Early Simos context
Volkswagen Self-Study Programme 165, December 1994, introduces early Simos as the engine-management system that follows Digifant. Load comes from the air-mass meter and from engine speed. From those two, the control unit calculates injection duration and ignition timing, then applies the corrections. The functions named in that programme are cylinder-selective knock control, lambda control, idle control on the air side through the throttle control unit and by ignition timing, and charcoal-canister control. The programme says the functions are adaptive. This early description does not itself identify the controller as Simos 3; see Simos 4S for separately documented early examples.
The crankshaft sensor in that system is a Hall sensor on a toothed wheel. The VR6 of the same period used an inductive sender for the same job. If the speed signal is lost, the fuel pump is switched off: the engine does not start, or it stalls. The programme is a teaching text. The workshop literature is the procedure for the car in front of you.
Simos 3.3 on the APF
Self-Study Programme 222 identifies a numbered Simos variant on a specific engine. The electronically mapped cooling system appears first on the 1.6-litre inline-four, code APF, 74 kW. The programme says further engines were in preparation, and it names Simos 3.3 as the engine management that contains the cooling functions.
The maps it lists inside that controller are a coolant-temperature setpoint from engine speed and load, a second setpoint from road speed and intake-air temperature, a pre-control duty factor from the setpoint and engine speed, and two maps for the temperature difference that brings in the radiator fan at its first and second speed. The controller drives the heater in the thermostat and the two fan outputs. It reads the radiator return temperature and the potentiometer at the heater controls. The rest of the engine sensors already on the controller supply the other inputs. A Simos 3.3 label on a different engine is not, by this programme, the APF installation.
For the APF temperature setpoint selection, thermostat and fan fallbacks, and a logging workflow, see Simos 3.3 APF mapped cooling calibration and logs.
Simos 3.3 on Octavia AVU and BFQ
The Škoda Octavia Mk1 workshop equipment table identifies Simos 3.3 on the 1.6-litre, 75 kW AVU and BFQ engines. For these specific applications it lists electronic throttle control, two lambda probes, knock control, exhaust gas recirculation and self-diagnosis. The engine data table also lists intake-manifold changeover and secondary air. These details do not establish identical equipment on every Simos 3.3 installation.
The component overview shows the air-mass meter G70 with intake-air temperature sender G42, throttle control unit J338 and EGR valve N18 with position sensor G212. It places the camshaft position sensor in different locations on AVU and BFQ; consult the correct engine-specific procedure when tracing a fault.
Diagnosis and calibration scope
Read and record engine fault codes and operating conditions before changing calibration. Where supported, compare throttle and pedal behaviour, air mass, lambda feedback, fuel trims, ignition and temperatures. Confirm a diagnostic value's units and conditions before drawing a conclusion, and check for air leaks, wiring and mechanical faults alongside any software investigation.
The workshop's AVU/BFQ engine installation procedure calls for adaptation to the throttle control unit and EGR valve and a readiness check; that requirement is scoped to the described work. Its secondary-air readiness test gives different operator instructions for AVU and BFQ. Use the exact current workshop and diagnostic procedure for the engine and job, rather than assuming that similar Simos labels make basic settings interchangeable.
Keep the controller's hardware, software and calibration identification with any original read and use a definition verified for that software. These sources document operation and diagnosis; they do not establish performance map addresses, scaling or safe ignition and fuelling changes.
Chip-read representation and calibration editing
In a Simos 3.3A Octavia discussion, an owner identifies a 2005 BFQ car and reports reading an AM29F400B flash device. A respondent describes a data-line-swapped representation for a chip read, while the owner later questions whether candidate pedal maps have been correctly identified. The shared files and claimed map functions were not independently verified, and the discussion does not establish that every Simos 3 read or tool output uses the same representation.
EVC’s WinOLS manual describes line swapping or inversion on import, export and EPROM operations; it distinguishes readable project data from the representation produced for export. Its older manual shows a VAG Simos 3 preset as an example. Neither the existence of that preset nor a plausible-looking map proves that it should be applied to an unknown read: an OBD or bench tool may already output data in the representation expected by an editor. Identify the source, tool and format first, preserve the unchanged read, and check a no-edit import/export against it in the same representation. Confirm checksum coverage and the intended programming format with the relevant tool provider; a valid checksum alone does not establish correct data ordering, file identity or map function.
