Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 12
Applies to
Simos 12
Tool groups
None
Manufacturers
None

Simos 12.1 calibration work starts with the exact ECU software and a verified definition. This page uses a named 1.8 TFSI file as an example of how to inspect torque, load, boost and fuelling labels together. It does not establish a universal map layout, a required list of changes, or safe numerical settings for other files.

A specific file and a visible map example

Auto-Remap's commercial listing for 8V0906264B 0002 labels the file Simos 12.1 for an Audi A3 1.8. The seller advertises groups for calculated and requested torque, torque and clutch limits, requested load, turbo pressure, wastegate, rail pressure, lambda and spark. These are seller-provided names for the advertised file: they have not been independently checked against a factory definition or live execution.

The same listing shows one example labelled “Requested engine load”, described as a 12-by-16 table with torque in Nm on the horizontal axis, speed in rpm on the vertical axis, and values in mg/st. For instance, its shown cell at 200 Nm and 3,008 rpm is 554 mg/st. This illustrates how the seller says that one table is arranged; it is not a target to copy or proof of which map is active. The remaining map names are listed publicly, but their sizes, axes and positions are not all shown on the page. Confirm the read, map boundaries, axes, units and intended function in a definition matched to the actual calibration.

The seller separately lists 8V0906264B 0003 and advertises a different set and number of labels, including requested-load and spark groups. This difference is evidence of what the seller included in each pack; it does not prove the underlying ECUs contain exactly those counts, nor that maps with the same label are interchangeable. The seller describes the packs as CSV exports rather than original DAMOS or A2L files.

Working from request to measured result

For the separately documented Simos 12 1.8 TSI, SEAT SSP 158 describes charge pressure being regulated to deliver requested torque, with an electric wastegate actuator and position feedback. It does not validate the seller's individual labels, addresses or the illustrated file. A torque request, a permitted limit, the air or pressure target, and the actual pressure or independently measured wheel output are distinct observations.

  1. Record the exact ECU hardware, software and calibration identifiers, engine and gearbox, fuel, modifications, and original-file provenance. Compare the definition with the loaded file rather than selecting solely by car or ECU family.
  2. In a validated definition, examine the axes and operating domains of request, torque limit and load-related groups. The presence of many similarly named tables does not identify which is active or whether each needs changing; check any mode selection and data source where the definition permits.
  3. Establish a repeatable baseline. Where supported, log pedal, requested and permitted torque or load, air or pressure target and actual, throttle, wastegate command and position, lambda target and actual, fuel pressure, ignition corrections and temperatures. Verify channel units, sample rate and whether each is measured or calculated.
  4. When a modified file produces little improvement, first check that the intended file is installed and test conditions are comparable. A reduced request suggests a different investigation from an unchanged request that the hardware cannot achieve. Consider cooling, air leaks, fuel, ignition, sensor and gearbox interventions before attributing a result to a particular map.
  5. Review fuel, ignition and component protections alongside torque and air changes. An “optimal” spark or torque reference label is not automatically a commanded value, and raising a limit alone does not establish that pressure, mixture or output will follow. Validate small changes against comparable logs and suitable independent measurement.

The original and modified file, tool/protocol, change record and tests belong together. A calibration-only or supplied virtual original is not necessarily the ECU's present contents or a complete recovery image. See the Simos 12 overview and wastegate diagnosis for factory-system context and tool limitations.

Comparing a file and a log in an editor

The simos.app Tune Editor advertises editing supported Simos 12.1 and 12.2 definitions, comparing cells with the opened file or a reference BIN, and highlighting map cells or curve positions during CSV-log playback. This is a product-specific example, not proof that it supports the 8V0906264B 0002 file above: identify the loaded software and check its current compatibility list first. The editor also describes an airflow-to-torque helper and virtual-dyno estimates; these are analysis aids whose inputs and assumptions need checking, not direct measurements of engine output.

  1. Keep the unmodified source file and record how it was obtained. Open the intended file with its exact definition, then compare a deliberately matched reference. Check units, scaling, axes and table dimensions before interpreting a difference; a similar label across revisions is not enough to establish that two cells represent the same function.
  2. Review differences in requests, limits and related air, fuel and ignition groups together. Record the cells and the reason for each change. An editor's colour or delta shows a numerical difference, not whether the change is appropriate or active under the test conditions.
  3. For a supported CSV log, compare the logged operating point with the map's axes and units. Align channels and timestamps, and consider sampling, interpolation and mode selection. A highlight can help locate the operating region, but is not independent proof that this specific ECU table was selected, that the highlighted value was applied, or that a particular limiter caused the result.
  4. Compare repeatable before-and-after runs with matched fuel, temperature, gear and conditions. Check actual response and independent output where appropriate, investigate unexpected intervention, and keep the original, modified file and test records together. Editing support does not itself establish read or write support; confirm the chosen flashing tool's operations and recovery route separately.

Sources