Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Simos 8.1 is a Siemens/Continental petrol engine-management variant documented by Audi on certain naturally aspirated 2.8 and 3.2 V6 FSI engines with Audi valvelift. These applications use a different air and load strategy from the supercharged 3.0 TFSI examples discussed on the Simos 8.4 and 8.5 page.

Documented applications and identification

Audi Self-Study Programme 411 identifies Simos 8.1 on its 2.8 FSI BDX and 3.2 FSI CALA V6 examples. Its tables describe both as naturally aspirated, with direct injection and variable valve timing. These are specific factory examples, not an exhaustive fitment list. Identify the actual ECU part and hardware numbers, software, calibration, engine, gearbox and installed equipment before selecting a definition or programming method.

The programme compares its Simos 8.1 engines with an earlier 3.2 FSI described as Simos 6D2. That comparison does not make the software or sensor layout interchangeable. The Simos 6 overview covers the earlier documented system. SSP 411 explicitly notes differences between its 2.8 A6 and 3.2 A5 electrical system overviews; use the exact engine and vehicle documentation when investigating signals.

Valve lift and load control

In the SSP 411 engines, intake cam elements move between profiles for low and high valve lift. Audi describes a part-load range in which the throttle is nearly open and load is controlled using intake-cam timing and valve-lift strategy. After changeover to full lift, load is again controlled using the throttle and manifold pressure. Audi characterises this as a pressure, inlet-cam position and engine-speed based control strategy, not a simple pressure-and-speed model throughout the range.

This matters when interpreting logs. A wide throttle opening at a light or moderate load is not automatically a stuck throttle on this system, and throttle angle alone does not establish cylinder air charge. Compare engine speed and pedal with load, manifold pressure, valve-lift operating state and requested versus actual cam positions where accurately supported. The presence or spelling of a diagnostic channel does not establish its units, update rate or availability on another file. SSP 411, engine management.

Audi also describes coordinated lift changeover: ignition, throttle and camshaft positions are adjusted during the transition to reduce a sudden change in torque. Its illustrated transition is one factory example, not a universal threshold or tuning setting. A brief timing or throttle change during a documented transition is not, by itself, proof of knock or an ECU fault; compare operating state, corrections and any relevant fault information.

Intake and fuel details

SSP 411 says the charge motion from partial lift allowed the earlier intake-port charge-motion flaps to be omitted on its new engines. It also describes a variable intake manifold with a changeover function and position sender. These are different functions: eliminating the earlier charge-motion flaps does not mean that all intake changeover mechanisms or their diagnostics are absent.

The documented engines use direct petrol injection. Audi describes a low-pressure sender G410 and fuel metering valve N290 at the high-pressure pump, with high-pressure sensing in the system overview. It also describes a cold-start catalyst-heating mode with split direct-injection events and retarded ignition, followed by homogeneous operation in the other stated ranges. A split direct-injection event does not itself mean port injectors are installed. Check the actual engine and current workshop procedure rather than generalising the training example.

Calibration and diagnosis

Start with fault codes and the mechanical, electrical, fuel and intake baseline. In addition to ordinary lambda, fuel-pressure, ignition and knock-correction checks, compare the valve-lift or changeover state, intake-manifold changeover and intake/exhaust camshaft request and feedback when those channels are available. Record temperature, operating mode, rpm and load so a transition is not compared with steady-state data. A requested position or ECU-estimated torque is not a direct measurement of achieved cylinder filling or crankshaft torque.

The factory source describes the operating strategy, not performance-map addresses or a validated ignition and fuelling recipe. Verify map axes, units and function for the exact software and assess changes with appropriate logs. Do not assume that a Simos 8.4 or 8.5 boost, bypass or map-switching definition applies to 8.1.

For the factory-described actuator return signal, CALA/CALB implausible-signal codes and a scoped service bulletin, see V6 FSI valve-lift actuator diagnosis.

Programming and recovery scope

A historical CMDFlash release note lists a Simos 8.1 A6 2.8 FSI example and describes a virtual-read and writing workflow for that product. A virtual read is a matching file supplied by a tool or database; it is not necessarily a complete physical read of the actual controller. Confirm the chosen tool's current coverage, file provenance, checksum handling and supported recovery method for the exact ECU before writing.

In its module 57 manual, page 49, PCMflash separately lists reading, writing and checksum functions for its 2.8 V6 Simos 8.1 coverage. This is a different product's claimed operation from CMDFlash's historical virtual read; neither listing proves its output is a complete memory image or guarantees coverage of every 8.1 ECU. Confirm current protocol, file scope and recovery for the exact unit.

Sources