Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Simos 7.2 is a Volkswagen Group petrol engine-management designation documented by Volkswagen on a 2006 Passat 1.6-litre BSE example. The engine code does not uniquely identify the ECU: other Volkswagen training material names Simos 7.1 and Simos 7PP on different BSE applications. Read the controller and software identification before choosing a calibration or programming operation.

Documented Passat example

Volkswagen Self-Study Programme 339, page 26, lists the naturally aspirated 1,595 cm³ BSE four-cylinder with Simos 7.2, 75 kW at 5,600 rpm and 148 Nm at 3,800 rpm. It describes a plastic variable intake manifold, pressure-sensor-based air system, secondary air, and no exhaust-gas recirculation on that example. Its listed reference fuel is 95 RON unleaded, with 91 RON permitted with reduced performance. These are manufacturer details for the stated vehicle, not a guarantee for every BSE or a modified calibration.

The same engine code appears with 7.1 in VW's Jetta SSP 354 and 7PP in Golf SSP 423. Different application documents therefore cannot identify the installed controller from engine code alone. Record the ECU label, diagnostic part and hardware numbers, full software or calibration identifier, transmission and market. The training texts do not provide a 7.2 tuning map definition or prove interchanging files across controllers is possible.

Air, mixture and an investigation baseline

The documented BSE example uses a manifold-pressure-based system rather than the hot-film air-mass-meter arrangement mentioned for its predecessor. It has a variable intake manifold and distinct upstream linear and downstream switching oxygen sensors. A scanner's air-mass value may be calculated; check the connected vehicle's sensor and channel definitions before identifying it as a physical air-mass sensor. Pressure, estimated cylinder charge and actual airflow are related but not interchangeable. VW SSP 339.

Before evaluating changes, record the fuel, ECU version, equipment, diagnostic trouble codes and baseline condition. Where supported and correctly defined, review speed, pedal, throttle, manifold pressure and inlet temperature, intake-manifold changeover, lambda and trims, ignition timing, knock correction and coolant temperature under comparable operating conditions. Investigate air leaks, mixture, ignition and manifold changeover faults first. A demand or estimated torque change alone is not proof of measured output, and a plausible pressure value does not prove the intake changeover works mechanically.

Identification and programming evidence

IVA-Soft's Simos 7.X catalogue labels 5WP40377 / 06A906033EF / CAS72027 / 1045 as a BSE 7.2 example and gives 06A906033AT / CAS72018 with calibration identifiers 8172 and 9600. These are catalogue claims, not independently verified files or an interchangeability list; the presence of the same number with different calibration identifiers illustrates why the complete identification matters. The catalogue calls these entries “full flash” but does not prove that an available file includes EEPROM or vehicle-specific data.

A rehosted PCM service-help page, reviewed through indexed text because direct access failed, names 7.2 together with 7.1 and 7PP, while the PCMflash manual lists separate BSA/BSE/BSF calibration operations for 7.1 and 7PP without explicitly naming 7.2 in that list. These are product-specific descriptions; they do not establish current 7.2 compatibility or a safe protocol choice for a particular unit. Confirm with the selected tool provider which exact ECU, read/write operation, connection, checksums and recovery procedure are supported. A calibration-area read is not automatically a complete ECU backup.

No verified 7.2 addresses, axes, numerical ignition settings or fuel maps are established by these sources. Match and validate the exact definition and software, preserve the original data and test changes with suitable measurements rather than copying a 7.1 or 7PP map by name.

Sources

Volkswagen SSP 339: The Passat 2006, page 26. BSE, Simos 7.2 and documented engine equipment. Accessed 17 November 2026. Volkswagen SSP 354: The Jetta 2006 and SSP 423: Golf 2009. Separately documented BSE 7.1 and 7PP examples. Accessed 17 November 2026. IVA-Soft Simos 7.X software catalogue. Third-party identification and file-scope claims, not independent verification. Accessed 17 November 2026. PCM service-help rendering and PCMflash manual, module 17. Product-specific and differing description scope; verify current 7.2 operation with the provider. Accessed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Simos 7.2

Simos 7.2 is a Volkswagen Group petrol engine-management designation documented by Volkswagen on a 2006 Passat 1.6-litre BSE example. The engine code does not uniquely identify the ECU: other Volkswagen training material names Simos 7.1 and Simos 7PP on different BSE applications. Read the controller and software identification before choosing a calibration or programming operation.

Documented Passat example

Volkswagen Self-Study Programme 339, page 26, lists the naturally aspirated 1,595 cm³ BSE four-cylinder with Simos 7.2, 75 kW at 5,600 rpm and 148 Nm at 3,800 rpm. It describes a plastic variable intake manifold, pressure-sensor-based air system, secondary air, and no exhaust-gas recirculation on that example. Its listed reference fuel is 95 RON unleaded, with 91 RON permitted with reduced performance. These are manufacturer details for the stated vehicle, not a guarantee for every BSE or a modified calibration.

The same engine code appears with 7.1 in VW's Jetta SSP 354 and 7PP in Golf SSP 423. Different application documents therefore cannot identify the installed controller from engine code alone. Record the ECU label, diagnostic part and hardware numbers, full software or calibration identifier, transmission and market. The training texts do not provide a 7.2 tuning map definition or prove interchanging files across controllers is possible.

