Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 10
Applies to
Simos 10
Tool groups
None
Manufacturers
Volkswagen

This guide uses Volkswagen's documented 1.2-litre, 77 kW CBZB engine with Simos 10 to explain direct-injection modes and fuel-pressure checks relevant to calibration work. The self-study programme does not specify a Simos 10 suffix or establish that every Simos 10 vehicle has the same components or calibration. Identify the actual engine, ECU and software first. VW SSP 443.

Pressure system and injector context

SSP 443's system diagram identifies low-pressure pump G6 and its controller J538, fuel pressure sender G247, fuel-pressure regulating valve N276 and direct injectors N30–N33. It illustrates a high-pressure pump supplying the rail and injectors. The programme describes six spray jets per injector and an injection pressure range of 40–125 bar for its 1.2 TSI example. That range describes the system in the training material; it is not a single desired pressure, a fault threshold or a permissible tuning target for every vehicle and operating point. Use the current workshop data for the identified engine. VW SSP 443, pages 13 and 22–24.

Pressure must be interpreted with demand, engine speed and injection timing: a satisfactory rail-pressure number alone does not prove that the injectors deliver the required quantity or that mixture is correct. Equally, a momentary difference between requested and actual pressure does not by itself identify a defective pump or prove a calibration problem. Confirm sensor and log units, sample timing and the applicable test conditions.

Two direct-injection events

VW describes two distinct uses of split injection for the CBZB. During catalyst heating the first injection takes place during intake and the smaller second event occurs before ignition top dead centre; the programme describes an 80% first-event share for that example. It also describes split injection from idle through full load up to 3,000 rpm: the first event occurs during the intake stroke and, depending on the calibration, accounts for 50–80% of fuel; the remaining fuel is injected at the start of compression. These are two pulses of direct injection, not evidence of separate port injectors. The training description does not establish exactly when every real-world calibration selects or leaves a mode. VW SSP 443, page 24.

When comparing runs, record warm-up state, coolant temperature, time after start, speed and load. A change in engine behaviour or exhaust sound during catalyst heating can reflect a different operating mode, but does not rule out a fault. A pulse-width or injection-angle channel must be understood in context: confirm whether it represents one event, a combined value or a calculated quantity before inferring total fuel delivery.

What the map listing does and does not establish

For a separate SEAT Ibiza file labelled Simos 10.22, Auto-Remap's 03F906070GR 5485 listing advertises injection base, correction and enrichment labels, two requested-lambda labels and two rail-pressure labels. The public page does not show sizes, axes or positions for those maps. The seller's labels do not identify which maps control either split-injection mode described above or verify their units, scaling or operating conditions. Match and validate the exact file and definition before drawing conclusions; SSP 443 names Simos 10 but does not identify this particular file or its suffix.

Reviewing logs and diagnosing a mismatch

  1. Record the engine code, ECU identifiers, fuel and hardware, current faults and relevant maintenance. Establish a healthy baseline before assessing an edited calibration.
  2. Where supported, log high-pressure target and actual, engine speed and load, lambda target and measured lambda, and the fuel metering or pressure-control command. Check whether channel values are measured or calculated and whether sampling rates can capture a transient. The public CBZB N276 diagnostic listing similarly groups requested and actual high pressure with a fuel-metering value, but its numerical test criteria are not publicly displayed.
  3. Compare matched conditions and look at the target as well as the result. If actual pressure persistently fails to follow a plausible request, investigate low-pressure supply, the control valve and electrical circuit, pressure sensor and high-pressure pump using the applicable workshop procedure. An apparent mismatch can also result from channel definition or sampling; do not replace parts based on one trace.
  4. Review commanded and measured lambda, injection events where reliably defined, and ignition corrections alongside fuel pressure. If pressure follows its request but mixture is unexpected, pressure alone does not explain the result; check sensor validity, air and fuel delivery, and test conditions. Preserve component protections and do not assume that raising rail pressure or copying injection splits will fix a lean condition.

The fuel rail can retain hazardous pressure. Follow the vehicle-specific workshop pressure-relief and repair procedure before opening the system; the log-review process above is not a substitute for it.

Sources

Sources accessed 17 November 2026.