Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Simos 2 is a Siemens petrol engine-management family documented on naturally aspirated Volkswagen Group engines. Škoda and Audi training material identifies Simos 2 on the 1.6-litre AEH; a Škoda workshop manual also lists the 1.6 AKL with Simos 2. The precise ECU suffix and software must be identified on the actual unit before selecting a definition or programming method.

Documented examples and identification

Škoda SSP 15 describes the 1.6 AEH with Simos 2, a hot-film air-mass meter and a variable intake manifold in the Octavia. A Škoda Octavia workshop-manual copy lists AEH and AKL as 1,595 cm³, 74 kW naturally aspirated engines with Simos 2. It is a table for those applications, not a complete fitment catalogue or proof of an individual ECU suffix.

VW SSP 191 separately lists Simos 2 on the Passat 1.6 AHL and says that Passat installation has no twin-path intake manifold. Do not assume the Octavia manifold hardware is present because a car has a Simos 2 ECU. Audi SSP 182 also names Simos 2 for its A3 AEH example. These sources identify the family without allocating a suffix to every example.

A Snap-on diagnostic application guide lists selected SEAT Ibiza 1.6 AEH and AKL examples under Simos 2.1; this is the tool supplier's application coverage, not a universal fitment or flashing statement. Record the ECU label, full part and software numbers, engine code and gearbox, then match them to the selected tool's current documentation. A petrol Simos 2.1 is distinct from the later diesel PCR 2.1 label.

A separately reproduced SEAT injection-system technical-data table explicitly pairs AEH and AKL with Simos 2.1, while its APF and AUR column names Simos 3.3. It is a scoped workshop table, not proof of the controller in every vehicle with those engine codes. Its technical figures and service procedures are for the listed installations; identify the ECU before deciding which column and diagnostic procedure apply.

AEH air and engine control

For its AEH example, Audi SSP 182 lists hot-film air-mass meter G70, engine-speed sender G28, Hall sender G40, lambda sensor G39, knock sensor G61, coolant and intake-air temperature sensors and throttle-control unit J338. It shows four injection valves and two ignition coils. The throttle assembly in that system includes a throttle potentiometer, a positioner potentiometer and an idle switch; verify the actual hardware before applying details to another ECU or vehicle.

On the variable-manifold AEH described by Škoda SSP 19, the ECU operates N156 in response to load and engine speed and uses vacuum to change intake runner length. The long path supports lower-speed torque and the short path the higher-speed range. The programme describes the short path as the fallback when the valve signal is absent. It also describes a separate high-speed changeover used for soft speed limiting in that example: these are factory strategy descriptions, not generic switch points or an instruction to raise a limiter.

Diagnosis and tuning baseline

  1. Record the exact controller and software, fuel, faults, modifications and the complaint. Investigate ignition misfires, intake leaks, air-meter and coolant-temperature plausibility, fuel delivery and lambda operation before changing calibration.
  2. Where supported, compare engine speed, throttle, air mass, lambda, fuel corrections and ignition or knock-related values under repeatable conditions. Confirm units, availability and sample rate for the specific diagnostic tool; a displayed air or torque value may be calculated rather than independently measured.
  3. If the documented variable-manifold engine has a power complaint, the Škoda Octavia workshop procedure checks changeover operation, N156, vacuum lines and linkage. A failed changeover has several possible electrical, vacuum and mechanical causes; follow the current procedure for the actual installation.
  4. Confirm that any calibration definition matches the exact file and that axes, units and functions have been validated. The cited factory descriptions do not provide universal map addresses, performance gains or safe timing changes. A plausible map name is not proof that it controls the intended function.

Reading and writing

Diagnostic access, reading the calibration, reading all relevant memory and writing a modified file are separate capabilities. The diagnostic supplier's 2.1 vehicle listing does not establish any particular flashing protocol. Check the tool provider's exact ECU and software coverage, memory scope, checksum handling, power supply and recovery procedure before writing; retain a restorable original in the appropriate format. A purchased or supplied original is not automatically the vehicle's current calibration or a complete backup.

For a programming-tool example, the ECU Tools CombiLoader listing includes Siemens SIMOS 2.x in its base software's ST10F27x/C16x bootstrap-loader coverage. The listing does not identify all supported ECU part and software numbers or specify which memory regions are accessible for each 2.x controller. This is a product-specific claim, not proof of OBD read/write support or that its output contains all ECU and immobiliser data. Confirm the exact unit, connection, read/write operation and recovery coverage with the provider and record the memory area and provenance of every read.

Sources