Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Simos 11 is a Volkswagen Group petrol engine-management family. Škoda workshop documentation identifies it on selected naturally aspirated 1.2 MPI three-cylinder engines. Identify the controller and its exact software before selecting a definition or flashing procedure.

Applications and identification

The Škoda Fabia II, Roomster and Rapid 1.2 MPI workshop manual (August 2012, technical data pages 1–4) lists Simos 11 on CGPA, CHFA and CJLA examples from the May 2011 changeover, and on CGPB examples. The same table lists Simos 9 on earlier CGPA, CHFA and CJLA examples. It does not give a Simos 11 suffix, and the changeover month alone is not proof of the controller fitted to an individual car. Record the label, hardware, software and calibration identifiers as well as the vehicle and engine code.

In that manual, CGPA is a 1,198 cm³ three-cylinder, 12-valve, 51 kW MPI example; the listed engine has two lambda probes and no turbocharger or camshaft adjustment. The CGPB and CHFA configurations differ. These are engine- and market-specific details, not common features of every Simos 11 application. An Engineering Mechanics 2016 paper describes a Simos 11-controlled 1,198 cm³ Škoda laboratory engine with the same 51 kW and 12-valve characteristics. Its liquid-LPG injector experiment is a research setup, not proof of a factory LPG application or of a particular ECU suffix.

Some tool catalogues associate 11.1 with 1.2 TSI badges: Microtronik's SEAT list includes both an Ibiza 1.2 12v and several 1.2 TSI entries. Conversely, SEAT SSP 136 describes its 1.2 TSI with Simos 10. Treat these as differently scoped records, not proof of ECU interchangeability or of the fitted ECU in an unspecified TSI. Simos 10 has its own overview.

MPI baseline and fuel-system checks

Before calibration changes, investigate stored faults, ignition and misfires, intake leaks, lambda behaviour and fuel delivery. Where available, log engine speed and load, throttle position, lambda target and actual, fuel trims, ignition timing, knock correction and temperatures. Verify the logger's units, sample rate and whether each value is measured or calculated; availability varies with software and tool. A repeatable baseline helps separate a pre-existing fault from a calibration effect.

For the engines covered by the August 2012 Škoda MPI manual, its operating-pressure procedure measures at the fuel feed line with the engine running and specifies 3.92–4.20 bar using its stated gauge and procedure (pages 119–120). This is a workshop test specification for that documented fuel system, not a universal Simos 11 target or a tuning recommendation. Follow the applicable current service instructions for the individual vehicle and gauge connection. The manual also describes checking injector leakage, spray pattern and delivered quantity under controlled test conditions (pages 153–155), which can help explain mixture problems before altering fuel maps.

Calibration and reading

Map definitions and their axes, units and scaling must match the exact software. The sources here do not establish a universal Simos 11 torque or fuel map layout, safe numerical increases, or transferable addresses. Avoid assuming a pressure control strategy from a different engine or copying definitions merely because the ECU family name is similar.

Microtronik's Simos 11.1 product page lists OBD read, virtual read and write for its tool. That is a product-specific coverage statement; check current support, preparation and recovery for the actual ECU and software. A virtual original need not contain the vehicle's current calibration, and a calibration read is not necessarily a complete memory image. Confirm the original file scope, checksum handling, stable power and recovery method before writing.

Sources