Removed text is struck through; added text is highlighted.
This guide uses Volkswagen's documented 1.2-litre, 77 kW CBZB engine with Simos 10 to explain direct-injection modes and fuel-pressure checks relevant to calibration work. The self-study programme does not specify a Simos 10 suffix or establish that every Simos 10 vehicle has the same components or calibration. Identify the actual engine, ECU and software first. VW SSP 443.
Pressure system and injector context
SSP 443's system diagram identifies low-pressure pump G6 and its controller J538, fuel pressure sender G247, fuel-pressure regulating valve N276 and direct injectors N30–N33. It illustrates a high-pressure pump supplying the rail and injectors. The programme describes six spray jets per injector and an injection pressure range of 40–125 bar for its 1.2 TSI example. That range describes the system in the training material; it is not a single desired pressure, a fault threshold or a permissible tuning target for every vehicle and operating point. Use the current workshop data for the identified engine. VW SSP 443, pages 13 and 22–24.
Pressure must be interpreted with demand, engine speed and injection timing: a satisfactory rail-pressure number alone does not prove that the injectors deliver the required quantity or that mixture is correct. Equally, a momentary difference between requested and actual pressure does not by itself identify a defective pump or prove a calibration problem. Confirm sensor and log units, sample timing and the applicable test conditions.
Workshop example: supply pressure and sender plausibility
A reproduced Škoda Roomster 1.2 TSI workshop manual, edition 02.10, identifies its CBZA and CBZB examples as Simos 10. Its low-pressure fuel-feed test specifies 4–7 bar after the prescribed ignition cycling, and a holding pressure of at least 3 bar after 10 minutes. These are low-pressure-side workshop measurements under that procedure’s specific conditions, not high-pressure rail targets or proof of adequate fuel flow at high load. The manual also describes a separate fuel-flow test that accounts for supply voltage. Use the current repair information and equipment for the specific vehicle; a pressure reading alone cannot establish pump delivery under load.
The same manual describes checking high-pressure sender G247 against a separate pressure tester with the engine running. It gives a maximum difference of 5 bar for its specified test equipment and conditions and directs further diagnosis if readings disagree. A tolerance from that workshop test is not a general limit for all log channels or vehicles; follow the current vehicle-specific high-pressure relief and test procedure. Do not open a pressurised direct-injection system to reproduce a log comparison.
Two direct-injection events
VW describes two distinct uses of split injection for the CBZB. During catalyst heating the first injection takes place during intake and the smaller second event occurs before ignition top dead centre; the programme describes an 80% first-event share for that example. It also describes split injection from idle through full load up to 3,000 rpm: the first event occurs during the intake stroke and, depending on the calibration, accounts for 50–80% of fuel; the remaining fuel is injected at the start of compression. These are two pulses of direct injection, not evidence of separate port injectors. The training description does not establish exactly when every real-world calibration selects or leaves a mode. VW SSP 443, page 24.
When comparing runs, record warm-up state, coolant temperature, time after start, speed and load. A change in engine behaviour or exhaust sound during catalyst heating can reflect a different operating mode, but does not rule out a fault. A pulse-width or injection-angle channel must be understood in context: confirm whether it represents one event, a combined value or a calculated quantity before inferring total fuel delivery.
Definition example: fuel targets during warm-up
A separate publicly indexed V2A360ZWS74 WinOLS project contains descriptions for different pressure and lambda targets. A third-party OLS reader reports ip_fup_sp_hom as a 10-by-12 fuel-pressure setpoint map for homogeneous operation and ip_fup_sp_mplh_opp as a 10-by-8 setpoint map for double injection. Engine speed is named for one axis of each; the reader did not provide a description for the other axis. The project labels are a research lead, not proof that either table was active during the factory CBZB example above.
The same reader reports separate 6-by-6 entries labelled ip_fup_rng_h_sp_ch for catalyst heating and ip_fup_rng_h_sp_mplh_ch for catalyst heating with multiple injection. Their named axis inputs are engine speed and predicted air mass used for basic injection. It likewise reports idle catalyst-heating lambda entries ip_lamb_ch_is and ip_lamb_mplh_ch_is with engine speed and limited slow-path torque request as axis descriptions. These labels illustrate why operating mode matters when comparing a logged setpoint; they do not identify an active table or prove that a change to one is required.
