Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 19
Applies to
Simos 19.6
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

On the North American EA888 Evo4 applications Volkswagen documents with Simos 19.6, crankcase ventilation, tank-vapour purge and turbocharger plumbing interact. A leak, disconnected breather or an incompatible modification can complicate diagnosis of idle, fuel-trim or boost complaints. The system below is the example in Volkswagen SSP 822223; confirm engine, market, ECU and installed hardware before applying it to another car.

Ventilation under vacuum and boost

Volkswagen describes a fine oil separator, pressure-regulating and non-return valves, and paths to the intake manifold and turbocharger. It says two additional one-way valves in the separator module separate the tank-breather and crankcase-breather paths. The training diagram still shows both systems connected to the engine air path; separate control paths do not mean the vapours never enter the same intake system.

During turbocharged operation the documented system uses a suction-jet pump, or Venturi nozzle, at the turbocharger. Charge air drives the pump and generates suction for the breather flow, which enters ahead of the compressor. Volkswagen describes the aim as maintaining crankcase vacuum across idle, part load and boost. The training description is not a specified vacuum setpoint, pressure test or guarantee for a modified breather system.

G950 and a pressure log

SSP 822223 lists G950, called tank ventilation pressure sensor 1, on its ULEV70 specification and locates it in the breather line leading to the turbocharger. Verify that the particular vehicle is equipped with this sensor; the Simos 19.6 designation alone does not establish that it is fitted. It says the sensor measures line pressure in turbocharged mode and helps the ECU recognise a leak that results in lost crankcase vacuum. This is a line-pressure signal and its name does not establish a direct measurement inside the crankcase.SSP 822223 locates G950, called tank ventilation pressure sensor 1, in the breather line leading to the turbocharger. It says the sensor measures line pressure in turbocharged mode and helps the ECU recognise a leak that results in lost crankcase vacuum. This is a line-pressure signal and its name does not establish a direct measurement inside the crankcase.

COBB's Mk8 monitor list separately names a “Crankcase Pressure” channel in its fast-monitor section. The monitor name alone does not establish whether it is raw G950 data, a converted value or another calculation. Confirm the diagnostic description, source, units and reference pressure for the specific ECU and logger before comparing it with a workshop measurement. The list does not provide normal limits or a universal pressure threshold.

Practical checks after an intake or breather change

Record the engine and ECU identification, market, full scan and freeze-frame data, recent intake, turbo or breather work, fuel and calibration. Compare the fitted hose routing, sensor connections and non-return valves with the correct service information. Inspect the breather connections, seals, oil-separator module and turbo-inlet plumbing for disconnection, damage or incorrect assembly. A missing vacuum signal can reflect an actual leak, a sensor or wiring issue, or an altered system; use the manufacturer’s guided diagnosis and specified test equipment to distinguish them. Where supported, log the documented pressure channel with engine speed, throttle, manifold pressure, intake temperature and relevant fuel-trim or lambda data. Capture comparable warm idle, part-load and permitted boost conditions, checking sample rate, units and whether the pressure is absolute or relative. Compare repeat tests under similar conditions; pressure and mixture changes alone do not identify a failed separator or valve. After correcting the identified issue, perform applicable guided tests and compare the same operating points. Retain a functioning ventilation and diagnostic system; a warning light or implausible signal is a reason to investigate the installation, not proof that the engine is breathing correctly.

Aftermarket oil-separation example

RacingLine's VWR130010 product page states that its kit is not suitable for US-market vehicles using an additional PCV pressure sensor, and reports a warning when that sensor is removed. This is a manufacturer-specific fitment statement, not evidence that every aftermarket system removes G950 or that every Simos 19 installation has the same sensor. Check the physical car, applicable rules and the supplier's current instructions before selecting hardware.

Sources

Volkswagen Self-Study Program 822223: 2.0L EA888 EVO4 Engine, pp. 1 and 12–18. Simos 19.6 application examples, breather routing, suction-jet pump and G950 description. Training information rather than a current repair procedure. Accessed 17 November 2026. COBB Engine Monitor List MK8 Vehicles. Product-specific fast-monitor label and units; no attribution to a particular sensor is given in the list. Accessed 17 November 2026. RacingLine VWR130010 oil catch can. Manufacturer's product-specific US-market sensor warning. Accessed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Simos 19.6 EA888 Evo4 crankcase ventilation and pressure logging

On the North American EA888 Evo4 applications Volkswagen documents with Simos 19.6, crankcase ventilation, tank-vapour purge and turbocharger plumbing interact. A leak, disconnected breather or an incompatible modification can complicate diagnosis of idle, fuel-trim or boost complaints. The system below is the example in Volkswagen SSP 822223; confirm engine, market, ECU and installed hardware before applying it to another car.

Ventilation under vacuum and boost

Volkswagen describes a fine oil separator, pressure-regulating and non-return valves, and paths to the intake manifold and turbocharger. It says two additional one-way valves in the separator module separate the tank-breather and crankcase-breather paths. The training diagram still shows both systems connected to the engine air path; separate control paths do not mean the vapours never enter the same intake system.

During turbocharged operation the documented system uses a suction-jet pump, or Venturi nozzle, at the turbocharger. Charge air drives the pump and generates suction for the breather flow, which enters ahead of the compressor. Volkswagen describes the aim as maintaining crankcase vacuum across idle, part load and boost. The training description is not a specified vacuum setpoint, pressure test or guarantee for a modified breather system.

