Simos 19.2 is a Continental petrol engine-management variant listed for certain 2.0 TFSI hybrid applications. Identify the controller and software on the actual vehicle before applying a definition or programming procedure; the Simos 19 family also contains different engine and vehicle platforms.
Factory-documented hybrid example
Audi Self-Study Programme 686, pages 24–26, identifies Simos 19.2 on its EA888 generation 3, 2.0-litre DLGA plug-in hybrid example. It names the Q5 50 TFSI e (type FY), A6 50 TFSI e (type 4A) and A7 50 TFSI e (type 4K) in this drive concept. For the published example Audi states 185 kW combustion-engine output, 105 kW peak electric-motor output and 220 kW combined system output. The stated combined output is not obtained by simply adding the two peak ratings. These are factory training examples at publication, not a complete fitment list or a calibration target. Identify the ECU and software on the vehicle.
SSP 686 describes the electric motor in the 0DK dual-clutch transmission on this drive concept. Its discussion of electric-motor boost for MLB TFSI e models depends on operating conditions including driving mode, battery charge and temperature; here “boost” means electric assistance, not turbocharger pressure. Record these conditions when comparing hybrid performance runs. The training programme cautions that later model years and platforms may differ.
Documented catalogue examples
A Dimsport supported-vehicle list dated March 2025 names Simos 19.2 for examples including an Audi Q5 80A 2.0 TFSI hybrid and a Q5 55 TFSIe. The list is a product catalogue, not a complete manufacturer fitment record. The listed power of a hybrid vehicle must not automatically be treated as the combustion engine’s standalone output or a tuning target. Verify the vehicle’s actual engine, gearbox, hybrid equipment and diagnostic ECU identification.
simos.app’s SCM7C1 definition page identifies SCM7C1 as Simos 19.2 and lists boxcode 80A906259B without a software version. The provider says known combinations are derived from BIN filenames and that the software identifier must be verified in the loaded file. The entry is a tool-specific compatibility lead; it does not prove a particular vehicle or software version, validate all indexed parameters, or establish flashing support. Match the exact controller, calibration, file and editor definition before use.
Read, edit and write are distinct
bFlash’s V2610C release of 29 October 2026 lists Simos 19.2, 19.7 and 19.8 in a beta OBD virtual-read protocol for specified MLB Evo 2.0 TSI/TFSI mild-hybrid and plug-in-hybrid applications. Its vehicle list is grouped across all three variants. The provider says full flash is available on request; it does not establish physical full-read or EEPROM coverage for every ECU. Confirm the exact hardware, software, licensing, tool version and read, write and recovery operations with the provider.
A virtual read is a supplied matching file, not necessarily a physical copy of the ECU’s current modifications. Record its provenance and the original diagnostic identity, verify the file and checksum handling, and establish what the tool can restore. Editing a BIN in one product is not evidence that the same product can flash it. Do not assume that a map-only read includes EEPROM or all vehicle-specific data.
Calibration and log review
Establish a healthy baseline and record fuel, hardware changes, ECU and transmission software, hybrid state and fault codes. Use supported, correctly defined channels to compare engine torque requests and limits, charge-pressure target and actual, lambda, fuel pressure, ignition corrections and temperatures under repeatable conditions. Hybrid operating mode, battery state and electric-machine contribution affect the interpretation of vehicle output; an engine ECU torque channel alone is not a measurement of total system or wheel output.
No source here supplies validated 19.2 map addresses, universal scaling or safe tuning values. Do not copy map definitions or feature settings from the separately documented transverse EA888 Evo4 applications merely because the ECU family number is similar. Preserve the original file and make a change record with the relevant logs and independently measured results.
Sources
- Audi SSP 686: TFSI e models, pages 24–26 and 101, reproduced text. DLGA Simos 19.2 example, hybrid output and electric assistance. Training reference, not a current workshop manual. Accessed 17 November 2026.
- Dimsport supported-vehicle list, 11 March 2025, as hosted by Tuning-shop. Product-specific Q5 80A hybrid listings; not exhaustive fitment proof. Accessed 17 November 2026.
- simos.app SCM7C1 Simos 19.2 definition. Identifier, boxcode and stated limitations of filename-derived matches. Accessed 17 November 2026.
- bFlash V2610C Simos 19.2/19.7/19.8 release, 29 October 2026. Product-specific beta coverage. Accessed 17 November 2026.