Definition example: pulse timing and injector correctionsFor the same V2A360ZWS74 project, the OLS reader reports ip_soi_1_mplh_ast as a 6-by-6 basic start-of-injection angle map for the first pulse after start, and ip_eoi_2_mplh_ast as a 6-by-6 basic end-of-injection angle map for the second pulse after start. It associates both with engine speed and a mean fuel-mass-flow setpoint after combustion selection. These descriptions distinguish the first event's start from the second event's end; they do not establish either pulse's full timing, duration or active operating window.The reader also reports six-point ip_ti_min and ip_ti_min_l minimum-injection-time curves, and six-point ip_ti_add_dly_hpdi and ip_ti_add_dly_hpdi_l injector dead-time correction curves; the _l descriptions specify a low-current profile. It associates each with pressure difference at the injector for the first pulse. These are separate from the fuel-pressure setpoint maps above, and are a reason to identify which pulse and current profile a reliable log or definition describes before comparing behaviour. Their presence does not prove that any is selected on a particular vehicle or that an edit is needed.The name and function descriptions are embedded in the project, while dimensions and axis association are the reader's interpretation and have not been independently validated in WinOLS or against an ECU. Project origin, usage rights, file-to-ECU compatibility, scaling and runtime behaviour are unverified. Match and verify the actual controller, binary and definition, and inspect mode and feedback in a supported log before interpreting any target. The examined project has SHA-256 60859cd3f74e1362db522b68de3a8d2c1b5b415df9d91794a338cb5b94368ba4; see the Simos 10 overview for its identification context.
What the map listing does and does not establish
For a separate SEAT Ibiza file labelled Simos 10.22, Auto-Remap's 03F906070GR 5485 listing advertises injection base, correction and enrichment labels, two requested-lambda labels and two rail-pressure labels. The public page does not show sizes, axes or positions for those maps. The seller's labels do not identify which maps control either split-injection mode described above or verify their units, scaling or operating conditions. Match and validate the exact file and definition before drawing conclusions; SSP 443 names Simos 10 but does not identify this particular file or its suffix.
Reviewing logs and diagnosing a mismatch
Record the engine code, ECU identifiers, fuel and hardware, current faults and relevant maintenance. Establish a healthy baseline before assessing an edited calibration.
Where supported, log high-pressure target and actual, engine speed and load, lambda target and measured lambda, and the fuel metering or pressure-control command. Check whether channel values are measured or calculated and whether sampling rates can capture a transient. The public CBZB N276 diagnostic listing similarly groups requested and actual high pressure with a fuel-metering value, but its numerical test criteria are not publicly displayed.
Compare matched conditions and look at the target as well as the result. If actual pressure persistently fails to follow a plausible request, investigate low-pressure supply, the control valve and electrical circuit, pressure sensor and high-pressure pump using the applicable workshop procedure. An apparent mismatch can also result from channel definition or sampling; do not replace parts based on one trace.
Review commanded and measured lambda, injection events where reliably defined, and ignition corrections alongside fuel pressure. If pressure follows its request but mixture is unexpected, pressure alone does not explain the result; check sensor validity, air and fuel delivery, and test conditions. Preserve component protections and do not assume that raising rail pressure or copying injection splits will fix a lean condition.
The fuel rail can retain hazardous pressure. Follow the vehicle-specific workshop pressure-relief and repair procedure before opening the system; the log-review process above is not a substitute for it.
Sources
Volkswagen SSP 443: 1.2 TSI 77 kW engine, French edition, especially pages 5, 13 and 22–24. CBZB Simos 10, injector description, system layout and split-injection modes. Training information, not current repair instructions.
Auto-Remap 03F906070GR 5485 map-pack listing. Seller's Simos 10.22 map labels; definitions and mode identities are not independently verified.
Vis4VAG CBZB N276 test listing. Publicly visible diagnostic channel and component categories; test values require access and are not reproduced.
Sources accessed 17 November 2026.
Open each version to inspect formatting, tables and photographs.
Revision 3: Simos 10 CBZB fuel pressure and split injection log review
This guide uses Volkswagen's documented 1.2-litre, 77 kW CBZB engine with Simos 10 to explain direct-injection modes and fuel-pressure checks relevant to calibration work. The self-study programme does not specify a Simos 10 suffix or establish that every Simos 10 vehicle has the same components or calibration. Identify the actual engine, ECU and software first. VW SSP 443.
Pressure system and injector context
SSP 443's system diagram identifies low-pressure pump G6 and its controller J538, fuel pressure sender G247, fuel-pressure regulating valve N276 and direct injectors N30–N33. It illustrates a high-pressure pump supplying the rail and injectors. The programme describes six spray jets per injector and an injection pressure range of 40–125 bar for its 1.2 TSI example. That range describes the system in the training material; it is not a single desired pressure, a fault threshold or a permissible tuning target for every vehicle and operating point. Use the current workshop data for the identified engine. VW SSP 443, pages 13 and 22–24.