G950 and a pressure log

SSP 822223 locates G950, called tank ventilation pressure sensor 1, in the breather line leading to the turbocharger. It says the sensor measures line pressure in turbocharged mode and helps the ECU recognise a leak that results in lost crankcase vacuum. This is a line-pressure signal and its name does not establish a direct measurement inside the crankcase.

COBB's Mk8 monitor list separately names a “Crankcase Pressure” channel in its fast-monitor section. The monitor name alone does not establish whether it is raw G950 data, a converted value or another calculation. Confirm the diagnostic description, source, units and reference pressure for the specific ECU and logger before comparing it with a workshop measurement. The list does not provide normal limits or a universal pressure threshold.

Practical checks after an intake or breather change

  1. Record the engine and ECU identification, market, full scan and freeze-frame data, recent intake, turbo or breather work, fuel and calibration. Compare the fitted hose routing, sensor connections and non-return valves with the correct service information.
  2. Inspect the breather connections, seals, oil-separator module and turbo-inlet plumbing for disconnection, damage or incorrect assembly. A missing vacuum signal can reflect an actual leak, a sensor or wiring issue, or an altered system; use the manufacturer’s guided diagnosis and specified test equipment to distinguish them.
  3. Where supported, log the documented pressure channel with engine speed, throttle, manifold pressure, intake temperature and relevant fuel-trim or lambda data. Capture comparable warm idle, part-load and permitted boost conditions, checking sample rate, units and whether the pressure is absolute or relative. Compare repeat tests under similar conditions; pressure and mixture changes alone do not identify a failed separator or valve.
  4. After correcting the identified issue, perform applicable guided tests and compare the same operating points. Retain a functioning ventilation and diagnostic system; a warning light or implausible signal is a reason to investigate the installation, not proof that the engine is breathing correctly.

Aftermarket oil-separation example

RacingLine's VWR130010 product page states that its kit is not suitable for US-market vehicles using an additional PCV pressure sensor, and reports a warning when that sensor is removed. This is a manufacturer-specific fitment statement, not evidence that every aftermarket system removes G950 or that every Simos 19 installation has the same sensor. Check the physical car, applicable rules and the supplier's current instructions before selecting hardware.

Sources

Revision 2: Simos 19.6 EA888 Evo4 crankcase ventilation and pressure logging

On the North American EA888 Evo4 applications Volkswagen documents with Simos 19.6, crankcase ventilation, tank-vapour purge and turbocharger plumbing interact. A leak, disconnected breather or an incompatible modification can complicate diagnosis of idle, fuel-trim or boost complaints. The system below is the example in Volkswagen SSP 822223; confirm engine, market, ECU and installed hardware before applying it to another car.

Ventilation under vacuum and boost

Volkswagen describes a fine oil separator, pressure-regulating and non-return valves, and paths to the intake manifold and turbocharger. It says two additional one-way valves in the separator module separate the tank-breather and crankcase-breather paths. The training diagram still shows both systems connected to the engine air path; separate control paths do not mean the vapours never enter the same intake system.

During turbocharged operation the documented system uses a suction-jet pump, or Venturi nozzle, at the turbocharger. Charge air drives the pump and generates suction for the breather flow, which enters ahead of the compressor. Volkswagen describes the aim as maintaining crankcase vacuum across idle, part load and boost. The training description is not a specified vacuum setpoint, pressure test or guarantee for a modified breather system.

G950 and a pressure log

SSP 822223 lists G950, called tank ventilation pressure sensor 1, on its ULEV70 specification and locates it in the breather line leading to the turbocharger. Verify that the particular vehicle is equipped with this sensor; the Simos 19.6 designation alone does not establish that it is fitted. It says the sensor measures line pressure in turbocharged mode and helps the ECU recognise a leak that results in lost crankcase vacuum. This is a line-pressure signal and its name does not establish a direct measurement inside the crankcase.

COBB's Mk8 monitor list separately names a “Crankcase Pressure” channel in its fast-monitor section. The monitor name alone does not establish whether it is raw G950 data, a converted value or another calculation. Confirm the diagnostic description, source, units and reference pressure for the specific ECU and logger before comparing it with a workshop measurement. The list does not provide normal limits or a universal pressure threshold.

Practical checks after an intake or breather change

  1. Record the engine and ECU identification, market, full scan and freeze-frame data, recent intake, turbo or breather work, fuel and calibration. Compare the fitted hose routing, sensor connections and non-return valves with the correct service information.
  2. Inspect the breather connections, seals, oil-separator module and turbo-inlet plumbing for disconnection, damage or incorrect assembly. A missing vacuum signal can reflect an actual leak, a sensor or wiring issue, or an altered system; use the manufacturer’s guided diagnosis and specified test equipment to distinguish them.
  3. Where supported, log the documented pressure channel with engine speed, throttle, manifold pressure, intake temperature and relevant fuel-trim or lambda data. Capture comparable warm idle, part-load and permitted boost conditions, checking sample rate, units and whether the pressure is absolute or relative. Compare repeat tests under similar conditions; pressure and mixture changes alone do not identify a failed separator or valve.
  4. After correcting the identified issue, perform applicable guided tests and compare the same operating points. Retain a functioning ventilation and diagnostic system; a warning light or implausible signal is a reason to investigate the installation, not proof that the engine is breathing correctly.

Aftermarket oil-separation example

RacingLine's VWR130010 product page states that its kit is not suitable for US-market vehicles using an additional PCV pressure sensor, and reports a warning when that sensor is removed. This is a manufacturer-specific fitment statement, not evidence that every aftermarket system removes G950 or that every Simos 19 installation has the same sensor. Check the physical car, applicable rules and the supplier's current instructions before selecting hardware.

Sources