The supercharger clutch adds an operating state to some EA837 evo 3.0 TFSI installations associated with Simos 16. A low boost reading or a clutch that is not engaged at light load does not by itself identify a fault. Check the actual engine, ECU, supercharger and calibration before applying the following examples.
Documented scope
Audi's Q7 3.0 TFSI technical sheet identifies Simos 16 and a deactivatable supercharger for the 245 kW vehicle described. Audi SSP 624 describes a fourth-generation EA837 evo system using a CREA example and calls its ECU “Simos” without specifying the ECU generation. Its clutch operation below is engine-system context; it does not establish identical behaviour on every Simos 16 vehicle. Inspect the installed hardware and use the current repair information for the specific vehicle.
What changes during engagement
On the SSP 624 example, electromagnetic clutch N421 connects or disconnects the drive to the Roots rotors. At certain low loads and speeds the clutch is open; airflow through the rotors still causes them to rotate slowly. An open clutch at idle or part load is therefore not proof of a failed clutch. Audi identifies engine speed and driver torque demand among the inputs to the operating strategy; other conditions also affect it.
Audi describes current-controlled clutch engagement coordinated with the throttle and recirculation flap. The ECU uses rotor-speed feedback from the Hall-effect sensor G688 to calculate engagement or disengagement timing and monitor clutch operation. Its formal diagnostic name refers to a turbocharger, but in this documented engine it measures supercharger rotor speed. When the signal is lost, SSP 624 says controlled transition is unavailable and switching can become harsh. A harsh transition alone does not prove that sensor G688 is at fault.
Clutch protection and pulley changes
Audi describes a calculated clutch stress factor using speed difference and acceleration time. It says this example has no dedicated clutch-temperature sensor. If the factor passes a threshold, the strategy can prevent disengagement for a period to allow heat to dissipate. Therefore clutch state after repeated transitions can reflect an intentional protection strategy; neither a fixed delay nor a displayed state proves component temperature.
The programme describes a plausibility comparison between supercharger speed and crankshaft speed for the documented system. Pulley changes affect the physical relationship between those speeds; do not assume a stock ratio, scaling or diagnostic limit is valid after a hardware change. Confirm the installed pulleys, software and relevant supplier documentation. This observation does not justify disabling monitoring or changing clutch limits to hide a mismatch.
Pulley ratio: a product-specific example
APR’s 3.0 TFSI pulley description gives an approximately 63.25 mm original supercharger drive pulley and a 57.75 mm replacement, and says this change spins the supercharger about 9.5% faster. For its crank pulley it states approximately 162 mm original and 187 mm replacement, or about 15.4% faster. These are APR’s nominal measurements and claims for its products, not verified sizes for every EA837 installation. Its description says its Gen 2 Simos 16 crank-pulley offering is used in a dual-pulley configuration. APR’s separate EA837 evo software page describes specific calibration stages for single- and dual-pulley configurations; check current compatibility for the actual boxcode, fuel and parts.
For illustration only, when the clutch is engaged and the rest of the drive ratio is unchanged, the speed ratio between two configurations is approximately (new crank diameter / old crank diameter) × (old supercharger diameter / new supercharger diameter), neglecting slip and measurement differences. Using APR’s rounded figures for both changes gives (187 / 162) × (63.25 / 57.75), approximately 1.264: about 26% more rotor speed at the same crankshaft speed. The percentages multiply, rather than simply add. This is a calculated comparison using the stated nominal sizes, not a measured speed, a supercharger speed limit or proof of safe operation at any engine speed.
As a diagnostic check, compare correctly defined, time-aligned G688 rotor-speed and engine-speed channels in stable engaged operation before and after the hardware change. The estimated ratio cannot diagnose clutch slip from a single transient, validate a sensor scale or tell whether the ECU’s plausibility limits remain appropriate. When the clutch is open, the directly driven pulley-ratio comparison does not describe rotor speed. Check belt condition, the actual dimensions, engine and clutch state, supplier calibration requirements and fault memory alongside pressure and temperature data. Preserve applicable protections and use suitable independent measurements when validating the result.
Log review and fault diagnosis
- Record ECU and calibration identifiers, engine and gearbox, fuel, drive mode, pulley sizes, other modifications, fault codes and the operating conditions before clearing codes or changing the file.
- Where supported and correctly defined, compare engine speed and driver demand with clutch requested state or current, supercharger rotor speed, throttle and bypass position, and pressure target and actual. Confirm the channels' units, update rate and whether each is requested, measured or modelled. An indicated clutch command does not independently prove the clutch transmitted torque.
- Correlate engagement timing with misfire, knock correction, ignition, lambda, fuel pressure and charge temperatures. Investigate wiring, supply, mechanical drive, air leaks, sensor faults and cooling using the exact repair procedure. Test a calibration change only after the mechanical baseline and diagnostic evidence are understood.
- Compare similar operating conditions before and after a repair or calibration change. A clutch-related code or poor acceleration can have more than one cause; do not diagnose or replace a component from a generic log label alone.
Q7 service bulletin example
Audi of America's TSB 2048402/9, dated November 2021, covers certain 2017–2019 Q7 3.0 TFSI evo cases with MIL and either P25EA00, “supercharger disconnect clutch stuck closed”, or P05A000, an active grille shutter fault. It describes a vehicle-specific ECM software action where necessary and tells technicians not to replace parts unless directed. The additional radiator-shutter checks in that bulletin apply to P05A000 only; they are not a supercharger-clutch repair procedure. The bulletin does not prove that every P25EA00 has the same cause or that the described software action is current for another vehicle.
The bulletin's table identifies a CREC Q7 software example. Confirm applicability, supersession, ECU identification and the latest guided procedure with the vehicle manufacturer's service system. A factory software change can alter the original calibration or its identifiers: record the version before and after authorised repair and confirm compatibility of any tune and definition with their suppliers.
Sources
- Audi Q7 3.0 TFSI quattro 245 kW technical data, Germany, December 2014. Identifies Simos 16 and a deactivatable supercharger on the specified vehicle. Accessed 17 November 2026.
- Audi Self-Study Programme 624: fourth-generation EA837 evo, English rendering, pages 22–27. N421 clutch, control transitions, G688 and calculated stress-factor protection; describes Simos without identifying the generation. Accessed 17 November 2026.
- Audi of America TSB 2048402/9: MIL with P05A000 or P25EA00, 22 November 2021. Specific 2017–2019 Q7 3.0 TFSI evo service case; consult current repair information. Accessed 17 November 2026.