Pressure must be interpreted with demand, engine speed and injection timing: a satisfactory rail-pressure number alone does not prove that the injectors deliver the required quantity or that mixture is correct. Equally, a momentary difference between requested and actual pressure does not by itself identify a defective pump or prove a calibration problem. Confirm sensor and log units, sample timing and the applicable test conditions.
Workshop example: supply pressure and sender plausibility
A reproduced Škoda Roomster 1.2 TSI workshop manual, edition 02.10, identifies its CBZA and CBZB examples as Simos 10. Its low-pressure fuel-feed test specifies 4–7 bar after the prescribed ignition cycling, and a holding pressure of at least 3 bar after 10 minutes. These are low-pressure-side workshop measurements under that procedure’s specific conditions, not high-pressure rail targets or proof of adequate fuel flow at high load. The manual also describes a separate fuel-flow test that accounts for supply voltage. Use the current repair information and equipment for the specific vehicle; a pressure reading alone cannot establish pump delivery under load.
The same manual describes checking high-pressure sender G247 against a separate pressure tester with the engine running. It gives a maximum difference of 5 bar for its specified test equipment and conditions and directs further diagnosis if readings disagree. A tolerance from that workshop test is not a general limit for all log channels or vehicles; follow the current vehicle-specific high-pressure relief and test procedure. Do not open a pressurised direct-injection system to reproduce a log comparison.
Two direct-injection events
VW describes two distinct uses of split injection for the CBZB. During catalyst heating the first injection takes place during intake and the smaller second event occurs before ignition top dead centre; the programme describes an 80% first-event share for that example. It also describes split injection from idle through full load up to 3,000 rpm: the first event occurs during the intake stroke and, depending on the calibration, accounts for 50–80% of fuel; the remaining fuel is injected at the start of compression. These are two pulses of direct injection, not evidence of separate port injectors. The training description does not establish exactly when every real-world calibration selects or leaves a mode. VW SSP 443, page 24.
When comparing runs, record warm-up state, coolant temperature, time after start, speed and load. A change in engine behaviour or exhaust sound during catalyst heating can reflect a different operating mode, but does not rule out a fault. A pulse-width or injection-angle channel must be understood in context: confirm whether it represents one event, a combined value or a calculated quantity before inferring total fuel delivery.
Definition example: fuel targets during warm-up
A separate publicly indexed V2A360ZWS74 WinOLS project contains descriptions for different pressure and lambda targets. A third-party OLS reader reports ip_fup_sp_hom as a 10-by-12 fuel-pressure setpoint map for homogeneous operation and ip_fup_sp_mplh_opp as a 10-by-8 setpoint map for double injection. Engine speed is named for one axis of each; the reader did not provide a description for the other axis. The project labels are a research lead, not proof that either table was active during the factory CBZB example above.
The same reader reports separate 6-by-6 entries labelled ip_fup_rng_h_sp_ch for catalyst heating and ip_fup_rng_h_sp_mplh_ch for catalyst heating with multiple injection. Their named axis inputs are engine speed and predicted air mass used for basic injection. It likewise reports idle catalyst-heating lambda entries ip_lamb_ch_is and ip_lamb_mplh_ch_is with engine speed and limited slow-path torque request as axis descriptions. These labels illustrate why operating mode matters when comparing a logged setpoint; they do not identify an active table or prove that a change to one is required.
The name and function descriptions are embedded in the project, while dimensions and axis association are the reader's interpretation and have not been independently validated in WinOLS or against an ECU. Project origin, usage rights, file-to-ECU compatibility, scaling and runtime behaviour are unverified. Match and verify the actual controller, binary and definition, and inspect mode and feedback in a supported log before interpreting any target. The examined project has SHA-256 60859cd3f74e1362db522b68de3a8d2c1b5b415df9d91794a338cb5b94368ba4; see the Simos 10 overview for its identification context.
What the map listing does and does not establish
For a separate SEAT Ibiza file labelled Simos 10.22, Auto-Remap's 03F906070GR 5485 listing advertises injection base, correction and enrichment labels, two requested-lambda labels and two rail-pressure labels. The public page does not show sizes, axes or positions for those maps. The seller's labels do not identify which maps control either split-injection mode described above or verify their units, scaling or operating conditions. Match and validate the exact file and definition before drawing conclusions; SSP 443 names Simos 10 but does not identify this particular file or its suffix.
