints may be tripod or ball designs.
  • Live-axle halfshafts. On a conventional non-steering live axle, shafts run inside the axle housing. The differential and wheel ends move with the axle assembly. Steered live axles can still use joints at the wheel ends.

GKN CV joint designs · Dana axle service references

Common faults and clues

  • Split boot or loose clamp. Grease around the joint or wheel arch can reveal a leak. Water and grit can enter the joint. Inspect joint condition before deciding whether a boot alone is enough.
  • Clicking when turning under power. Inspect the outer CV joint, especially when the noise repeats with wheel rotation. A shudder that appears under acceleration and eases when the throttle is released can point to an inboard joint. Check tyres, wheel bearings and mounts when symptoms overlap.
  • Clunk or visible damage. Inspect the shaft, splines and fixings for wear, impact damage or poor seating. After replacement, verify that shaft length, splines and fixings match the vehicle.

GKN on boot sealing · GKN workshop resources

Browse the related subjects in Drivetrain.

Revision 1: Driveshafts: halfshafts, CV joints and common faults

A driveshaft in this guide is an axle halfshaft, also called a sideshaft. It carries torque from a transaxle or axle differential to a driven wheel. On independent suspension, constant-velocity (CV) joints allow the shaft to transmit torque while the suspension moves and, at a steered wheel, while the wheel turns. GKN sideshaft overview

Main types

  • Jointed halfshafts. A common layout uses a fixed ball CV joint at the wheel and a plunging joint inboard. The outer joint allows a high steering angle. The inner joint slides along its axis to accommodate changes in the distance between the differential and the hub. Inner joints may be tripod or ball designs.
  • Live-axle halfshafts. On a conventional non-steering live axle, shafts run inside the axle housing. The differential and wheel ends move with the axle assembly. Steered live axles can still use joints at the wheel ends.

GKN CV joint designs · Dana axle service references

Common faults and clues

  • Split boot or loose clamp. Grease around the joint or wheel arch can reveal a leak. Water and grit can enter the joint. Inspect joint condition before deciding whether a boot alone is enough.
  • Clicking when turning under power. Inspect the outer CV joint, especially when the noise repeats with wheel rotation. A shudder that appears under acceleration and eases when the throttle is released can point to an inboard joint. Check tyres, wheel bearings and mounts when symptoms overlap.
  • Clunk or visible damage. Inspect the shaft, splines and fixings for wear, impact damage or poor seating. After replacement, verify that shaft length, splines and fixings match the vehicle.

GKN on boot sealing · GKN workshop resources

Browse the related subjects in Drivetrain.