Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos 2
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Simos 2P is a Siemens petrol engine-management system documented by Volkswagen on the 1.0-litre AHT engine. It is a separate identification from the AEH and AKL Simos 2 examples in the Simos 2 overview. Identify the exact ECU, hardware and software before selecting a file, editor definition or programming method.

Documented application and identification

Volkswagen’s Self-Study Programme 203 identifies the Lupo 1.0 AHT as a 997 cm³ four-cylinder engine with Simos 2P multipoint injection. Its example is rated 37 kW at 5,000 rpm and 84 Nm at 3,250 rpm. These are factory figures for that engine, not calibration targets or proof that a particular vehicle retains its original ECU. Record the diagnostic identification, controller label, engine code and actual software.

The programme specifies 95 RON petrol for its example and says 91 RON can alternatively be used with reduced output through knock control. Follow the actual vehicle’s current fuel specification; this statement does not establish the fuel requirements of a modified calibration. Volkswagen’s Lupo SSP 201 independently identifies the AHT engine-management system as Siemens Simos 2P.

Load sensing and injection

For AHT, SSP 203 describes engine speed and intake-manifold pressure as inputs to the load calculation, with manifold air temperature also used to calculate intake air quantity. It describes the ECU calculating injection duration and ignition timing with corrections including lambda, idle and cylinder-selective knock control. These descriptions do not identify individual performance-map addresses or prove the same strategy for every Simos 2P calibration.

The documented engine has an injector upstream of each intake valve. Volkswagen describes semi-sequential paired operation: cylinders 1 and 4 are activated together, as are 2 and 3. This is port injection, not two direct-injection pulses. A shared pair command or a single lambda reading cannot establish that both injectors in that pair deliver equally; diagnose individual circuits and fuel delivery using the current workshop procedure. VW SSP 203, injection system.

Sensor fallback and knock diagnosis

In the same AHT example, manifold-pressure sender G71 and intake-air-temperature sender G42 are mounted at the intake manifold. Volkswagen says that with missing pressure signals the ECU uses throttle-position and engine-speed information with an emergency running map; if intake-air temperature is missing it uses a substitute of 45 °C. A plausible displayed value can therefore be a substitute rather than a live measurement. Check the fault memory, actual sensor circuit, diagnostic channel definition and current vehicle-specific procedure before changing a calibration.

SSP 203 describes a knock sensor with cylinder-selective correction and a separate fallback if its signal is lost. It states that the weak-signal self-diagnostic check runs only under specified coolant temperature, speed and load conditions; this is a diagnostic enable condition, not a recommended test point or a safe tuning limit. No fault code in a log taken outside the check’s conditions does not demonstrate that knock sensing is effective. Investigate mounting, wiring, fuel and faults using the applicable current procedure. VW SSP 203, sensors.

Calibration and file handling

Establish a healthy baseline before tuning: record fuel, engine and ECU identification, fault codes, intake and ignition condition and the source of the read. Where the chosen tool supports defined channels, compare engine speed, throttle, manifold pressure, intake and coolant temperature, lambda and ignition behaviour at repeatable conditions. Investigate an implausible pressure, temperature or correction as a measurement or hardware problem before interpreting it as a map issue.

These factory sources describe system operation, not a software-specific performance map pack, axes, addresses or tuning values. Do not assume Simos 2, 2.1 or 3 definitions are interchangeable. Confirm the actual read and write method, file format, checksum handling, memory scope and recovery support with the chosen tool provider. A supplied original or calibration-only read is not automatically the actual controller’s full recovery data.

Sources

Volkswagen SSP 203: 1.0-litre 37 kW petrol engine with camshaft in block, especially pages 4, 10, 15–17 and 20. AHT identification, load sensing, injection, knock control and diagnostic context. Training material, not a current workshop manual. Accessed 17 November 2026. Volkswagen SSP 201: The Lupo, engine data. Siemens Simos 2P AHT application example. Accessed 17 November 2026. SEAT technical training booklet 58: 1.0L Simos engine, French edition. Related Simos 2P system and paired-injection description; verify the actual engine and variant. Accessed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Simos 2P

Simos 2P is a Siemens petrol engine-management system documented by Volkswagen on the 1.0-litre AHT engine. It is a separate identification from the AEH and AKL Simos 2 examples in the Simos 2 overview. Identify the exact ECU, hardware and software before selecting a file, editor definition or programming method.

Documented application and identification

Volkswagen’s Self-Study Programme 203 identifies the Lupo 1.0 AHT as a 997 cm³ four-cylinder engine with Simos 2P multipoint injection. Its example is rated 37 kW at 5,000 rpm and 84 Nm at 3,250 rpm. These are factory figures for that engine, not calibration targets or proof that a particular vehicle retains its original ECU. Record the diagnostic identification, controller label, engine code and actual software.

The programme specifies 95 RON petrol for its example and says 91 RON can alternatively be used with reduced output through knock control. Follow the actual vehicle’s current fuel specification; this statement does not establish the fuel requirements of a modified calibration. Volkswagen’s Lupo SSP 201 independently identifies the AHT engine-management system as Siemens Simos 2P.

Load sensing and injection

For AHT, SSP 203 describes engine speed and intake-manifold pressure as inputs to the load calculation, with manifold air temperature also used to calculate intake air quantity. It describes the ECU calculating injection duration and ignition timing with corrections including lambda, idle and cylinder-selective knock control. These descriptions do not identify individual performance-map addresses or prove the same strategy for every Simos 2P calibration.

