Page organisation in this revision
- Page type
- Technical article
- Subject
- Tuning
- Parent
- Simos 8.1
- Applies to
- Simos 8.1, Simos 8.2
- Tool groups
- None
- Manufacturers
- Audi
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Audi's naturally aspirated 3.2 FSI CALA and CALB V6 examples use Audi valvelift on the intake camshafts. The Simos 8.1 and Simos 8.2 overview pages identify documented CALA and CALB applications respectively. An apparent loss of torque or a poor transition can be mechanical or electrical, so establish valve-lift operation before revising the calibration.
How the changeover is confirmed
On the BDX and CALA engines described in Audi SSP 411, each cylinder has two electromagnetic valve-lift actuators. One pin engages a groove in the sliding cam element; cam rotation moves the element to the other profile and the groove pushes the pin back. Audi says that the returning magnet induces a voltage pulse in the actuator coil, which the ECU uses as a return signal. The pulse is evidence of the described return event; it is not a continuously measured cam-lift position.
Valve-lift actuators and camshaft timing adjusters perform different functions. A requested cam timing value alone does not verify that each cylinder has changed lift. Record exact DTCs, engine code, ECU identification, operating conditions and available lift state, cam position, load and throttle channels. Confirm what each channel actually reports for that software.
Specific implausible-signal faults
Audi TSB 15 12 25, 2031085/1, dated 10 October 2012, applies to the listed 2009 A4 and A5 CALA, 2010–2012 A6 CALA, and 2009–2012 Q5 CALB vehicles. It describes a MIL and any of the following actuator implausible-signal faults. Check the bulletin and current workshop information against the actual vehicle; these codes alone do not establish that the bulletin's mechanical condition is present.
CylinderActuator AActuator B
1P11A2P11A4
2P11A6P11A8
3P11AAP11AC
4P11AEP11B0
5P11B2P11B4
6P11B6P11B8
Audi explains that the fault can be stored when the return impulse is absent or arrives at the wrong time. Its bulletin specifies a pin-tip-to-camshaft clearance check with the actuator at rest, measuring to the base circle outside the groove, and identifies a condition for a particular revised actuator. Follow the bulletin's figures and current repair and parts information rather than fitting that actuator to every car or treating the fault code as a parts diagnosis.
Test and interpretation
Save a complete fault scan and freeze-frame data before clearing anything. Confirm the affected cylinder and actuator from the full description, rather than assuming that every cam-related fault concerns valve lift. Investigate power, connections and wiring under the appropriate diagnostic procedure.
For the BDX/CALA training example, SSP 411 describes basic setting data block 155 as a changeover check, with the engine warmed and both small- and large-cam result traces. This is a system test that commands a transition, not proof that all actuator output tests or the same data-block numbering exist on every Simos ECU. Use the current guided test and its prerequisites for the actual vehicle.
If the specified test fails or the scoped bulletin applies, inspect the relevant actuator, connector and mechanism under the service procedure. Keep connectors correctly identified; SSP 411 warns against interchanging them. The bulletin's clearance measurement requires its stated geometry and illustrations. Other electrical or mechanical causes remain possible.
After the repair, recheck faults and the specified system test, then compare repeatable logs at similar temperature and load. Keep ECU-estimated torque separate from measured output and distinguish a changeover transient from sustained loss of torque.
SSP 411 describes different fallback responses depending on whether the small or large lift position cannot be reached. Its example limits engine speed and illuminates EPC when the change to large lift fails; a failure to change to small lift has a different response. These are training-example behaviours, not universal symptom rules for every engine and software.
Sources
Audi Self-Study Programme 411: 2.8 and 3.2 FSI engines with Audi valvelift, especially pages 19–22. BDX/CALA actuator mechanics, return signal, basic-setting example and fallback. Accessed 17 November 2026.
Audi TSB 15 12 25, 2031085/1: Cam adjuster, implausible signal – V6 FSI AVS, 10 October 2012, via NHTSA. Vehicle scope, fault codes and clearance check. Accessed 17 November 2026.