Reviewing logs and diagnosing a mismatch
- Record the engine code, ECU identifiers, fuel and hardware, current faults and relevant maintenance. Establish a healthy baseline before assessing an edited calibration.
- Where supported, log high-pressure target and actual, engine speed and load, lambda target and measured lambda, and the fuel metering or pressure-control command. Check whether channel values are measured or calculated and whether sampling rates can capture a transient. The public CBZB N276 diagnostic listing similarly groups requested and actual high pressure with a fuel-metering value, but its numerical test criteria are not publicly displayed.
- Compare matched conditions and look at the target as well as the result. If actual pressure persistently fails to follow a plausible request, investigate low-pressure supply, the control valve and electrical circuit, pressure sensor and high-pressure pump using the applicable workshop procedure. An apparent mismatch can also result from channel definition or sampling; do not replace parts based on one trace.
- Review commanded and measured lambda, injection events where reliably defined, and ignition corrections alongside fuel pressure. If pressure follows its request but mixture is unexpected, pressure alone does not explain the result; check sensor validity, air and fuel delivery, and test conditions. Preserve component protections and do not assume that raising rail pressure or copying injection splits will fix a lean condition.
The fuel rail can retain hazardous pressure. Follow the vehicle-specific workshop pressure-relief and repair procedure before opening the system; the log-review process above is not a substitute for it.
Sources
Sources accessed 17 November 2026.
Revision 5: Simos 10 CBZB fuel pressure and split injection log review
This guide uses Volkswagen's documented 1.2-litre, 77 kW CBZB engine with Simos 10 to explain direct-injection modes and fuel-pressure checks relevant to calibration work. The self-study programme does not specify a Simos 10 suffix or establish that every Simos 10 vehicle has the same components or calibration. Identify the actual engine, ECU and software first. VW SSP 443.
Pressure system and injector context
SSP 443's system diagram identifies low-pressure pump G6 and its controller J538, fuel pressure sender G247, fuel-pressure regulating valve N276 and direct injectors N30–N33. It illustrates a high-pressure pump supplying the rail and injectors. The programme describes six spray jets per injector and an injection pressure range of 40–125 bar for its 1.2 TSI example. That range describes the system in the training material; it is not a single desired pressure, a fault threshold or a permissible tuning target for every vehicle and operating point. Use the current workshop data for the identified engine. VW SSP 443, pages 13 and 22–24.
Pressure must be interpreted with demand, engine speed and injection timing: a satisfactory rail-pressure number alone does not prove that the injectors deliver the required quantity or that mixture is correct. Equally, a momentary difference between requested and actual pressure does not by itself identify a defective pump or prove a calibration problem. Confirm sensor and log units, sample timing and the applicable test conditions.
Workshop example: supply pressure and sender plausibility
A reproduced Škoda Roomster 1.2 TSI workshop manual, edition 02.10, identifies its CBZA and CBZB examples as Simos 10. Its low-pressure fuel-feed test specifies 4–7 bar after the prescribed ignition cycling, and a holding pressure of at least 3 bar after 10 minutes. These are low-pressure-side workshop measurements under that procedure’s specific conditions, not high-pressure rail targets or proof of adequate fuel flow at high load. The manual also describes a separate fuel-flow test that accounts for supply voltage. Use the current repair information and equipment for the specific vehicle; a pressure reading alone cannot establish pump delivery under load.
The same manual describes checking high-pressure sender G247 against a separate pressure tester with the engine running. It gives a maximum difference of 5 bar for its specified test equipment and conditions and directs further diagnosis if readings disagree. A tolerance from that workshop test is not a general limit for all log channels or vehicles; follow the current vehicle-specific high-pressure relief and test procedure. Do not open a pressurised direct-injection system to reproduce a log comparison.
Two direct-injection events
VW describes two distinct uses of split injection for the CBZB. During catalyst heating the first injection takes place during intake and the smaller second event occurs before ignition top dead centre; the programme describes an 80% first-event share for that example. It also describes split injection from idle through full load up to 3,000 rpm: the first event occurs during the intake stroke and, depending on the calibration, accounts for 50–80% of fuel; the remaining fuel is injected at the start of compression. These are two pulses of direct injection, not evidence of separate port injectors. The training description does not establish exactly when every real-world calibration selects or leaves a mode. VW SSP 443, page 24.
When comparing runs, record warm-up state, coolant temperature, time after start, speed and load. A change in engine behaviour or exhaust sound during catalyst heating can reflect a different operating mode, but does not rule out a fault. A pulse-width or injection-angle channel must be understood in context: confirm whether it represents one event, a combined value or a calculated quantity before inferring total fuel delivery.
