Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

What the function controls

Scope: These are documented or community-definition examples, not a universal map list for every Simos 18. Check the exact ECU, ASW, CAL, gearbox, patch and definition revision. Names, available functions, axis scaling, selectors and addresses vary. A calibration value or logger signal is not automatically a safe setting. None of the examples is a ready-made tune.

Pops and bangs on lift-off are commonly implemented using an impulse-combustion request and related ignition and injection behaviour. The indexed indexed Continental EA888 Simos 18.1 function reference identifies project VW Simos 18.1 EA888, baseline SC8L50Y0, ENOS Backfire Operation State, module AE501Z01.00G. The following are examples from that baseline and the ENOS Backfire Operation State reference; they must be verified in the target ASW and its matched A2L or map definition.

Activation and conditions: calibration identifiers

  • lc_imp_comb — switch allowing impulse-combustion activation.
  • clf_conf_imp_comb_aux — drive-mode selection bitmask. Its bit meanings are version-specific; verify the definition before interpreting a mode.
  • c_conf_imp_comb_aux — condition relating activation to the sound-flap state.
  • c_n_min_imp_comb and c_n_max_imp_comb — lower and upper engine-speed thresholds in the documented baseline.
  • c_tco_min_imp_comb, c_tco_max_imp_comb, c_temp_cat_imp_comb_min, c_temp_cat_imp_comb_max, c_temp_imp_comb_min and c_temp_imp_comb_max — coolant and catalyst/exhaust-temperature conditions. Check the matching definition and whether the source is measured or modelled.

Duration, pattern and ignition

  • ip_t_act_imp_comb_eng and ip_t_act_imp_comb_eng_spt — engine-state activation time tables; the reference describes rpm and gear axes and gearbox-type selection. Do not assume the array index without checking the matching definition: community listings differ.
  • ip_t_max_pu_end_imp_comb — time window after trailing-throttle onset in which an engine-state request can be triggered; it is distinct from the activation duration itself.
  • id_nr_pat_scc_imp_comb — fuel shut-off pattern index as a function of rpm and gear in the cited baseline. It is a pattern selector, not a spark-angle table. The pattern meanings need the matching SCC documentation.
  • ip_fac_t_act_imp_comb — factor affecting duration with dynamic modelled catalyst temperature; ip_t_dly_temp_cat_imp_comb concerns the reactivation delay when the catalyst is hot.
  • ip_iga_imp_comb_sof_act and ip_iga_imp_comb_sof_deac — late impulse ignition-angle map families for active/inactive sound-flap states in the separate SC8S5031_C_OEM community cross-reference, the IGSP ignition-angle reference. The example axes are rpm and air mass. Its XDF and reference labels are potentially ambiguous about physical open versus closed; verify flap-state interpretation and array selection on the target software.

The bri3d/a2l2xdf community definition list supplies additional community names for some of these entries. Do not copy a displayed angle, cut pattern, bitmask or address from a different file. Preserve and validate the actual thermal and component protections.

Check a non-working request

Where supported, log lv_imp_comb_ena (enabled), lv_imp_comb_eng (engine/load-change request), lv_imp_comb_temp_ena (temperature enable), lv_imp_comb (active) and nr_pat_scc_imp_comb (selected fuel-cut pattern). These are measurements, not tunable maps. Compare them with rpm, drive mode, gear, actual ignition and injection/fuel-cut state. The ENOS Backfire Operation State reference lists these distinctions. A Simos 18.1 forum case illustrates why a request for late spark does not prove it was delivered or that fuel remained present.

Patch-specific controls

The simos.app Main Patch documentation adds per-slot Pops & bangs, Pops duration and Pops intensity. Its documented global Injection time, Minimum load and Spark cut controls apply when impulse combustion is active. They are patch labels, not OEM map names. The vendor says OEM overrun, speed and temperature conditions continue to gate the function. Extra exhaust heat and a raised overrun air floor are material to the calibration.

Related: switchable maps · pops and bangs · crackle tuning · DSG shift sounds.

For normal overrun cut and fuel resumption, see deceleration fuel cut.

References reviewed 17 November 2026; indexed community or function-reference material does not establish that every ECU contains the same functions.

Example from a Simos 18.1 file comparison

Scope of example: A user-supplied comparison of a Simos 18.1 stock file, Stage 1 and Stage 1 pops-low, with a WinOLS CSV definition export. LTEditor identified box code 5G0906259E and software 111SC800H6G00000. The files and definitions are not publicly available, so this is a single, independently unverified file-comparison observation, not a recommended calibration. The source’s stock values matched supported byte and 16-bit entries after accounting for table transposition. Selection, runtime logic, operating conditions and checksum suitability were not independently established.

Relative to the standard Stage 1 file, lc_imp_comb changed from 0 to 1; selected id_nr_pat_scc_imp_comb entries from 1 to 44; selected id_t_min_pu entries from 0 to 3 seconds; and selected ip_t_max_pu_end_imp_comb entries from 2 to 4 seconds. Minimum-ignition-angle families contain changes of −11.25 to −33 crank degrees. Together these are consistent with an overrun sound strategy, but a pattern index is not a decoded cut pattern, time in PU is not necessarily time in fuel cut, and an activation window is not itself sound duration.

The entry labelled c_tco_min_imp_comb changed from −48 to 143.25 °C. Taken literally this appears counterintuitive; verify the target definition, selection and state logic before interpreting when the mode can operate. Confirm impulse-combustion state, injection or fuel-cut status, actual ignition, gear, mode and temperatures in suitable logs.