Page organisation in this revision
- Page type
- Technical article
- Subject
- Tuning
- Parent
- Simos 6
- Applies to
- Simos 6
- Tool groups
- None
- Manufacturers
- Audi
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Audi's 2005 A6 3.2 FSI technical data identifies Siemens Simos 6, a pressure-based air system, a two-stage intake manifold and charge-motion flaps. On the related 3.2 V6 FSI described in Audi SSP 327, the variable-length manifold and charge-motion flaps are separate systems. This guide uses that training example and an Audi service bulletin to help investigate a power or intake-flap complaint before changing a calibration. Check the actual ECU, engine and vehicle documentation; the bulletin's vehicle list alone does not establish the ECU suffix.
Two sets of flaps
Audi SSP 327, pages 22–23, describes a variable-length 3.2 V6 FSI manifold with two linked manifold flaps. Vacuum moves the linked shafts, a changeover valve controls that vacuum, and a potentiometer reports flap position to the Simos controller. The manifold upper section also contains a vacuum reservoir. These are the training example's components; verify their identification and test procedure on the specific vehicle.
The same programme describes separate charge-motion flaps in the intake passages. They can close the lower part of each passage to increase air velocity and create tumble motion for mixture formation. The ECU controls their vacuum-operated changeover and receives left- and right-side position signals from G512 and G336 respectively in the illustrated engine. A length-change flap position is therefore not, by itself, proof that both banks' charge-motion flaps have moved. Check actual diagnostic channel definitions and bank assignments for the vehicle.
Audi's scoped vacuum-leak example
Audi TSB 01 14 76, 2019485/3, dated 15 April 2014, applies to the listed 2005–2008 A6 and A4 3.2 FSI and 2007–2008 A4 Cabriolet 3.2 FSI. It describes a malfunction indicator and one or more of P2070 (intake-manifold tuning valve stuck open), P2006 (runner control stuck closed, bank 1) or P2007 (runner control stuck closed, bank 2). It notes possible slight power loss at high engine speed and states that the bulletin's condition does not cause stalling. These codes or symptoms alone do not prove that this bulletin's vacuum leak is present.
Audi identifies cracked vacuum lines in the bulletin. Its test isolates the lines to locate a leak and, if vacuum remains stable, checks the appropriate actuator diaphragm: the intake-manifold tuning diaphragm for P2070 or the runner actuator diaphragm for P2006/P2007. Replace only the line found to leak and follow current vehicle-specific diagnostic and repair information. The bulletin does not establish a generic vacuum value or a mandatory part replacement for every code.
Logging and diagnosis
Record the full ECU and software identification, engine code, modifications, fuel, fault scan and freeze-frame conditions. Check the service bulletin's vehicle applicability; the A6 data sheet identifies a Simos 6 example, while the bulletin does not specify a Simos suffix for each car.
Where supported, capture engine speed, throttle, manifold pressure, load, intake temperature and each available manifold or charge-motion flap command and feedback channel during repeatable operation. Check units, signal names and which flap each channel describes. A command is not measured movement and an ECU-estimated load or torque is not an independent output measurement.
For a scoped P2070, P2006 or P2007 complaint, inspect the vacuum supply, hoses, reservoir connections and linkage using the specified service procedure. Audi's bulletin uses a vacuum pump and section isolation, then points to the relevant actuator diaphragm if the lines hold vacuum. A fault can also require electrical, position-sensor or mechanical investigation under the current diagnostic procedure.
After resolving the fault, perform the applicable guided tests and compare logs at similar temperature and load. Check the air path and fuel system before interpreting remaining power differences as map behaviour. Do not disable feedback or diagnostic monitoring to conceal an unresolved mechanical problem.
These sources describe factory hardware and a specific fault investigation; they do not identify software-specific map addresses, flap-switching maps, or a universal changeover speed. Verify any definition against the exact calibration before editing.
Sources
Audi A6 3.2 FSI technical data, August 2005. Simos 6 and documented intake-system configuration. Accessed 17 November 2026.