Air, mixture and an investigation baseline

The documented BSE example uses a manifold-pressure-based system rather than the hot-film air-mass-meter arrangement mentioned for its predecessor. It has a variable intake manifold and distinct upstream linear and downstream switching oxygen sensors. A scanner's air-mass value may be calculated; check the connected vehicle's sensor and channel definitions before identifying it as a physical air-mass sensor. Pressure, estimated cylinder charge and actual airflow are related but not interchangeable. VW SSP 339.

Before evaluating changes, record the fuel, ECU version, equipment, diagnostic trouble codes and baseline condition. Where supported and correctly defined, review speed, pedal, throttle, manifold pressure and inlet temperature, intake-manifold changeover, lambda and trims, ignition timing, knock correction and coolant temperature under comparable operating conditions. Investigate air leaks, mixture, ignition and manifold changeover faults first. A demand or estimated torque change alone is not proof of measured output, and a plausible pressure value does not prove the intake changeover works mechanically.

Identification and programming evidence

IVA-Soft's Simos 7.X catalogue labels 5WP40377 / 06A906033EF / CAS72027 / 1045 as a BSE 7.2 example and gives 06A906033AT / CAS72018 with calibration identifiers 8172 and 9600. These are catalogue claims, not independently verified files or an interchangeability list; the presence of the same number with different calibration identifiers illustrates why the complete identification matters. The catalogue calls these entries “full flash” but does not prove that an available file includes EEPROM or vehicle-specific data.

A rehosted PCM service-help page, reviewed through indexed text because direct access failed, names 7.2 together with 7.1 and 7PP, while the PCMflash manual lists separate BSA/BSE/BSF calibration operations for 7.1 and 7PP without explicitly naming 7.2 in that list. These are product-specific descriptions; they do not establish current 7.2 compatibility or a safe protocol choice for a particular unit. Confirm with the selected tool provider which exact ECU, read/write operation, connection, checksums and recovery procedure are supported. A calibration-area read is not automatically a complete ECU backup.

No verified 7.2 addresses, axes, numerical ignition settings or fuel maps are established by these sources. Match and validate the exact definition and software, preserve the original data and test changes with suitable measurements rather than copying a 7.1 or 7PP map by name.

Sources

Revision 1: Simos 7.2

Simos 7.2 is a Volkswagen Group petrol engine-management designation documented by Volkswagen on a 2006 Passat 1.6-litre BSE example. The engine code does not uniquely identify the ECU: other Volkswagen training material names Simos 7.1 and Simos 7PP on different BSE applications. Read the controller and software identification before choosing a calibration or programming operation.

Documented Passat example

Volkswagen Self-Study Programme 339, page 26, lists the naturally aspirated 1,595 cm³ BSE four-cylinder with Simos 7.2, 75 kW at 5,600 rpm and 148 Nm at 3,800 rpm. It describes a plastic variable intake manifold, pressure-sensor-based air system, secondary air, and no exhaust-gas recirculation on that example. Its listed reference fuel is 95 RON unleaded, with 91 RON permitted with reduced performance. These are manufacturer details for the stated vehicle, not a guarantee for every BSE or a modified calibration.

The same engine code appears with 7.1 in VW's Jetta SSP 354 and 7PP in Golf SSP 423. Different application documents therefore cannot identify the installed controller from engine code alone. Record the ECU label, diagnostic part and hardware numbers, full software or calibration identifier, transmission and market. The training texts do not provide a 7.2 tuning map definition or prove interchanging files across controllers is possible.

Air, mixture and an investigation baseline

The documented BSE example uses a manifold-pressure-based system rather than the hot-film air-mass-meter arrangement mentioned for its predecessor. It has a variable intake manifold and distinct upstream linear and downstream switching oxygen sensors. A scanner's air-mass value may be calculated; check the connected vehicle's sensor and channel definitions before identifying it as a physical air-mass sensor. Pressure, estimated cylinder charge and actual airflow are related but not interchangeable. VW SSP 339.

Before evaluating changes, record the fuel, ECU version, equipment, diagnostic trouble codes and baseline condition. Where supported and correctly defined, review speed, pedal, throttle, manifold pressure and inlet temperature, intake-manifold changeover, lambda and trims, ignition timing, knock correction and coolant temperature under comparable operating conditions. Investigate air leaks, mixture, ignition and manifold changeover faults first. A demand or estimated torque change alone is not proof of measured output, and a plausible pressure value does not prove the intake changeover works mechanically.

Identification and programming evidence

IVA-Soft's Simos 7.X catalogue labels 5WP40377 / 06A906033EF / CAS72027 / 1045 as a BSE 7.2 example and gives 06A906033AT / CAS72018 with calibration identifiers 8172 and 9600. These are catalogue claims, not independently verified files or an interchangeability list; the presence of the same number with different calibration identifiers illustrates why the complete identification matters. The catalogue calls these entries “full flash” but does not prove that an available file includes EEPROM or vehicle-specific data.

A rehosted PCM service-help page, reviewed through indexed text because direct access failed, names 7.2 together with 7.1 and 7PP, while the PCMflash manual lists separate BSA/BSE/BSF calibration operations for 7.1 and 7PP without explicitly naming 7.2 in that list. These are product-specific descriptions; they do not establish current 7.2 compatibility or a safe protocol choice for a particular unit. Confirm with the selected tool provider which exact ECU, read/write operation, connection, checksums and recovery procedure are supported. A calibration-area read is not automatically a complete ECU backup.

No verified 7.2 addresses, axes, numerical ignition settings or fuel maps are established by these sources. Match and validate the exact definition and software, preserve the original data and test changes with suitable measurements rather than copying a 7.1 or 7PP map by name.

Sources