Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 10
Applies to
Simos 10
Tool groups
None
Manufacturers
None

On the 1.2 TSI/TFSI CBZA and CBZB installations described in Audi's Self-Study Programme 485, Simos 10 controls turbo charge pressure using an electric wastegate actuator and pressure and temperature signals at more than one point in the air path. This page is scoped to that documented system. Identify the actual engine, ECU and hardware before applying the same component names to another Simos 10 installation.

Control path and measurement points

The ECU calculates a nominal charge-pressure request from torque demand and adjusts charge-pressure actuator V465 to move the turbocharger wastegate. Position sensor G581 supplies actuator-position feedback. Audi describes the actuator as integral to the turbocharger assembly, with a Hall-effect position sensor; its training text states that a replacement module must be programmed using the specified guided functions. The current repair procedure for the actual vehicle and part remains authoritative.

Audi's diagram locates charge-pressure sender G31 with intake-air-temperature sender G299 in the charge-pressure pipe, upstream of the throttle. It locates manifold-pressure sender G71 with temperature sender G42 downstream, in the intake manifold and charge-air-cooler path. An ambient-pressure sender in the ECU provides a correction. The G31 signal is used to control and monitor charge pressure; G71 and G42 contribute to the calculation of air mass in the manifold. High inlet temperature can lead to a reduction in charge pressure for component protection.

These are different physical locations. A pressure difference across a partly closed throttle, or during a transient, does not by itself prove that a sensor is defective. Identify each logger channel's sensor, units and absolute or gauge reference before comparing values. At ignition on with the engine stopped and the system settled, an atmospheric reference is a useful plausibility check for relevant pressure readings, but compare against the current workshop specification and actual ambient pressure rather than a fixed universal number.

Diagnosing a low or unstable result

  1. Record the conditions. Capture fault codes and freeze-frame information before clearing anything. Note ECU identification, engine, gearbox, fuel, software and calibration, turbocharger and actuator part numbers, recent repairs and the conditions in which the issue appears.
  2. Separate the request from the result. Where supported, log rpm, pedal and throttle position, requested and actual charge pressure, actuator command and reported position, upstream and manifold pressure, inlet and coolant temperatures, and intervention or fault status. A low actual pressure with a low requested pressure is a different starting point from a low actual pressure when the request remains high. The reason still needs diagnosis.
  3. Check the air and cooling systems. Use the vehicle-specific procedure to investigate leaks or restrictions, pressure-sensor and temperature-sensor readings, and charge-cooling circuit operation. On the SSP 485 example the charge cooler has a coolant circuit; poor cooling or a misleading temperature signal can change permitted pressure. Do not defeat the temperature protection to conceal a cooling fault.
  4. Check control and mechanical movement. Compare commanded and reported actuator position only where the diagnostic tool defines compatible units and conditions. Inspect applicable wiring, connections, actuator and linkage for faults using the current workshop test procedure. A plausible position signal does not independently prove that the valve seals correctly or that the air path is leak-free.
  5. Verify after repair. Follow the correct guided function and adaptation procedure where required, then repeat comparable observations and review codes and relevant fuel, lambda and ignition channels. Basic settings, limits, signal direction and test conditions must be taken from the current procedure for the installed unit; do not borrow numeric adjustment values from another engine or diesel actuator.

On the documented system the electric actuator replaces the pressure-cell and N75 arrangement described for Audi's comparison engine. A generic P-code procedure for a vacuum-operated diesel actuator is not automatically the correct test for this petrol engine. A diagnostic code is a starting point and does not establish one failed component.

SEAT's CBZB control and fallback example

SEAT's Self-Study Programme 136 describes the Simos 10 1.2 TSI 77 kW example using V465 electric wastegate control without a separate N75 boost-pressure control valve or N249 turbocharger recirculation valve. These component statements describe that installation, not every 1.2 TSI engine. Verify the actual turbo and air plumbing before using a generic N75 or N249 test or assuming that either component must be added for a replacement turbocharger.

For its documented 1.2 TSI system, SEAT states that if G581 feedback fails, V465 no longer regulates the wastegate and the wastegate remains mechanically open. It describes the same open-wastegate fallback for a V465 actuator fault, with no turbo overboost produced. An open position or low pressure alone does not establish whether the fault is electrical, sensor-related, mechanical or commanded; check the fault memory, current test plan and physical system. The training text is not evidence that every failure mode or every Simos 10 calibration behaves identically.

The same programme describes a charge-pressure calculation based on accelerator position and engine speed, corrected for inlet temperature, coolant temperature and altitude, and gives a maximum of 2.1 bar absolute for its example. That number includes atmospheric pressure, is not a boost-gauge reading or a target for a modified vehicle, and is not proof of what the connected sensor or ECU requests. Compare the actual pressure target, measured values and ambient pressure using the channel definitions for the specific car. SEAT SSP 136, pages 7 and 18–21.

Replacement turbochargers and software

BTS Turbo service information SI-201208 describes specific replacement turbo and service-kit numbers for CBZA, CBZB and CBZC engines. It states that changes in the electric actuator can require a vehicle-manufacturer software action and describes an actuator fault after ignition-on as a possible indication in that replacement context. This is a supplier bulletin for the parts it names, not evidence that every fault or replacement requires the same update. Match the turbocharger and ECU to current manufacturer guidance.

A factory software update can alter the identification and calibration on which an existing tune or definition depends. Record the version before and after the authorised repair; confirm the compatible file and tool with its supplier before making any further calibration change. Do not assume an earlier tune or actuator basic setting remains appropriate after a replacement or software update.

Sources