Audi Self-Study Programme 327, Audi chain-driven engines, French edition, pages 22–23. Variable-length manifold and charge-motion flaps in the described 3.2 V6 FSI. Accessed 17 November 2026.
Audi TSB 01 14 76, 2019485/3, 15 April 2014, NHTSA-hosted copy. Vehicle scope, vacuum leak and diaphragm test. Accessed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Simos 6 3.2 FSI intake flaps and vacuum diagnosis
Audi's 2005 A6 3.2 FSI technical data identifies Siemens Simos 6, a pressure-based air system, a two-stage intake manifold and charge-motion flaps. On the related 3.2 V6 FSI described in Audi SSP 327, the variable-length manifold and charge-motion flaps are separate systems. This guide uses that training example and an Audi service bulletin to help investigate a power or intake-flap complaint before changing a calibration. Check the actual ECU, engine and vehicle documentation; the bulletin's vehicle list alone does not establish the ECU suffix.
Two sets of flaps
Audi SSP 327, pages 22–23, describes a variable-length 3.2 V6 FSI manifold with two linked manifold flaps. Vacuum moves the linked shafts, a changeover valve controls that vacuum, and a potentiometer reports flap position to the Simos controller. The manifold upper section also contains a vacuum reservoir. These are the training example's components; verify their identification and test procedure on the specific vehicle.
The same programme describes separate charge-motion flaps in the intake passages. They can close the lower part of each passage to increase air velocity and create tumble motion for mixture formation. The ECU controls their vacuum-operated changeover and receives left- and right-side position signals from G512 and G336 respectively in the illustrated engine. A length-change flap position is therefore not, by itself, proof that both banks' charge-motion flaps have moved. Check actual diagnostic channel definitions and bank assignments for the vehicle.
Audi's scoped vacuum-leak example
Audi TSB 01 14 76, 2019485/3, dated 15 April 2014, applies to the listed 2005–2008 A6 and A4 3.2 FSI and 2007–2008 A4 Cabriolet 3.2 FSI. It describes a malfunction indicator and one or more of P2070 (intake-manifold tuning valve stuck open), P2006 (runner control stuck closed, bank 1) or P2007 (runner control stuck closed, bank 2). It notes possible slight power loss at high engine speed and states that the bulletin's condition does not cause stalling. These codes or symptoms alone do not prove that this bulletin's vacuum leak is present.
Audi identifies cracked vacuum lines in the bulletin. Its test isolates the lines to locate a leak and, if vacuum remains stable, checks the appropriate actuator diaphragm: the intake-manifold tuning diaphragm for P2070 or the runner actuator diaphragm for P2006/P2007. Replace only the line found to leak and follow current vehicle-specific diagnostic and repair information. The bulletin does not establish a generic vacuum value or a mandatory part replacement for every code.
Logging and diagnosis
- Record the full ECU and software identification, engine code, modifications, fuel, fault scan and freeze-frame conditions. Check the service bulletin's vehicle applicability; the A6 data sheet identifies a Simos 6 example, while the bulletin does not specify a Simos suffix for each car.
- Where supported, capture engine speed, throttle, manifold pressure, load, intake temperature and each available manifold or charge-motion flap command and feedback channel during repeatable operation. Check units, signal names and which flap each channel describes. A command is not measured movement and an ECU-estimated load or torque is not an independent output measurement.
- For a scoped P2070, P2006 or P2007 complaint, inspect the vacuum supply, hoses, reservoir connections and linkage using the specified service procedure. Audi's bulletin uses a vacuum pump and section isolation, then points to the relevant actuator diaphragm if the lines hold vacuum. A fault can also require electrical, position-sensor or mechanical investigation under the current diagnostic procedure.
- After resolving the fault, perform the applicable guided tests and compare logs at similar temperature and load. Check the air path and fuel system before interpreting remaining power differences as map behaviour. Do not disable feedback or diagnostic monitoring to conceal an unresolved mechanical problem.