Audi of America, 2009 Audi Q5 vehicle introduction, SSP 994803, third-party mirror. CALB and Simos 8.2 identification. Accessed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Simos 8.1 and 8.2 V6 FSI valve-lift actuator diagnosis
Audi's naturally aspirated 3.2 FSI CALA and CALB V6 examples use Audi valvelift on the intake camshafts. The Simos 8.1 and Simos 8.2 overview pages identify documented CALA and CALB applications respectively. An apparent loss of torque or a poor transition can be mechanical or electrical, so establish valve-lift operation before revising the calibration.
How the changeover is confirmed
On the BDX and CALA engines described in Audi SSP 411, each cylinder has two electromagnetic valve-lift actuators. One pin engages a groove in the sliding cam element; cam rotation moves the element to the other profile and the groove pushes the pin back. Audi says that the returning magnet induces a voltage pulse in the actuator coil, which the ECU uses as a return signal. The pulse is evidence of the described return event; it is not a continuously measured cam-lift position.
Valve-lift actuators and camshaft timing adjusters perform different functions. A requested cam timing value alone does not verify that each cylinder has changed lift. Record exact DTCs, engine code, ECU identification, operating conditions and available lift state, cam position, load and throttle channels. Confirm what each channel actually reports for that software.
Specific implausible-signal faults
Audi TSB 15 12 25, 2031085/1, dated 10 October 2012, applies to the listed 2009 A4 and A5 CALA, 2010–2012 A6 CALA, and 2009–2012 Q5 CALB vehicles. It describes a MIL and any of the following actuator implausible-signal faults. Check the bulletin and current workshop information against the actual vehicle; these codes alone do not establish that the bulletin's mechanical condition is present.
| Cylinder | Actuator A | Actuator B |
| 1 | P11A2 | P11A4 |
| 2 | P11A6 | P11A8 |
| 3 | P11AA | P11AC |
| 4 | P11AE | P11B0 |
| 5 | P11B2 | P11B4 |
| 6 | P11B6 | P11B8 |
Audi explains that the fault can be stored when the return impulse is absent or arrives at the wrong time. Its bulletin specifies a pin-tip-to-camshaft clearance check with the actuator at rest, measuring to the base circle outside the groove, and identifies a condition for a particular revised actuator. Follow the bulletin's figures and current repair and parts information rather than fitting that actuator to every car or treating the fault code as a parts diagnosis.
Test and interpretation
- Save a complete fault scan and freeze-frame data before clearing anything. Confirm the affected cylinder and actuator from the full description, rather than assuming that every cam-related fault concerns valve lift. Investigate power, connections and wiring under the appropriate diagnostic procedure.
- For the BDX/CALA training example, SSP 411 describes basic setting data block 155 as a changeover check, with the engine warmed and both small- and large-cam result traces. This is a system test that commands a transition, not proof that all actuator output tests or the same data-block numbering exist on every Simos ECU. Use the current guided test and its prerequisites for the actual vehicle.
- If the specified test fails or the scoped bulletin applies, inspect the relevant actuator, connector and mechanism under the service procedure. Keep connectors correctly identified; SSP 411 warns against interchanging them. The bulletin's clearance measurement requires its stated geometry and illustrations. Other electrical or mechanical causes remain possible.
- After the repair, recheck faults and the specified system test, then compare repeatable logs at similar temperature and load. Keep ECU-estimated torque separate from measured output and distinguish a changeover transient from sustained loss of torque.
SSP 411 describes different fallback responses depending on whether the small or large lift position cannot be reached. Its example limits engine speed and illuminates EPC when the change to large lift fails; a failure to change to small lift has a different response. These are training-example behaviours, not universal symptom rules for every engine and software.
Sources
- Audi Self-Study Programme 411: 2.8 and 3.2 FSI engines with Audi valvelift, especially pages 19–22. BDX/CALA actuator mechanics, return signal, basic-setting example and fallback. Accessed 17 November 2026.
- Audi TSB 15 12 25, 2031085/1: Cam adjuster, implausible signal – V6 FSI AVS, 10 October 2012, via NHTSA. Vehicle scope, fault codes and clearance check. Accessed 17 November 2026.
- Audi of America, 2009 Audi Q5 vehicle introduction, SSP 994803, third-party mirror. CALB and Simos 8.2 identification. Accessed 17 November 2026.
