Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 16
Applies to
Simos 16
Tool groups
None
Manufacturers
None

Some supercharged Audi 3.0 TFSI engines with Simos 16 use both direct injection and manifold injection. Audi's Q7 245 kW technical sheet identifies that combination with Simos 16, while Audi SSP 624 describes the related EA837 evo CREA engine and calls its ECU Simos without a generation suffix. The CREA details below are a system example, not proof that every engine or market has an identical Simos 16 calibration.

Two injector systems and two pressure sides

In the CREA training example, the low-pressure supply feeds the manifold-injection rails and the high-pressure pump. A connection through the high-pressure pump maintains fuel flow through the pump even when the engine is using MPI. G410 measures low-side fuel pressure and G247 measures high-side rail pressure. The cam-driven high-pressure pump has metering valve N290 and supplies the direct-injection rails and one direct injector per cylinder. The MPI injectors deliver fuel into the intake-manifold flange. Confirm actual hardware, sensor and rail layout in the applicable workshop information before diagnosis.

SSP 624 illustrates roughly 4–5 bar low-side and a 100–200 bar mapped high-pressure operating range for that engine. These are descriptive figures, not universal acceptance limits or targets for a modified car. Compare actual and requested pressure at the same operating point using the current service procedure; verify the units and channel definitions. High-side pressure tracking alone cannot establish that the MPI rail, injector delivery, or air-fuel mixture is correct.

Injection-mode changes matter

Audi describes a flexible split between MPI and FSI on the CREA example. Its training diagram includes MPI-only and combined MPI with one, two or three FSI events; the allocation is variable. The text describes MPI use at idle and through much of the lower and medium load range, with the MPI portion reduced approaching full load. Actual transitions depend on calibration and operating conditions; neither an engine code nor one idle log establishes the exact split throughout the map.

If a hesitation or mixture deviation appears at a transition, compare available injection-mode and pulse information, engine speed, torque/load, throttle, lambda target and measured lambda for both banks, pressure targets and actuals, temperature, misfires and knock correction. Channel availability, scaling, whether a value is measured or calculated, and pulse-time units depend on the ECU and logger. A transition in mode is a useful time marker, not proof that the changeover caused the fault. Different sample rates and sensor delays can also make signals appear misaligned.

A separate CREC cold-start example

Audi TSB 01 20 46, 2014753/10, issued in 2020, describes a possible fuel-quality-related injector deposit condition in model-year 2016–2019 3.0 TFSI evo CREC vehicles. Audi says deposits may prevent an injector closing completely and that fuel entering the intake manifold or cylinder after shutdown can make the next start rich. In that bulletin Audi directs the specified additive procedure first when deposits are suspected, followed by further diagnosis if the concern remains. This is one historical, market-specific service example, not proof that any individual injector leaks, that a rich start has this cause, or that replacement is never appropriate. Check current applicable service information and revisions for the actual vehicle.

Hot-condition low-pressure fault: a separate Audi service example

Audi of America bulletin 20 17 96, 2043758/8 describes a low-pressure fuel fault and starting difficulty in specified 2012–2018 A6/A7 and other listed vehicles with 2.0 or 3.0 engines. Audi says the concern usually occurs in very hot ambient conditions after stop-start driving with extended idle and a hot engine, and identifies vapour in the fuel system as the technical background. For its 3.0 TFSI example the bulletin identifies P310B with symptom code 6183; it separately lists P125B00 with symptom code 16903. The bulletin does not establish the ECU variant or engine code of every listed vehicle, so it is a related service example rather than proof of a Simos 16-specific fault.

Audi directs technicians to check low-side pressure, delivery rate and fuel lines against the applicable workshop specifications, with a repair-kit procedure limited to the stated fault and symptom codes. It calls for normal diagnosis if P310B has a different symptom code. A low-pressure deviation or a hot-start complaint alone does not prove fuel vapour or identify a failed pump. Preserve freeze-frame and ambient, fuel and operating-condition data; compare the actual vehicle’s measured pressure and delivery with current workshop tests before deciding whether this historical bulletin applies. Do not treat its temperature context as a general fault threshold or its repair kit as a universal remedy.

Before changing the calibration

  1. Record the engine code, ECU identification, fuel, injector and pump hardware, calibration and a complete fault scan with freeze-frame information. Verify which injection systems and diagnostic channels are actually fitted.
  2. Capture a repeatable baseline where supported: low- and high-side pressure target and actual, both bank lambda targets and feedback, trims, injector operation or mode, speed, load, throttle and temperatures. Note whether the concern occurs during warm-up, a load transition or sustained operation.
  3. Investigate fuel supply, pressure control, sensors, injector operation, ignition and air leaks according to current vehicle-specific diagnosis. One bank's correction is a lead, not a component verdict; a high-pressure error alone does not diagnose the low-pressure side.
  4. After any repair or hardware change, repeat the same comparison. Do not transfer the illustrative CREA pressure range or another software's injection maps as tuning setpoints. Retain mixture and component protections and verify the calibration for the exact fuel and hardware.

Fuel injection equipment can remain pressurised. Follow the applicable manufacturer's depressurisation and repair procedure before opening either fuel circuit.

Sources