The documented engine has an injector upstream of each intake valve. Volkswagen describes semi-sequential paired operation: cylinders 1 and 4 are activated together, as are 2 and 3. This is port injection, not two direct-injection pulses. A shared pair command or a single lambda reading cannot establish that both injectors in that pair deliver equally; diagnose individual circuits and fuel delivery using the current workshop procedure. VW SSP 203, injection system.

Sensor fallback and knock diagnosis

In the same AHT example, manifold-pressure sender G71 and intake-air-temperature sender G42 are mounted at the intake manifold. Volkswagen says that with missing pressure signals the ECU uses throttle-position and engine-speed information with an emergency running map; if intake-air temperature is missing it uses a substitute of 45 °C. A plausible displayed value can therefore be a substitute rather than a live measurement. Check the fault memory, actual sensor circuit, diagnostic channel definition and current vehicle-specific procedure before changing a calibration.

SSP 203 describes a knock sensor with cylinder-selective correction and a separate fallback if its signal is lost. It states that the weak-signal self-diagnostic check runs only under specified coolant temperature, speed and load conditions; this is a diagnostic enable condition, not a recommended test point or a safe tuning limit. No fault code in a log taken outside the check’s conditions does not demonstrate that knock sensing is effective. Investigate mounting, wiring, fuel and faults using the applicable current procedure. VW SSP 203, sensors.

Calibration and file handling

Establish a healthy baseline before tuning: record fuel, engine and ECU identification, fault codes, intake and ignition condition and the source of the read. Where the chosen tool supports defined channels, compare engine speed, throttle, manifold pressure, intake and coolant temperature, lambda and ignition behaviour at repeatable conditions. Investigate an implausible pressure, temperature or correction as a measurement or hardware problem before interpreting it as a map issue.

These factory sources describe system operation, not a software-specific performance map pack, axes, addresses or tuning values. Do not assume Simos 2, 2.1 or 3 definitions are interchangeable. Confirm the actual read and write method, file format, checksum handling, memory scope and recovery support with the chosen tool provider. A supplied original or calibration-only read is not automatically the actual controller’s full recovery data.

Sources

Revision 1: Simos 2P

Simos 2P is a Siemens petrol engine-management system documented by Volkswagen on the 1.0-litre AHT engine. It is a separate identification from the AEH and AKL Simos 2 examples in the Simos 2 overview. Identify the exact ECU, hardware and software before selecting a file, editor definition or programming method.

Documented application and identification

Volkswagen’s Self-Study Programme 203 identifies the Lupo 1.0 AHT as a 997 cm³ four-cylinder engine with Simos 2P multipoint injection. Its example is rated 37 kW at 5,000 rpm and 84 Nm at 3,250 rpm. These are factory figures for that engine, not calibration targets or proof that a particular vehicle retains its original ECU. Record the diagnostic identification, controller label, engine code and actual software.

The programme specifies 95 RON petrol for its example and says 91 RON can alternatively be used with reduced output through knock control. Follow the actual vehicle’s current fuel specification; this statement does not establish the fuel requirements of a modified calibration. Volkswagen’s Lupo SSP 201 independently identifies the AHT engine-management system as Siemens Simos 2P.

Load sensing and injection

For AHT, SSP 203 describes engine speed and intake-manifold pressure as inputs to the load calculation, with manifold air temperature also used to calculate intake air quantity. It describes the ECU calculating injection duration and ignition timing with corrections including lambda, idle and cylinder-selective knock control. These descriptions do not identify individual performance-map addresses or prove the same strategy for every Simos 2P calibration.

The documented engine has an injector upstream of each intake valve. Volkswagen describes semi-sequential paired operation: cylinders 1 and 4 are activated together, as are 2 and 3. This is port injection, not two direct-injection pulses. A shared pair command or a single lambda reading cannot establish that both injectors in that pair deliver equally; diagnose individual circuits and fuel delivery using the current workshop procedure. VW SSP 203, injection system.

Sensor fallback and knock diagnosis

In the same AHT example, manifold-pressure sender G71 and intake-air-temperature sender G42 are mounted at the intake manifold. Volkswagen says that with missing pressure signals the ECU uses throttle-position and engine-speed information with an emergency running map; if intake-air temperature is missing it uses a substitute of 45 °C. A plausible displayed value can therefore be a substitute rather than a live measurement. Check the fault memory, actual sensor circuit, diagnostic channel definition and current vehicle-specific procedure before changing a calibration.

SSP 203 describes a knock sensor with cylinder-selective correction and a separate fallback if its signal is lost. It states that the weak-signal self-diagnostic check runs only under specified coolant temperature, speed and load conditions; this is a diagnostic enable condition, not a recommended test point or a safe tuning limit. No fault code in a log taken outside the check’s conditions does not demonstrate that knock sensing is effective. Investigate mounting, wiring, fuel and faults using the applicable current procedure. VW SSP 203, sensors.

Calibration and file handling

Establish a healthy baseline before tuning: record fuel, engine and ECU identification, fault codes, intake and ignition condition and the source of the read. Where the chosen tool supports defined channels, compare engine speed, throttle, manifold pressure, intake and coolant temperature, lambda and ignition behaviour at repeatable conditions. Investigate an implausible pressure, temperature or correction as a measurement or hardware problem before interpreting it as a map issue.

These factory sources describe system operation, not a software-specific performance map pack, axes, addresses or tuning values. Do not assume Simos 2, 2.1 or 3 definitions are interchangeable. Confirm the actual read and write method, file format, checksum handling, memory scope and recovery support with the chosen tool provider. A supplied original or calibration-only read is not automatically the actual controller’s full recovery data.

Sources