These sources describe factory hardware and a specific fault investigation; they do not identify software-specific map addresses, flap-switching maps, or a universal changeover speed. Verify any definition against the exact calibration before editing.
Sources
Revision 1: Simos 6 3.2 FSI intake flaps and vacuum diagnosis
Audi's 2005 A6 3.2 FSI technical data identifies Siemens Simos 6, a pressure-based air system, a two-stage intake manifold and charge-motion flaps. On the related 3.2 V6 FSI described in Audi SSP 327, the variable-length manifold and charge-motion flaps are separate systems. This guide uses that training example and an Audi service bulletin to help investigate a power or intake-flap complaint before changing a calibration. Check the actual ECU, engine and vehicle documentation; the bulletin's vehicle list alone does not establish the ECU suffix.
Two sets of flaps
Audi SSP 327, pages 22–23, describes a variable-length 3.2 V6 FSI manifold with two linked manifold flaps. Vacuum moves the linked shafts, a changeover valve controls that vacuum, and a potentiometer reports flap position to the Simos controller. The manifold upper section also contains a vacuum reservoir. These are the training example's components; verify their identification and test procedure on the specific vehicle.
The same programme describes separate charge-motion flaps in the intake passages. They can close the lower part of each passage to increase air velocity and create tumble motion for mixture formation. The ECU controls their vacuum-operated changeover and receives left- and right-side position signals from G512 and G336 respectively in the illustrated engine. A length-change flap position is therefore not, by itself, proof that both banks' charge-motion flaps have moved. Check actual diagnostic channel definitions and bank assignments for the vehicle.
Audi's scoped vacuum-leak example
Audi TSB 01 14 76, 2019485/3, dated 15 April 2014, applies to the listed 2005–2008 A6 and A4 3.2 FSI and 2007–2008 A4 Cabriolet 3.2 FSI. It describes a malfunction indicator and one or more of P2070 (intake-manifold tuning valve stuck open), P2006 (runner control stuck closed, bank 1) or P2007 (runner control stuck closed, bank 2). It notes possible slight power loss at high engine speed and states that the bulletin's condition does not cause stalling. These codes or symptoms alone do not prove that this bulletin's vacuum leak is present.
Audi identifies cracked vacuum lines in the bulletin. Its test isolates the lines to locate a leak and, if vacuum remains stable, checks the appropriate actuator diaphragm: the intake-manifold tuning diaphragm for P2070 or the runner actuator diaphragm for P2006/P2007. Replace only the line found to leak and follow current vehicle-specific diagnostic and repair information. The bulletin does not establish a generic vacuum value or a mandatory part replacement for every code.
Logging and diagnosis
- Record the full ECU and software identification, engine code, modifications, fuel, fault scan and freeze-frame conditions. Check the service bulletin's vehicle applicability; the A6 data sheet identifies a Simos 6 example, while the bulletin does not specify a Simos suffix for each car.
- Where supported, capture engine speed, throttle, manifold pressure, load, intake temperature and each available manifold or charge-motion flap command and feedback channel during repeatable operation. Check units, signal names and which flap each channel describes. A command is not measured movement and an ECU-estimated load or torque is not an independent output measurement.
- For a scoped P2070, P2006 or P2007 complaint, inspect the vacuum supply, hoses, reservoir connections and linkage using the specified service procedure. Audi's bulletin uses a vacuum pump and section isolation, then points to the relevant actuator diaphragm if the lines hold vacuum. A fault can also require electrical, position-sensor or mechanical investigation under the current diagnostic procedure.
- After resolving the fault, perform the applicable guided tests and compare logs at similar temperature and load. Check the air path and fuel system before interpreting remaining power differences as map behaviour. Do not disable feedback or diagnostic monitoring to conceal an unresolved mechanical problem.
These sources describe factory hardware and a specific fault investigation; they do not identify software-specific map addresses, flap-switching maps, or a universal changeover speed. Verify any definition against the exact calibration before editing.
Sources