Revision 1: Simos 8.1 and 8.2 V6 FSI valve-lift actuator diagnosis
Audi's naturally aspirated 3.2 FSI CALA and CALB V6 examples use Audi valvelift on the intake camshafts. The Simos 8.1 and Simos 8.2 overview pages identify documented CALA and CALB applications respectively. An apparent loss of torque or a poor transition can be mechanical or electrical, so establish valve-lift operation before revising the calibration.
How the changeover is confirmed
On the BDX and CALA engines described in Audi SSP 411, each cylinder has two electromagnetic valve-lift actuators. One pin engages a groove in the sliding cam element; cam rotation moves the element to the other profile and the groove pushes the pin back. Audi says that the returning magnet induces a voltage pulse in the actuator coil, which the ECU uses as a return signal. The pulse is evidence of the described return event; it is not a continuously measured cam-lift position.
Valve-lift actuators and camshaft timing adjusters perform different functions. A requested cam timing value alone does not verify that each cylinder has changed lift. Record exact DTCs, engine code, ECU identification, operating conditions and available lift state, cam position, load and throttle channels. Confirm what each channel actually reports for that software.
Specific implausible-signal faults
Audi TSB 15 12 25, 2031085/1, dated 10 October 2012, applies to the listed 2009 A4 and A5 CALA, 2010–2012 A6 CALA, and 2009–2012 Q5 CALB vehicles. It describes a MIL and any of the following actuator implausible-signal faults. Check the bulletin and current workshop information against the actual vehicle; these codes alone do not establish that the bulletin's mechanical condition is present.
| Cylinder | Actuator A | Actuator B |
| 1 | P11A2 | P11A4 |
| 2 | P11A6 | P11A8 |
| 3 | P11AA | P11AC |
| 4 | P11AE | P11B0 |
| 5 | P11B2 | P11B4 |
| 6 | P11B6 | P11B8 |
Audi explains that the fault can be stored when the return impulse is absent or arrives at the wrong time. Its bulletin specifies a pin-tip-to-camshaft clearance check with the actuator at rest, measuring to the base circle outside the groove, and identifies a condition for a particular revised actuator. Follow the bulletin's figures and current repair and parts information rather than fitting that actuator to every car or treating the fault code as a parts diagnosis.
Test and interpretation
- Save a complete fault scan and freeze-frame data before clearing anything. Confirm the affected cylinder and actuator from the full description, rather than assuming that every cam-related fault concerns valve lift. Investigate power, connections and wiring under the appropriate diagnostic procedure.
- For the BDX/CALA training example, SSP 411 describes basic setting data block 155 as a changeover check, with the engine warmed and both small- and large-cam result traces. This is a system test that commands a transition, not proof that all actuator output tests or the same data-block numbering exist on every Simos ECU. Use the current guided test and its prerequisites for the actual vehicle.
- If the specified test fails or the scoped bulletin applies, inspect the relevant actuator, connector and mechanism under the service procedure. Keep connectors correctly identified; SSP 411 warns against interchanging them. The bulletin's clearance measurement requires its stated geometry and illustrations. Other electrical or mechanical causes remain possible.
- After the repair, recheck faults and the specified system test, then compare repeatable logs at similar temperature and load. Keep ECU-estimated torque separate from measured output and distinguish a changeover transient from sustained loss of torque.
SSP 411 describes different fallback responses depending on whether the small or large lift position cannot be reached. Its example limits engine speed and illuminates EPC when the change to large lift fails; a failure to change to small lift has a different response. These are training-example behaviours, not universal symptom rules for every engine and software.
Sources
- Audi Self-Study Programme 411: 2.8 and 3.2 FSI engines with Audi valvelift, especially pages 19–22. BDX/CALA actuator mechanics, return signal, basic-setting example and fallback. Accessed 17 November 2026.
- Audi TSB 15 12 25, 2031085/1: Cam adjuster, implausible signal – V6 FSI AVS, 10 October 2012, via NHTSA. Vehicle scope, fault codes and clearance check. Accessed 17 November 2026.
- Audi of America, 2009 Audi Q5 vehicle introduction, SSP 994803, third-party mirror. CALB and Simos 8.2 identification. Accessed 17 November 2026.