Definition example: fuel targets during warm-up
A separate publicly indexed V2A360ZWS74 WinOLS project contains descriptions for different pressure and lambda targets. A third-party OLS reader reports ip_fup_sp_hom as a 10-by-12 fuel-pressure setpoint map for homogeneous operation and ip_fup_sp_mplh_opp as a 10-by-8 setpoint map for double injection. Engine speed is named for one axis of each; the reader did not provide a description for the other axis. The project labels are a research lead, not proof that either table was active during the factory CBZB example above.
The same reader reports separate 6-by-6 entries labelled ip_fup_rng_h_sp_ch for catalyst heating and ip_fup_rng_h_sp_mplh_ch for catalyst heating with multiple injection. Their named axis inputs are engine speed and predicted air mass used for basic injection. It likewise reports idle catalyst-heating lambda entries ip_lamb_ch_is and ip_lamb_mplh_ch_is with engine speed and limited slow-path torque request as axis descriptions. These labels illustrate why operating mode matters when comparing a logged setpoint; they do not identify an active table or prove that a change to one is required.
Definition example: pulse timing and injector corrections
For the same V2A360ZWS74 project, the OLS reader reports ip_soi_1_mplh_ast as a 6-by-6 basic start-of-injection angle map for the first pulse after start, and ip_eoi_2_mplh_ast as a 6-by-6 basic end-of-injection angle map for the second pulse after start. It associates both with engine speed and a mean fuel-mass-flow setpoint after combustion selection. These descriptions distinguish the first event's start from the second event's end; they do not establish either pulse's full timing, duration or active operating window.
The reader also reports six-point ip_ti_min and ip_ti_min_l minimum-injection-time curves, and six-point ip_ti_add_dly_hpdi and ip_ti_add_dly_hpdi_l injector dead-time correction curves; the _l descriptions specify a low-current profile. It associates each with pressure difference at the injector for the first pulse. These are separate from the fuel-pressure setpoint maps above, and are a reason to identify which pulse and current profile a reliable log or definition describes before comparing behaviour. Their presence does not prove that any is selected on a particular vehicle or that an edit is needed.
The name and function descriptions are embedded in the project, while dimensions and axis association are the reader's interpretation and have not been independently validated in WinOLS or against an ECU. Project origin, usage rights, file-to-ECU compatibility, scaling and runtime behaviour are unverified. Match and verify the actual controller, binary and definition, and inspect mode and feedback in a supported log before interpreting any target. The examined project has SHA-256 60859cd3f74e1362db522b68de3a8d2c1b5b415df9d91794a338cb5b94368ba4; see the Simos 10 overview for its identification context.
What the map listing does and does not establish
For a separate SEAT Ibiza file labelled Simos 10.22, Auto-Remap's 03F906070GR 5485 listing advertises injection base, correction and enrichment labels, two requested-lambda labels and two rail-pressure labels. The public page does not show sizes, axes or positions for those maps. The seller's labels do not identify which maps control either split-injection mode described above or verify their units, scaling or operating conditions. Match and validate the exact file and definition before drawing conclusions; SSP 443 names Simos 10 but does not identify this particular file or its suffix.
Reviewing logs and diagnosing a mismatch
- Record the engine code, ECU identifiers, fuel and hardware, current faults and relevant maintenance. Establish a healthy baseline before assessing an edited calibration.
- Where supported, log high-pressure target and actual, engine speed and load, lambda target and measured lambda, and the fuel metering or pressure-control command. Check whether channel values are measured or calculated and whether sampling rates can capture a transient. The public CBZB N276 diagnostic listing similarly groups requested and actual high pressure with a fuel-metering value, but its numerical test criteria are not publicly displayed.
- Compare matched conditions and look at the target as well as the result. If actual pressure persistently fails to follow a plausible request, investigate low-pressure supply, the control valve and electrical circuit, pressure sensor and high-pressure pump using the applicable workshop procedure. An apparent mismatch can also result from channel definition or sampling; do not replace parts based on one trace.
- Review commanded and measured lambda, injection events where reliably defined, and ignition corrections alongside fuel pressure. If pressure follows its request but mixture is unexpected, pressure alone does not explain the result; check sensor validity, air and fuel delivery, and test conditions. Preserve component protections and do not assume that raising rail pressure or copying injection splits will fix a lean condition.
The fuel rail can retain hazardous pressure. Follow the vehicle-specific workshop pressure-relief and repair procedure before opening the system; the log-review process above is not a substitute for it.
Sources
Sources accessed 17 November 2026.