Other Simos 3 suffixes
An OBDSTAR coverage note lists Simos 3.3A, 3.4A and 3PA through 3PG as Siemens memory layouts for Audi, SEAT, Škoda and Volkswagen, each described with an external flash and an EEPROM. That list is what the tool claims to address. It is not a vehicle fitment list, and those suffixes are not Simos 18 or Simos 19. The number after Simos is read from the controller, then matched to the software of that car.
Later Volkswagen direct-injection petrol engines were also run by Bosch MED controllers. SSP 253 is the Bosch Motronic MED 7 account of petrol direct injection. A direct-injection Volkswagen is not automatically a Simos.
1.2-litre three-cylinder identification examples
A reproduced SEAT workshop technical-data table lists Simos 3PE for the 1.2-litre AZQ and BME column, Simos 3PG for a separate BME column and Simos 9.1 for its BXV column. Its listing of BME under two controllers is a concrete reason not to choose a calibration on engine code alone. It does not identify the software version or establish interchangeability between those units.
The VW Polo 2002-on 1.2-litre workshop manual, July 2015 edition, groups AWY/BMD/BBM with 3PD and 3PG, and AZQ/BME/BZG with 3PE and 3PG. Its grouped table does not assign each engine to one suffix. For a file or diagnostic procedure, read the actual controller identification and consult the applicable parts and workshop information. Neither table supplies validated performance-map axes or addresses.
Škoda 1.2 MPI: Simos 3PD and 3PE lambda control
Škoda Self-Study Programme 45, pages 21–24, describes its early 1.2-litre three-cylinder MPI examples as Simos 3PD at 40 kW and 3PE at 47 kW. In that training example the 3PD uses switching probes both before and after the catalyst; the 3PE uses a broadband upstream probe and a switching downstream probe. The programme describes injection correction from the upstream sensor and a second control circuit using the downstream sensor to adapt upstream probe characteristics within a defined range. Do not treat the downstream signal as interchangeable with the upstream measurement. Confirm sensor type, location, signal and diagnostic units for the actual vehicle before judging mixture or a log.
On these examples intake temperature G42 and manifold pressure G71 provide information used in calculating injection time and ignition timing; the throttle is electronically controlled. SSP 45 describes a maximum attainable speed of approximately 5,820 rpm, with injection and fuel pump shutoff at or above 5,920 rpm if the engine is driven beyond that limit. These are the training example's behaviours, not universal Simos 3 limit values or a verified map address. The programme also says a running engine stops if crankshaft speed sender G28 fails but can be restarted using the camshaft sender G163 as a substitute; loss of both prevents restart. Check faults and sensor status before treating an unusual start, speed limit or mixture correction as a calibration issue.
These examples complement the workshop tables above; later 3PG applications cannot be assigned the same probe types or thresholds from SSP 45 alone. The source does not provide a definition file, map axes, scaling or calibration values for tuning.
Sources
- Škoda Self-Study Programme 45: 1.2-litre three-cylinder engine, pages 21–24. 3PD/3PE lambda control, example speed control and sender fallback. Training document; verify the actual vehicle and workshop procedure. Accessed 17 November 2026.
- Nefarious Motorsports: Simos 3.3A Octavia 1.6. Community chip-read and map-identification discussion; attachments and conclusions not independently verified. Indexed discussion reviewed 17 November 2026; direct forum access unavailable.
- EVC WinOLS manual, section 6.2, and earlier WinOLS help manual, swap-lines profile illustration. Tool-specific representation and import/export context, not a universal procedure for Simos 3. Accessed 17 November 2026.
- Volkswagen / Audi Self-Study Programme 165, Simos engine management, December 1994. Successor to Digifant; load, knock, lambda, idle and canister functions. SSP 165 PDF. Catalogue note: SSP 165 record. Accessed 2026-11-13.
- Volkswagen Self-Study Programme 222, Electronically Mapped Cooling System. APF 1.6, 74 kW, and the Simos 3.3 maps for that cooling system. SSP 222 PDF. Accessed 2026-11-13.
- OBDSTAR DC706 coverage note, June 2024 software. Simos 3.3A, 3.4A and 3PA–3PG named as Siemens layouts for Audi, SEAT, Škoda and Volkswagen. Coverage note. Accessed 2026-11-13.
- Škoda Octavia Mk1 workshop manual, self-diagnosis equipment, AVU and BFQ, and engine technical data. Simos 3.3 and equipment on these 1.6-litre engines. Accessed 2026-11-17.
- Škoda Octavia Mk1 workshop manual, AVU/BFQ component overview, engine installation and secondary-air readiness test. Installation and test instructions are engine- and job-specific. Accessed 2026-11-17.