Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Simos 4S is an early Volkswagen Group petrol engine-management designation. A Volkswagen Passat workshop manual shows separate Simos 4S and 4S2 identification examples for particular engines, while VW's 1995 throttle-control training programme shows a Simos 4S diagnostic display. These are scoped examples rather than a complete fitment list. Record the actual ECU part number, system designation, program level and coding before choosing a diagnostic or calibration definition.

Documented identification examples

The VW Passat Simos workshop procedure shows a Simos 4S diagnostic identification example under engine codes ADY and AGG, and a Simos 4S2 example under AFT. The manual distinguishes the controller part number, system designation, program level and coding in the tester display. Its reproduced AFT example gives inconsistent program-level numbers in the display and explanation, so read and record the value from the actual unit rather than copying it.

A TRW diagnostic coverage list also lists Simos 4S for a Vento ADY example, but the same list has a Simos 2 entry for that model and code. Such tool entries describe a product's coverage and do not resolve the controller fitted to a particular car. Do not assume 4S, 4S2 and Simos 2 files or diagnostic procedures are interchangeable.

Cable throttle and idle control

In Volkswagen SSP 173, the throttle-control training example uses a cable for driver load input and an electric throttle positioner in the idle-control range. The programme identifies throttle potentiometer G69, positioner potentiometer G88, idle switch F60 and positioner motor V60. The ECU uses their feedback for idle and throttle closing; VW uses a Simos 4S display to illustrate self-diagnosis. This training description is not evidence that every 4S installation has identical components or diagnostic channels.

SSP 173 describes different fallback responses for different signal failures: for example, missing G69 can lead to a substitute value derived from engine speed and air mass, whereas missing G88 leads to the mechanical idle fallback. A similar high-idle symptom can therefore have different causes. Save fault codes and conditions and follow the vehicle-specific workshop test before attributing the complaint to a calibration.

Fuel-pressure baseline on the Passat example

In the VW Passat Simos workshop procedure, the fuel-pressure regulator is referenced to intake-manifold pressure. For the documented test, the manual gives approximately 2.5 bar at idle, rising to approximately 3.0 bar when the regulator vacuum hose is removed on the ADY and AGG examples. It also specifies at least 2.0 bar residual pressure after 10 minutes with the ignition off. These are service checks under the manual’s stated conditions, not ECU map values or universal targets for every Simos 4S installation.

The manual relates a low idle-pressure result to a check of pump delivery, and its holding-pressure diagnosis also considers leaks at the gauge, connections, injectors and pump non-return valve. A pressure result alone does not prove which part is faulty. Before interpreting a mixture or injector-duration problem as a calibration issue, use the vehicle-specific service procedure and its correct equipment and safety precautions; confirm fuel pressure and regulator response alongside the air, ignition and lambda checks.

Passat ADY/AGG lambda and adaptation display

The reproduced Passat ADY and AGG display-group overview distinguishes an additive learned lambda value at idle from a multiplicative learned value at part and full load in group 06. The same group also includes learned idle-control positioner values; they are not lambda corrections. The manual warns that the group 00 additive adaptation display does not reveal whether the idle mixture is being adapted rich or lean. Do not assume that a positive displayed value means a conventional positive percentage fuel trim or use it alone to diagnose a lean condition.

For the manual's lambda functional check, the engine idles with coolant at least 80 °C and no exhaust leak between cylinder head and catalyst. It checks the control status in group 05 and the probe voltage in group 01; for ADY and AGG it specifies a fluctuating voltage within 0–1.1 V at least 30 times per minute. AFT has a different stated range. This historical workshop test and its status bits are specific to the described system and test conditions, not a wideband air-fuel ratio reading or a universal criterion for every Simos logger. Confirm the exact controller and the current diagnostic procedure.

The same manual's self-diagnosis description says a lambda-control function fault can be interrogated only after a test drive of at least 10 minutes. Record faults and operating conditions before clearing them; a fault-free scan alone does not prove that a monitor has completed. Investigate the sensor, exhaust and intake leaks, fuel supply and operating conditions before changing an injection map.

Baseline and calibration work

  1. Record the exact ECU identification, engine and gearbox, fuel, modifications, complete fault scan and recent work. Check throttle cable operation, idle-switch and potentiometer signals, intake leaks, air-meter plausibility, ignition and fuel delivery as appropriate.
  2. For the throttle-control example, VW describes learned deviations and a basic setting after replacement of the throttle unit or ECU. It is a training example, not a universal procedure for all controllers or repairs. Follow the current workshop instructions and verify the reported result; do not mechanically adjust sealed sensors or indiscriminately clear learned values.
  3. Where the actual diagnostic tool supports them, compare engine speed, throttle and idle-switch state, air mass, lambda and ignition-related values under repeatable conditions. Confirm units and whether a value is measured or calculated. A scanner's ability to read a fault or measuring block does not establish calibration read or write support.
  4. Match definitions, file layout and programming method to the exact controller and software. Confirm original-data scope, checksum handling, stable supply and recovery for the selected tool. The sources here do not identify performance-map addresses, axes or numerical tuning changes.

One supplier advertises separate four-map CSV exports for a Golf 3 2.0 Simos 4S and a 1.6 Simos 4S2 example. Both listings use labels for closed- and part-throttle spark, part-throttle injection and an engine-speed limiter. They do not show ECU part or software numbers in the public listing; despite the seller's request to match them, the page alone is insufficient to establish whether either export matches the ECU in hand. The names and functions are seller claims, not independently verified maps, addresses or an instruction to change a limiter. The supplier describes a CSV export, not an original factory DAMOS or A2L, and says its supplied file excludes EEPROM.

Sources